Putra, Wahyuaji Narottama
Departemen Teknik Metalurgi Dan Material, Fakultas Teknik, Universitas Indonesia, Depok

Published : 10 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 10 Documents
Search

Effect of Sodium Dodecyl Benzene Sulfonate Addition as Surfactant in Carbon Nanofluid for Quench Medium Application Maulana Naufalino; Mohammad Ilham Daradjat; Ravanya Nabilla Ramadhani Parawansa; Benediktus Ma'dika; Ghiska Ramahdita; Sri Harjanto; Wahyuaji Narottama Putra
Jurnal Metalurgi dan Material Indonesia Vol. 1 No. 2 (2018): Desember
Publisher : Badan Kerja Sama Pendidikan Metalurgi dan Material (BKPMM)

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Nanofluids, which are fluids containing suspensions of nanoparticles, have been reported to have higher thermal conductivity than conventional fluid, e.g. water, oil, etc. Because of this characteristic, nanofluids are very attractive in heat transfer applications, such as quenching medium for heat treatment process. This unique characteristic is caused by the nanoparticles inside the fluid that have higher thermal conductivity, thus perform better on heat absorption and heat transfer. By varying the nanoparticles content in the fluid base, the cooling rate can be controlled in accordance with the desired characteristics of the material. Carbon is used as a nanoparticle because of the low cost and environmental friendly characteristics, but still have relatively high thermal conductivity. Unfortunately, carbon nanoparticle is highly hydrophobic. Therefore, surface modification is needed by using surfactant in the nanofluids. In this paper, Sodium Dodecyl Benzene Sulfonate (SDBS) was used as surfactant from 1, 3, and 5% in 100 ml water-based nanofluid with 0.5% volume carbon. The carbon powder used in this research was commercial grade, and ball-milled for 10 hours at 500 rpm to reduce the particle size. Commercially available household bodycare product which contain SDBS was used for surfactant source. Scanning Electron Microscope (SEM) showed that the particle size after milling were roughly 10 µm. Medium carbon steel, S45C, was heated at 1000°C for 1 hour, and then quenched using this nanofluid. Microstructure observation showed martensite phase formation after quenching. Hardness test confirmed this phase, showing hardness up to 949 HV after quenching using surfactant added nanofluid.
Observasi Nanofluid dengan TiO2 sebagai Partikel Nano dan Sodium Dodecyl Benzene Sulfonate sebagai Surfaktan untuk Aplikasi Media Quench Andreas Sugiarto; Aldi Alfarizi; Luthfi Dali Ahmad; Setyoaji Fajar Negara; Ghiska Ramahdita; Sri Harjanto; Wahyuaji Narottama putra
Jurnal Metalurgi dan Material Indonesia Vol. 2 No. 2 (2019): Agustus
Publisher : Badan Kerja Sama Pendidikan Metalurgi dan Material (BKPMM)

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Heating and cooling process in heat treatment is a common process to increase the mechanical properties of steel component. Rapid cooling, or quenching, is needed to change the microstructure to obtain the desire hardness. Recently, nanofluid is widely used as a medium for quenching because of their advantage in heat thermal conductivity compared with conventional medium such as water or oil. Nanofluid is a liquid with high thermal conductivity nanoparticle suspended in the fluid base. The variation of nanoparticles content in nanofluids could control the cooling rate to optimize the desired characteristics of a material. TiO2 is widely used as nanoparticle because of its high thermal conductiviy, relatively cheap and environmental friendly. To improve the suspension of TiO2 nanoparticle in nanofluid, surfactant is added. In this research, Commercial grade TiO2 powder was used as nanoparticle, and common household bodycare which contain Sodium Dodecyl Benzene Sulfonate (SDBS) was used as the source of surfactant. The nanofluid was produced by mixing 100 ml water with 0.1% volume TiO2, and additional 1%, 3%, and 5% SDBS surfactant as variation. Before mixing, the TiO2 powder were milled at 500 rpm for 10 hours. This nanofluid was then used as quenching medium. The steel used as sample in this experiment was S45C medium carbon steel, heated at 1000°C for 1 hour. Scanning Electron Microscope (SEM) was used to determine the TiO2 particle size after milling, and showed roughly less than 100 nm. Microstructure observation showed martensite phase formation after quenching. Hardness test confirmed this phase, showing hardness up to 954 HV after quenching using surfactant added nanofluid.
EFFECT OF H2O2 AND MnO2 AS OXIDATORS OF GOLD AND COPPER LEACH PROCESSES FROM PRINTED CIRCUIT BOARDS Yudha Pratesa; Aji Wibisono; Wahyuaji Narottama Putra; Yunita Sadeli; A. Zakiyuddin; Sri Harjanto
Jurnal Sains Materi Indonesia Vol 20, No 3: APRIL 2019
Publisher : Center for Science & Technology of Advanced Materials - National Nuclear Energy Agency

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (794.453 KB) | DOI: 10.17146/jsmi.2019.20.3.4710

Abstract

In general, electronic waste management in the form 2 of printed circuit boards (printed circuit boards/PCBs) is carried out by the process of removing components and taking precious metals that are easily recycled. However, in Indonesia, the recycling process for extracting precious metals has not been much processed, even though they contain precious metals such as copper and gold. This research was conducted to find a more economical and environmentally friendly treatment process by using an oxidizer of Hydrogen Peroxide (H2O2) and Manganese Oxide (MnO2) and reducing the level of HCl used. Observation of metal leaching results using Atomic Adsroption Spectroscopy (AAS) showed the value of recovery (recovery) of gold and copper reached 59.1% and 59.8% for 0.5M HCl + 2.5% H2O2. However, the recovery value of copper has reached its optimum point at the addition of 1.5% H2O2. The use of 3% & 5% MnO2 results in recovery values of 12% and 24% for gold and copper. Observation of the cross section shows the dissolution of the copper metal from the PCB and accompanied by a change in the color of the solution from clear to green, the more concentrated the more the amount of dissolved copper metal shows the characteristic of CuCl solution. The results of the comparison of the two types of oxidizers show that H2O2 is better than MnO2 in producing higher Cu and Au metals more than 3 times.
The Comparison of Pipe Thickness Selection Method Using Full Flange Rating and non-Full Flange Rating of Cryogenic Services in an LNG Plant Construction Agustar, Ari; Iskandar, Isdaryanto; Putra, Wahyuaji Narottama
Journal of Materials Exploration and Findings Vol. 1, No. 2
Publisher : UI Scholars Hub

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Significant growth of gas demand as a source of power generation for domestic use and industries, mainly in the developed countries, has forced the effort to secure the gas supplies located thousands of miles away across the sea as an economical way of gas transportation instead of transporting by pipeline. LNG technology was created as the solution. Natural gas is refrigerated below its boiling point (-160oC to -162oC), known as cryogenic temperature or cryogenic service. Material of Construction (MOC) selection report showed that 304/304L and 316/316L Stainless Steel pipe could withstand and be suitable for this type of service. However, the SS pipe price could be much more costly than the CS pipe. An alternative philosophy to the full-flange rating is introduced in this paper to reduce SS pipe thickness without sacrificing safety issues and proper engineering practice. The philosophy of the pipe wall-thickness calculation method utilized in this paper showed no impact on the class 150 rating due to the selected thicknesses being equal or higher. However, the class 300 rating successfully reduced pipe selected thickness for pipe sizes larger than 24 inches ranging from 20,15% to 31,1%, and for class 600 rating successfully reduced the thickness ranging from 6,28% to 16,55% for pipe sizes 10 inches and larger. The overall pipe thickness reduction reduced pipe weight for cryogenic services by approximately 91,84 tons. The philosophy of the pipe wall-thickness calculation method for cryogenic services can be extended to all other services in the entire LNG production train to gain maximum cost savings for the pipe purchasing cost.
The Effect of Graphite and Activated Carbon as Dispersed Particle in Base Fluid as Quench Medium on the Hardness of S45C Carbon Steel Putra, Wahyuaji Narottama; Somadinata, Danika Aprilia; Ramahdita, Ghiska
Journal of Materials Exploration and Findings Vol. 1, No. 3
Publisher : UI Scholars Hub

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Adding a solid particle dispersion into a base fluid could increase its thermal conductivity, hence increasing the heat transfer characteristics. One example of this thermally enhanced fluid is in heat treatment industry as quench medium. By controlling the amount of the dispersed particle, the cooling rate of the quench medium can be altered, and could affect steel hardness after heat treatment. In this research, the dispersed particle used was commercially available graphite and activated carbon particle. As for the base fluid, distilled water and common engine oil were compared. The concentration of the dispersed particle was 0.1, 0.3, 0.5 weight percent. The highest hardness was achieved at 728 HV on the 0.1% activated carbon particle in water base fluid. Meanwhile, by using graphite, the highest hardness achieved was at 639 HV on the 0.1% particle in water base fluid. The result may suggest that activated carbon could improve the cooling rate better due to its impurities. As expected, quenching by dispersed graphite particle in oil based resulted in lower hardness on all variables.
THE EFFECT OF PYROLYSIS DURATION ON THERMAL CONDUCTIVITY, STABILITY, AND VISCOSITY OF DISPERSED PCB-BASED PARTICLES IN THERMAL FLUID Putra, Wahyuaji Narottama; Ariati, Myrna; Suharno, Bambang; Ferdian, Deni; Ulum, Reza Miftahul
Jurnal Rekayasa Mesin Vol. 14 No. 3 (2023)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v14i3.1655

Abstract

Solid particles have a higher thermal conductivity compared to a fluid. Therefore, it is a common practice to disperse solid particles inside a base fluid to increase its thermal conductivity. The particle-dispersed fluid is called a thermal fluid. Thermal fluid, such as a coolant, is widely used as a heat transfer fluid. Several types of particles can be used to increase the thermal conductivity of the fluid, i.e., metallic particles, metal-oxide particles, or even carbon-based particles. In this research, a carbon-based particle was used as the dispersed particle. The particle was obtained by processing electronic waste, specifically Printed Circuit Board (PCB). The PCB was pyrolyzed for variable duration at 15, 30, and 45 minutes to increase the carbon content. After pyrolyzing, the particle was milled to reduce its size. Subsequently, the PCB particle was added to distilled water. Sodium Dodecylbenzene Sulfonate (SDBS) was added as a surfactant to increase fluid stability and prevent particle agglomeration. Thermal conductivity was improved by up to a 13% increase at the 15-minute pyrolysis. Adding SDBS surfactant also improves the thermal fluid's stability to -29,1 mV. The fluid's viscosity was slightly increased up to a maximum of 0.984 mPa.S.
THE EFFECT OF PYROLYSIS DURATION ON THERMAL CONDUCTIVITY, STABILITY, AND VISCOSITY OF DISPERSED PCB-BASED PARTICLES IN THERMAL FLUID Putra, Wahyuaji Narottama; Ariati, Myrna; Suharno, Bambang; Ferdian, Deni; Ulum, Reza Miftahul
Jurnal Rekayasa Mesin Vol. 14 No. 3 (2023)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v14i3.1655

Abstract

Solid particles have a higher thermal conductivity compared to a fluid. Therefore, it is a common practice to disperse solid particles inside a base fluid to increase its thermal conductivity. The particle-dispersed fluid is called a thermal fluid. Thermal fluid, such as a coolant, is widely used as a heat transfer fluid. Several types of particles can be used to increase the thermal conductivity of the fluid, i.e., metallic particles, metal-oxide particles, or even carbon-based particles. In this research, a carbon-based particle was used as the dispersed particle. The particle was obtained by processing electronic waste, specifically Printed Circuit Board (PCB). The PCB was pyrolyzed for variable duration at 15, 30, and 45 minutes to increase the carbon content. After pyrolyzing, the particle was milled to reduce its size. Subsequently, the PCB particle was added to distilled water. Sodium Dodecylbenzene Sulfonate (SDBS) was added as a surfactant to increase fluid stability and prevent particle agglomeration. Thermal conductivity was improved by up to a 13% increase at the 15-minute pyrolysis. Adding SDBS surfactant also improves the thermal fluid's stability to -29,1 mV. The fluid's viscosity was slightly increased up to a maximum of 0.984 mPa.S.
Remaining Life Assessment and Fitness for Service Evaluation of Aging Chemical Reactors in Polyethylene Terephthalate Resin Industry Munthe, Aditya Pahlawan; Dhaneswara, Donanta; Putra, Wahyuaji Narottama; Widyaputra, Gama
Journal of Materials Exploration and Findings Vol. 4, No. 2
Publisher : UI Scholars Hub

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 meets all safety requirements. The head and shell thicknesses exceed the minimum allowable values; calculated MAWPr values are above the design MAWP; and thicknesses adjusted for FCA remain above 50% of the minimum required. These results indicate that R-120 remains fit for continued service. This study underscores the critical role of standardized assessment and routine inspection in extending the safe operating life of aging process equipment
Feasibility Analysis of Thermal Oxidizer to Determine Remaining Life Using Fitness- for-Service Level 3 Method Yudistirawan, Yudhi; Dhaneswara, Donanta; Putra, Wahyuaji Narottama; Widyaputra, Gama; Suci, Dewi Kurnia; Mahardhika, Agung Putra
Journal of Materials Exploration and Findings Vol. 5, No. 1
Publisher : UI Scholars Hub

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, an FFS evaluation was conducted based on two criteria: stress and temperature, to ascertain whether the TOX remains safe and operational until the end of its service life. Based on the FFS assessment, the TOX structure has been deemed fit to operate and acceptable for use throughout its remaining service life. Subsequently, a remaining life assessment performed on these components indicated an estimated service life of 20 years. According to the analyses carried out, the maximum stress observed is 160 MPa in the radiant section, while the highest temperature, recorded at 392 °C, occurs in the convection and transition sections. These results indicate that the radiant area particularly the upper radiant component, poses the highest risk due to the stress concentrations at its peak levels. In conclusion, although the TOX system is currently operating safely, periodic inspections are essential to ensure its continued secure operation until the end of its remaining service life.
EFFECT OF H2O2 AND MnO2 AS OXIDATORS OF GOLD AND COPPER LEACH PROCESSES FROM PRINTED CIRCUIT BOARDS Yudha Pratesa; Aji Wibisono; Wahyuaji Narottama Putra; Yunita Sadeli; A. Zakiyuddin; Sri Harjanto
Jurnal Sains Materi Indonesia Vol. 20 No. 3 (2019): Jurnal Sains dan Materi Indonesia
Publisher : BRIN Publishing (Penerbit BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/jsmi.2019.20.3.4710

Abstract

In general, electronic waste management in the form 2 of printed circuit boards (printed circuit boards/PCBs) is carried out by the process of removing components and taking precious metals that are easily recycled. However, in Indonesia, the recycling process for extracting precious metals has not been much processed, even though they contain precious metals such as copper and gold. This research was conducted to find a more economical and environmentally friendly treatment process by using an oxidizer of Hydrogen Peroxide (H2O2) and Manganese Oxide (MnO2) and reducing the level of HCl used. Observation of metal leaching results using Atomic Adsroption Spectroscopy (AAS) showed the value of recovery (recovery) of gold and copper reached 59.1% and 59.8% for 0.5M HCl + 2.5% H2O2. However, the recovery value of copper has reached its optimum point at the addition of 1.5% H2O2. The use of 3% & 5% MnO2 results in recovery values of 12% and 24% for gold and copper. Observation of the cross section shows the dissolution of the copper metal from the PCB and accompanied by a change in the color of the solution from clear to green, the more concentrated the more the amount of dissolved copper metal shows the characteristic of CuCl solution. The results of the comparison of the two types of oxidizers show that H2O2 is better than MnO2 in producing higher Cu and Au metals more than 3 times.