ASLINA BR. GINTING
Unknown Affiliation

Published : 28 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 28 Documents
Search

PENGARUH PELARUT ORGANIK PADA PROSES PERTUKARAN ANION DALAM PEMISAHAN URANIUM DARI LARUTAN PEB U3Si2/Al PASCA IRADIASI Dian Anggraini; Boybul Boybul; Yanlinastuti Yanlinastuti; Arif Nugroho; Rosika Kriswarini; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 2 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.2.3576

Abstract

Separation method of uranium from nuclear fuel solutions was developed to improve the quality of uranium-based analysis of post-irradiation nuclear fuel. The aim of this study was to determine the effect of organic solvent on the anion exchange process on the recovery of U from U3Si2/Al fuel solution post-irradiated. The organic solvent, in this case methanol, contained in solvent medium in the anion exchange column may be possible to increase the resin sorption of the uranium. The materials used are standard solution of uranil nitrat and supernatant solution of Cs separation process from the fuel solution. The uranium separation method from U3Si2/Al post irradiated fuel solution uses two columns of anion exchanger with two stages. The first column uses Dowex 1x8-Cl Dowex resin. Parameters varied in the first column are HNO3 concentrations ranging from 1M; 2M; 3M and 4M. The parameters variation in the second column is the ratio of HCl/methanol volume of 30:70 %; 20:80 % and 10:90 %. The result obtained a maximum U recovery of 90,68 % with feed solution composition in the first column containing 3 % HNO3 and methanol by 50 %volume, while in the second column with 6M HCl composition with methanol in 10 %:90 % ratio. In these conditions obtained uranium content in a solution of the middle PEB U3Si2/Al TMU 2.96 g/cm3 piece of 0.4725 μg.
ANALISIS KANDUNGAN CESIUM DAN URANIUM DALAM BAHAN BAKAR U3Si2/Al PASCA IRADIASI Boybul Boybul; Yanlinastuti Yanlinastuti; Arif Nugroho; Dian Anggraini; Rosika Kriswarini; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 2 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.2.3568

Abstract

Separation of fission product isotopes of 137Cs and 235U has been done to determine content of 137Cs and 235U in irradiated U3Si2/Al fuel plate of 2.96 gU/cm3 density. The initial step in the determination of 137Cs and 235U content is sample cutting process. The cutting position was determined at the top middle and bottom part of the plate by an amount of 0.095 g; 0.1103 g and 0.1441g for each respective position. Each sample was dissolved in 25 mL of HNO3 6N dan HCl 6N to obtain irradiated U3Si2/Al solution. Separation was carried out by cation exchange and precipitation methods. The separation of 137Cs was done by pipetting 150 µL of the irradiated U3Si2/Al sample solution and adding it to 1000 mg of Lampung zeolite, while the separation by precipitation method was done by adding 700 mg of CsNO3 powder as carrier and HClO4 to the U3Si2/Al sample solution. In the cation exchange method, 137Cs would be bound by zeolite in the solid phase in the form of 137Cs-zeolite and uranium would stay in the liquid phase or supernatant. The precipitation was done in an ice bath at -4 oC to obtain 137CsClO4 precipitate. The effluent leaving the column was subjected to electrodeposition process for 235U content measurement with α-spectrometer. The 137Cs content obtained by cation exchange was 401.0335 µg/g FP (FP = irradiated fuel plate); 451.1094 µg/g FP and 343.9651 µg/g FP for each respective sample position by 99 % recovery, while the 137Cs content obtained by precipitation method was 393.4581 µg/g FP; 452.0525 µg/g FP and 330.7839 µg/g FP for each respective sample position by 98 % recovery. The 235U content was found to be 45208 µg/g FP; 50896 µg/g FP and 44336 µg/g FP for each respective sample position by 68 % recovery.
KARAKTERISASI TERMAL PEB U-7Mo/Al SEBAGAI BAHAN BAKAR REAKTOR RISET Sayyidatun Nisa; Ariyanti Saputri; Sutri Indaryati; Noviarty Noviarty; Supardjo; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 2 (2021): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.2.6420

Abstract

UMo/Al-based fuel is a candidate for research reactor fuel and as an alternative to U3Si2/Al fuel. This is because the UMo/Al alloy has a higher uranium density of 16.4 g/cm3 compared to U3Si2/Al of 12.2 g/cm3. In addition, the UMo alloy has a low neutron absorption cross section and its reprocessing process is relatively easy. The U-7Mo/Al alloy is able to maintain the γ-U phase during irradiation process so that the stability of the fuel in the reactor is maintained. The U-7Mo alloy has been fabricated into a U-7Mo/Al mini fuel element plate. The purpose of this study was to determine the thermal characteristics of U-7Mo/Al as inputs to the research reactor fuel fabricator in the manufacture of UMo/Al-based fuel. Thermal characterization was carried out for uranium, molybdenum, UMo and the fuel element plate of U-7Mo/Al using Differential Scanning Calorimetry (DSC). The thermal characterization results show that the U-7Mo/Al fuel element plate is thermally stable up to 600 °C because it undergoes an endothermic thermochemical reaction at a temperature of 632.962 °C with DH = 144.318 J/g. At 656.186 °C, the Al matrix and AlMg2 cladding are fused in the U-7Mo/Al with DH = 144.318 J/g. At temperatures of 952.810 °C to 1106.050 °C, the molten Al matrix diffuses with UMo to form a metastable U(Mo,Al)X compound and heating to a temperature of 1211.760 °C forms a UAlX layer (UAl2, UAl3 and UAl4) with DH = –22,721 J/g.
PEMISAHAN DAN ANALISIS 137Cs DARI LARUTAN PELAT ELEMEN BAKAR U-7%Mo/Al Dian Anggraini; Noviarty Noviarty; Yanlinastuti Yanlinastuti; Aslina Br. Ginting; Rosika Kriswarini; Arif Nugroho; Boybul Boybul
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 3 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.3.3183

Abstract

The aim of this research is to get a valid method of separating cesium from U-7Mo/Al fuel plate solution through determination of parameter of method (accuracy, precision, and recovery). Precipitation method and cation exchange method that are used refer to standard ASTM 690-000 and research result of U3Si2/Al. Parameter method determination has been done by using 150 μL sample (U-7%Mo/Al fuel plate solution, 50 μL of standard solution in 2 mL of HCl 0,1 N. The sample solution was undergone precipitation process by using HClO4 concentrated and 225 mg of CsNO3 as carrier in temperature 0oC for an hour, while exchange cation process was done by using 400 mg of resin zeolite Lampung. The analysis of 137Cs in CsClO4 and 137Cs - zeolite was done by gamma spectrometer. Determination of recovery method was done by comparing count value of 137Cs before and after separation process. Recovery of precipitation method was obtained 95.56 % with accuracy and precision measurement of 0.375 % and 1.875 % respectively, while recovery of cation exchange method obtained 26.73 %. To sum up, the results show that precipitation method better than exchange cation method for separation 137Cs from U-7Mo/Al fuel plate solution.
METODE PENGENDAPAN DAN PENUKAR KATION UNTUK PEMISAHAN CESIUM DALAM BAHAN BAKAR U3Si2-Al Aslina Br. Ginting; Dian Anggraini
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 2 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.2.3092

Abstract

137Cs isotope was one of the fission products which could be used as a burn up monitor to study the performance of the fuel during irradiation in a reactor. For analyzed 137Cs isotope in post-irradiation U3Si2-Al fuel element plate (PEB), it was needed a valid method to obtain accurate data. Several methods could be used for 137Cs separation from U3Si2-Al PEB solution were precipitation method in CsClO4 salt form according to ASTM E 320-79 and cation exchange method using Lampung zeolite. The precipitation process was done using CsNO3 powder as a carrier substance and HClO4 reagent, while the cation exchange process was done by the addition of Lampung zeolite. The objective research was getting a valid method for 137Cs separation in post-irradiation U3Si2-Al PEB, especially for the aspects of CsNO3 powder weight influence and weight of zeolite Lampung was added. 137Cs isotope precipitation process was done by pipetting 150 mL U3Si2-Al PEB solution which was added to the 500; 625; 700; and 1000 mg weight variation CsNO3 powder and 4 mL HClO4 in ice media for 1 hour. The precipitation process results were obtained CsClO4 precipitate separated from the supernatant as a liquid phase. Meanwhile, the cation exchange process was done by adding 700; 900; 1000 and 1200 mg weight variation Lampung zeolite by shaking for 1 hour. The cation exchange process results was obtained 137Cs-zeolite in the solid phase and the other isotopes in the liquid phase. The137Cs content in 137CsClO4 precipitate,137Cs-zeolite solid phase and supernatant was measured using spectrometer-g. The analysis showed that the optimum weight of CsNO3 addition when most binding of 137Cs occurred was 700 mg equal to 0.0472 g 137Cs isotope, while the optimum weight addition of Lampung zeolite was 1000 mg until 1200 mg equal to 137Cs isotope content in137Cs-zeolite obtained was 0.0557 g. The 137Cs isotope separation process using both methods could be concluded that the cation exchange method using zeolite by the addition of 1000 mg Lampung zeolite until 1200 mg had better result than the precipitation method. The other advantages of this method were easier and safer than precipitation methods that the process should be in ice batch (-4oC), using chemicals HClO4, acetone and ethanol which had volatile and exothermic character.
PENGARUH PARAMETER PROSES ELEKTRODEPOSISI TERHADAP PENENTUAN BERAT ISOTOP 235U DALAM PEB U3Si2/Al PASCA IRADIASI Yanlinastuti Yanlinastuti; Boybul Boybul; Aslina Br. Ginting; Dian Anggraini
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 2 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.2.3093

Abstract

Electrodeposition process for determination of 235U isotope is affected by current, contact time, feed volume and type of buffer solution. The aim of this research is to obtain optimum parameter of electrodeposition process for 235U determination in U3Si2/Al irradiated fuel plate. Electrodeposition process is done by some variation of parameters, that are the current 1; 1.2; and 1.4 ampere with variation of time 1; 1.5; 2.0; 2.5 and 3.0 hours. The standard solution volume of 20% U3O8 are 100; 300; 500; 700 µL with variation of electrolyte buffer solution NH4Cl, NH4OAc, NH4HSO4 dan (NH4)2SO4. The result of electrodeposition process showed that optimum condition electrodeposition process for 235U isotope was obtained currents 1.2 ampere with process time for 2 hours, and 300 µL volume feed with electrolyte buffer NH4HSO4 in pH 3,5. The results of the electrodeposition process was obtained 2.314 µg deposition of the isotope 235U with recovery of 99.91%. The condition optimum parameter above was used for electrodeposition process in determination of 235U isotope which contained in U3Si2/Al irradiated fuel element. The spectrometer alpha analysis was obtained weight of 235U isotope as 0.403 µg with recovery of 91.80%. The conclusion of this research, the electrodeposition methods is good enough to be used for determining 235U isotope in U3Si2/Al irradiated fuel plate.
PENGARUH TEMPERATUR DAN IRADIASI TERHADAP INTERDIFUSI PARTIKEL BAHAN BAKAR JENIS U−7Mo/Al Maman Kartaman Ajiriyanto; Aslina Br. Ginting; Supardjo; Boybul Boybul
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 1 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.1.2740

Abstract

U−7Mo/Al alloy had great potential as research reactor fuel, but it had several disadvantages, such as, it can form a interaction layer at the interface during the process of fabrication and irradiation in a reactor. The research objective was determining the interaction layer that was caused by interdiffusion or diffusion couple of U−7Mo with AlMg2 alloy which was annealed at 500 °C and 550 °C for 24 hours. The observation of microstructure used a Scanning Electron Microscope (SEM) on diffusion couple sample which was heated at temperature of 500 °C had not seen the layer interaction or the formation of a new phase between particles of U−Mo and Al matrix, but heating treatment at 550 °C indicated that U−7Mo alloy had been interdiffusion with AlMg2 plate produced (U,Mo) Alx compound on the interfaces. It was evidenced by interdiffusion reaction analysis used DTA that showed that U−7Mo / Al alloy at 500 °C had good heat compatibility, but at temperatures upper than 550 °C it had been phase changed from a + d to a + g phase. The heating in DTA furnace up to 679.14 °C produced U(Al,Mo)x meta stable phase and then interdiffusion process with uranium molten formed layer interaction that formed UAlx compound agglomerates (UAl4, UAl3 and UAl2). Agglomerates was formed from the heating process which was similar to agglomerates that caused by irradiation. U−7Mo / Al Fuel alloy that had 58% burn up had been interdiffusion between U−7Mo with Al matrix produced U(Al,Mo)x metastable phase that turned into (U, Mo) Al7 layer, UMo2Al20 precipitates, (UMo)Al3−Al and formed a boundary or UAlx (UAl4, UAl3 and UAl2) agglomerates. The results of microstructure analysis used SEM and interdiffusion reactions used DTA was supported by the analysis of micro hardness used Vickers Hardness. The results of hardness analysis that was done to AlMg cladding and U−7Mo alloy (before and after heating) and diffusion couple of U−7Mo / Al samples with AlMg2 plate after heating at 550 °C were respectively 64.62 and 340.45 HV (before heating) and 52.34; 303.16 and 497.34 HV (after heating). Diffusion couple U−7Mo/Al with AlMg2 plate samples had the highest hardness value. This hardness difference showed that the interdiffusion test used diffusion couple produced a new compound (U, Mo) Alx in interface zone that had different character, but the formation of interaction layer is not expected in the fuel U−Mo / Al dispersion because micro hardness and density of (U, Mo) Alx compound’s layer was lower than the average density of U−7Mo/ Al alloy.
PENGARUH UNSUR Zr TERHADAP PERUBAHAN SIFAT TERMAL BAHAN BAKAR DISPERSI U-7Mo-xZr/Al Supardjo; Agoeng Kadarjono; Boybul Boybul; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 1 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.1.2741

Abstract

Thermal properties data of nuclear fuel is required as input data to predict material properties change phenomenon during the fabrication process and irradiated in a nuclear reactor. Study the influence of Zr element in the U-7Mo-xZr/Al (x = 1%, 2% and 3%) fuel dispersion to changes in the thermal properties at various temperatures have been stiffened. Thermal analysis includes determining the melting temperature, enthalpy, and phase changes made using Differential Thermal Analysis (DTA) in the temperature range between 30 °C up to 1400 °C, while the heat capacity of U-7Mo-xZr alloy and U-7Mo-xZr/Al dispersion fuel using Differential Scanning Calorimeter (DSC) at room temperature up to 450 °C. Thermal analyst data DTA shows that Zr levels of all three compositions showed a similar phenomenon. At temperatures between 565.60 °C – 584.98 °C change becomes α + δ to α + γ phase and at 649.22 °C – 650.13 °C happen smelting Al matrix Occur followed by a reaction between Al matrix with U-7Mo-xZr on 670.38 °C – 673.38 °C form U (Al, Mo)x Zr. Furthermore a phase change α + β becomes β + γ Occurs at temperatures 762.08 °C – 776.33 °C and diffusion between the matrix by U-7Mo-xZr/Al on 853.55 °C – 875.20 °C. Every phenomenon that Occurs, entalphy posed a relative stable. Consolidation of uranium Occur in 1052.42 °C – 1104.99 °C and decomposition reaction of U (Al, Mo)x and U (Al, Zr)x becomes (UAl4, UAl3, UAl2), U-Mo, and UZr on 1328,34 °C - 1332,06 °C , The existence of Zr in U-Mo alloy increases the heat capacity of the U-7Mo-xZr/Al, dispersion fuel and the higher heat capacity of Zr levels increased due to interactions between the atoms of Zr with Al matrix so that the heat absorbed by the fuel increase.