Claim Missing Document
Check
Articles

Found 3 Documents
Search
Journal : J-Innovation

RANCANG BANGUN KONVEYOR PEMISAH BARANG BERDASARKAN WARNA MENGGUKAN SMART RELAY ZELIO effendi effendi; Wahyu Priyanto; Akhmad Faruqi
J-Innovation Vol. 10 No. 1 (2021): Jurnal J-Innovation
Publisher : Politeknik Aceh

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (867.038 KB) | DOI: 10.55600/jipa.v10i1.58

Abstract

The design of this goods separator conveyor aims to replace human labor in separating goods based on color, where the goods separation system is designed using the zelio smart relay (SR3B261BD) as the main controller, the conveyor belts in this system are driven by motor power wondows and are using a color sensor module. (TCS3200) as a color detection sensor which is then separated by a separation arm designed using a DC motor to separate each item according to the predetermined color, namely red, green and blue. The limit switch is used to limit the separation arm. When the goods have been separated, the separating arm will return to the starting position, this process will continue until the next cycle.
DISAIN DAN APLIKASI PENGATUR TEGANGAN AC SATU FASA Effendi
J-Innovation Vol. 8 No. 2 (2019): Jurnal J-Innovation
Publisher : Politeknik Aceh

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (638.207 KB) | DOI: 10.55600/jipa.v8i2.72

Abstract

This single phase AC Voltage controller is arranged using such SCR TIC126, diodes, IC Regulators, Op-Amp LM324N, and several other electronic components.This module can produce AC voltages that vary according to the trigering of the SCR angle that is used, while the frequency of the output voltage waveform is fixed, the analysis of the output voltage waveform in this research is carried out in a simulation form by using the PSIM program, mathematically, and then comparing with the measurement results,as for the parameters measured is the Vrms output voltage. The voltage difference between simulated, mathematical and measurement is not too large,As for the triggering angle that used at of 45˚, 60˚, 90˚, 135˚, where the load used is resistive at 5 W 100 Ω, and the source that used is low AC voltage of 12.8 volts with a frequency of 50 Hz.
SISTEM PENGONTROLAN DAN MONITORING LEVEL TEGANGAN PLC SECARA WIRELESS BERBASIS EMBEDDED LINUX. Muhammad Agil Haikal; Rouhillah; Effendi
J-Innovation Vol. 4 No. 1 (2015): J-Innovation
Publisher : Politeknik Aceh

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (206.353 KB) | DOI: 10.55600/jipa.v4i1.18

Abstract

Programmable Logic Controller (PLC) is not only serves as a smart relay or just on and off the system but also provided an analog input so that the PLC can changes in input voltage levels. PLC also has a serial communication between PLC coupling with other devices. Level analog voltage input has a voltage rating of 0-10 Volt will be converted by the ADC (analog digital converter) to the PLC, and the subsequent response of the ADC program created in the PLC will affect the results output. This reseach was made for monitoring levels of 0-10 Volt input voltage that come from the PLC. ADC control is made will be downloaded to the PLC. PLC will be communicated with the Raspberry Pi which is installed embedded linux-based operating system via Modbus communications, thus controlling which previously via PLC can be taken over by the Raspberry Pi. This research also made for monitoring the working of the system, because the Raspberry Pi was be equipped by wireless that will be used for communication to a PC (personal computer) without using cables. the results of this research is a wireless PC can monitor changes 0-10 Volt analog voltage, the output response on the PLC and PLC output can be controlled in accordance with the desired system