Yanlinastuti Yanlinastuti
Unknown Affiliation

Published : 23 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 23 Documents
Search

OPTIMASI PARAMETER PEMISAHAN Zr DALAM PEB U3Si2/Al PRA IRADIASI MENGGUNAKAN METODE KROMATOGRAFI PENUKAR ANION Yanlinastuti Yanlinastuti; Noviarty Noviarty; Iis Haryati; Syamsul Fatimah; Boybul Boybul; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 25 No. 2 (2019): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2019.25.2.5508

Abstract

Determination of optimum parameters in the process of zirconium separation from U3Si2/Al fresh fuel solution by anion exchanger chromatography and analysis with UV-Vis spectrophotometer has been carried out. Zirconium is one of isotopes that can be used in the determination of fuel burn-up. The purpose of this study is to obtain optimal parameters of zirconium separation in standard materials as well as U3Si2/Al fresh fuel solution by anion exchanger chromatography. Optimization of Zr separation parameters was carried out using Dowex 1x-8 resin with a variation in weight of 0.5; 1.0; 1.5; 2.0 and 2.5 g, acidity of H2SO4 at 1; 2; 3; 4; 5 and 6 M, standard feed concentrations of Zr at 50; 100; 150 and 200 ppm and flow rate of 3M H2SO4 elution at 0.1; 0.3; 0.5; 0.7 and 0.9 mL/minute. To the Zr effluent as the result of separation was added Arsenazo III 0.1% as complexing agent, and subsequent analysis with UV-Vis spectrophotometry was done at a wavelength of 665.3 nm. The measurement results show that the optimal parameters of Zr separation are the use of 1.5 g resin with resulting recovery of 70.79%, acidity of 3M H2SO4 with recovery of 83.94%, feed concentration of 150 ppm with recovery of 87.64% at a flow rate of 0.5 mL/minute. When those optimal parameters were used in Zr separation from U3Si2/Al fresh fuel solution, the recovery obtained was 96.23%. These optimized parameters can also be used to separate Zr from U3Si2/Al irradiated fuel solution.
PEMBUATAN STANDAR CESIUM DARI LARUTAN PEB U3Si2/Al PASCA IRADIASI DENSITAS 2,96 gU/cm3 DENGAN METODE PENGENDAPAN CsClO4 Aslina Br. Ginting; Boybul Boybul; Arif Nugroho; Yanlinastuti Yanlinastuti; Noviarty Noviarty; Gatot Wurdiyanto; Hermawan Chandra
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 25 No. 2 (2019): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2019.25.2.5457

Abstract

A considerable amount of irradiated nuclear fuel solutions exists in the hot cell area of Radiometallurgy Instalation (IRM). These solutions were generated from sampling activities for burnup test. The solutions cannot be disposed due to the present of 137Cs isotope and other heavy elements that have a long half time, but the solutions can be used as a secondary source of 137Cs standard for analysis purposes. Post-irradiation fuel analysis is always conducted by a valid method and with a calibrated spectrometer-γ. The standard used in the calibration of spectrometer-γ energy or activity is 137Cs isotope. There has been some restriction in the use of spectrometer-γ because spectrometer-γ calibration cannot be performed routinely due to the unavailability of standard sources. The availability of 137Cs isotope for R&D is still dependent on abroad suppliers. Therefore, in this research, PTBBN and PTKMR aim to develop a secondary standard source of 137Cs isotope with 10330 ± 411 Bq activity. The standard source was obtained from a solution of 137Cs separated from U3Si2/Al irradiated fuel. The separation was done by precipitation method with CsNO3 and HClO4 as the carrier. The result of the separation is 137CsClO4 precipitate, dried and weighed for obtaining greater activity and measured with a spectrometer-γ. The dried precipitate 137CsClO4 was subsequently packed as closed standard source (shield source). This standard sourced was certified by PTKMR as secondary standard isotope of 137Cs and is ready to be used for energy calibration of spectrometer-γ.
ANALISIS KOROSI PIPA PENDINGIN SEKUNDER RSG-GAS DENGAN TEKNIK ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY (EIS) Maman Kartaman Ajiriyanto; Rosika Kriswarini; Yanlinastuti Yanlinastuti; Diyah Erlina Lestari
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 24 No. 2 (2018): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2018.24.2.4421

Abstract

Multi-purpose reactor G.A. Siwabessy has a secondary cooling system facility to extract heat generated from uranium fission reactions in the reactor. The cooling pipe material is a type of carbon steel. Secondary cooling media is water supplied from Puspiptek. To extend the lifetime of the pipe, chemical compound ZnPO4 was put on the water-cooling media as a corrosion inhibitor. The corrosion analysis of secondary pipe was performed by corrosion testing using EIS and tafel method. The electrochemically corrosion test was performed with three electrode cells in water media, 0.05 M HCl solution and 3% NaCl solution. The aim is to obtain the optimum inhibitor concentration added in the secondary coolant and to determine the inhibition mechanical as well as the inhibitor efficiency. EIS testing was performed in the frequency range 100 kHz to 0.02 Hz in HCl 0,05M. Test results show changes in electrical parameters such as Rct, Cdl and Rs. The inhibitor concentration increases then Rct value increase. At inhibitor concentration of 90 ppm obtained the highest Rct value is 81,29 ohm. Efficiency of the inhibitor addition produces maximum value is 66,75% at concentration of 90 ppm. The corrosion rate in samples on medium of 3% NaCl without inhibitor, moss inhibitor and corrosion inhibitor were 3.975, 3.576 and 3.215 mpy respectively. The addition of a mixture of corrosion inhibitors and moss inhibitors can decrease the corrosion rate up to 1.586 mpy quantitatively. The addition of inhibitors using ordinary water may inhibit interface reactions on the surface of the sample as indicated by the higher the inhibitor concentration the higher the Rct value. In NaCl 3% medium also shows the same phenomenon relatively that the corrosion mechanism can be inhibited by increasing of Rct value as well as in this condition, Rs value is constant relatively. The dominant fact that the addition of a corrosion inhibitor could decrease the corrosion rate. The moss inhibitors have a primary function not to decrease the corrosion rate.
KARAKTERISASI PADUAN AlMgSi UNTUK KELONGSONG BAHAN BAKAR U3Si2/Al DENSITAS URANIUM 5,2 gU/cm3 Aslina Br. Ginting; Supardjo; Yanlinastuti Yanlinastuti; Dian Anggraini; Boybul Boybul
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 24 No. 1 (2018): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2018.24.1.4016

Abstract

Increase in uranium density from 2.96 gU/cm3 to 5.2 gU/cm3 of U3Si2/Al fuel requires a compatible cladding. High density fuel possesses high hardness value, and the use of AlMg2 as cladding material may cause dog bone during rolling process. In addition to dog bone phenomena, swelling can also occur during the use of nuclear fuel in the reactor due to rising in fission products and burn up. For this reason, substitution of cladding material should be determined to suit the high density U3Si2/Al fuel. This research deals with the characterization of AlMgSi as a candidate for AlMg2 substitution. The characterization includes thermal analysis with DTA (Differential Thermal Analysis) dan DSC (Differential Scanning Calorimetry), hardness test with macrohardness tester, microstructure examination with SEM (Scanning Electron Microscope), and corrosion analysis by heating at 150 °C for 77 hours in an autoclave. Analysis results show that both AlMgSi and AlMg2 share stable heat compatibility with U3Si2/Al up to 650 °C. AlMgSi cladding has a hardness value of 115 HVN, higher than that of AlMg2, which is 70.1 HVN. Microstructure examination shows that AlMgSi has better morphology of interface bonding than AlMg2. Corrosion rate analysis also indicates that AlMgSi has lower corrosion rate. The results of thermal, hardness, microstructure and corrosion characterization reveal that the U3Si2/Al fuel of 5.2 gU/cm3 suits better with AlMgSi than AlMg2.
PENGARUH TEMPERATUR DAN KOMPOSISI Nb TERHADAP INTERDIFUSI PADUAN U-Zr-Nb Maman Kartaman Ajiriyanto; Masrukan; Fajar Al Afghani; Yanlinastuti Yanlinastuti
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 3 (2021): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.3.6503

Abstract

A simulation of U-Zr-Nb intermixed fuel has been carried out with aluminum plates. Initially, U-6Zr-2Nb, U-6Zr-5Nb, and U-6Zr-8Nb alloy ingots were made using an electric arc melting furnace. The ingot obtained was cut into pieces with a thickness of 2-3 mm and a diameter of about 5-6 mm, then it was covered Al plate on one side and pressed. After pressing, the alloy ingots of U-6Zr-2Nb, U-6Zr-5Nb, and U-6Zr-8Nb were heated at temperatures of 350 and 450 oC for 1 hour. The ingot was subjected to several tests, namely microstructure examination using optical microscope and Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectrometer (EDS), hardness test using microhardness tester, and phase observation using X-ray diffractometer (XRD). The results of microstructure examination show that the boundaries between the U-6Zr-2Nb, U-6Zr-5Nb, and U-6Zr-8Nb layers (interfaces) and the Al layer were clearly visible. The higher of the Nb content, the denser the interface between the two layers. For the microhardness test, we found that the hardness at the interface was difficult to measure, while the U-Zr-Nb region shows an increase in hardness for heating from 350 to 450 oC, while in the Al section there is a decrease in hardness when the heating temperature increases from 350 to 450 oC. UO3 compounds were formed in all test samples while the γ-U phase was formed in U-6Zr-2Nb samples both heated at temperatures of 350 and 450 oC.
OPTIMASI PARAMETER METODE PEMISAHAN RADIONUKLIDA 95Zr DALAM LARUTAN PELAT ELEMEN BAKAR U3Si2/Al TERIRADIASI Yanlinastuti Yanlinastuti; Noviarty Noviarty; Iis Haryati; Ariyanti Saputri; Boybul Boybul; Supardjo
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 3 (2021): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.3.6535

Abstract

Radionuclide of 95Zr is one of the γ-radiation emitter radionuclides which has a short half-life so that it can be used as an indicator of burn up. In the irradiated U3Si2/Al fuel element plate there are several radionuclides of fission products emitting α, β and γ and when measuring radiation using γ-spectrometry, these radionuclides may interfere with each other resulting in inaccurate measurement results. Therefore, it is necessary to separate 95Zr for better accuracy in the measurement of γ-radiation with a γ-spectrometer. The purpose of this study was to obtain the optimum parameters for the separation of 95Zr in U3Si2/Al fuel element plate solution by ion exchange column method using Dowex 1x-8Cl- resin of 100-200 mesh in diameter. The optimum parameters obtained were then used for the separation of 95Zr in a solution of irradiated U3Si2/Al fuel element. It was found that the optimum parameter of acidity of H2SO4 in the feed was a concentration of 0.5 M, and the acidity of H2SO4 for elution was 1.0 M with a recovery of 98.20%. The weight of the resin to bind 95Zr radionuclide was 2.0 g with a recovery of 78.76%. The required feed volume was 50 µL with a recovery of 96.90% and the optimized flow rate was 0.1 mL/minute with a recovery of 96.72%. The optimum values were used for the separation of the U3Si2/Al fuel element plate solution irradiated with the code of Bottom (B), Middle (M) and Top (T). The measurement results show that the mean recovery of separation was 95Zr for code B-1 = 75.078%; B-2= 81.401%; M1=76,850%; M-2=83.806%; T-1=84.433%; and T-2 = 81.728% with the acceptability of the CV repeatability value smaller than the CV Horwitz value.
PEMISAHAN CESIUM DALAM BAHAN BAKAR U3Si2/Al DENSITAS 4,8 gU/cm3 BURN UP 60% POTONGAN BOTTOM Ariyanti Saputri; Sutri Indaryati; Iis Haryati; Yanlinastuti Yanlinastuti; Hanifah Rifaatul Mahmudah; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 3 (2021): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.3.6571

Abstract

The separation of cesium in U3Si2/Al fuel with a density of 4.8 gU/cm3 and 60% burn up by cation exchange using zeolite from Lampung has been carried out. Cesium isotope is used as a burn-up indicator for irradiated nuclear fuel. The separation aims to obtain an accurate cesium weight so that the calculation of burn up by the destructive method can be carried out correctly. The fuel plate of U3Si2/Al was cut in duplicates at the bottom with a weight of B-1=0.036 g and B-2= 0.037g, respectively. The fuel plate of U3Si2/Al with this weight was then dissolved using 6N HCl and 6N HNO3 in 10 mL. The solution of U3Si2/Al was then pipetted 1 mL and transferred from the hot cell to R.135 and diluted to 25 mL. The solution was pipetted 50 µL into a vial in duplicates and 1000 mg of Lampung zeolite was added. Separation process of 134Cs and 137Cs from 235U was done by cation exchange for 60 minutes. The results obtained were isotopes 134Cs and 137Cs in the solid phase while uranium (238U, 235U, 234U) and other isotopes in the liquid phase. The weight of the isotopes of 134Cs and 137Cs was then measured using a spectrometer/g. The weight of the isotopes of 137Cs and 134Cs in solution at Bottom position was B-1=0.00003283 g/0.036g and B-1= 0.000000147 g/0.036 g for 137Cs and 134Cs respectively while another duplicate was B-2=0.00003290 g/0.037g for 137Cs and B-2=0.000000222 g/0.037g for 134Cs. It can be concluded that in the separation of cesium in 50 µL solution of U3Si2/Al at Bottom position by cation exchange using 1000 mg of zeolite from Lampung, good results were obtained.
PENGARUH PENAMBAHAN ION SULFAT TERHADAP REKOVERI PEMISAHAN URANIUM MENGGUNAKAN METODE KOLOM PENUKAR ANION Boybul Boybul; Yanlinastuti Yanlinastuti; Dian Anggraini; Aslina Br. Ginting; Arif Nugroho; Rosika Kriswarini
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 3 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.3.3679

Abstract

In the previous research, it was observed that the recovery of uranium separation by anion exchange column method with HCl 12 N solvent was 68.2137 %. The recovery can be increased by optimizing the uranium separation parameters by the use of HCl and Na2SO4 solvent mixture. A 500 μL uranyl nitrate standard solution was used as feed with varied HCl concentration of 6 N, 9 N, 12 N and varied Na2SO4 concentration of 500, 1000, 1500, 2000, 2500 and 3500 ppm as reagent solution. In the anion exchange process, uranium was bound by the resin to form [UO2(SO4)3]4- and [UO2(SO4)2]2 complex compounds, and these complexes were eluted with 15 mL of 0.15 N HCl dilute solution. The eluate was heated to nearly dried condition and 1 mL of HCl concentrated solution was added for electrodeposition process. The uranium deposited on stainless steel planset, as the result of electrodeposition process, was analyzed with alpha spectrometer. It was observed that the largest 235U content was found in 9M of HCl solvent and 1500 ppm of Na2SO4 with 95.7124 % recovery. Therefore, the concentration value of HCl of 9 N and 1500 ppm of Na2SO4 were subsequently applied to the uranium separation of irradiated U3Si2/Al fuel element plate. An amount of 500 μL supernatant of U3Si2/Al specimen taken from the top, middle and bottom position of fuel element plate (FEP) were put into an anion exchange column containing 1 g of Dowex-Cl resin. The results of the separation process were 235U isotope identified according to their position in the irradiated U3Si2/Al fuel element plate i.e. top, middle, and bottom. It was found that the recovery values were 13265.7866 μg/gFEP; 6923.9248 μg/gFEP; and 12332.4175 μg/gFEP representing their position of top, middle and bottom respectively. It is concluded that the use of 9M of HCl solvent and 1500 ppm of Na2SO4 by anion exchange column method can improve uranium separation recovery from 68.2137 % to 95.7124 %.
PENGARUH PELARUT ORGANIK PADA PROSES PERTUKARAN ANION DALAM PEMISAHAN URANIUM DARI LARUTAN PEB U3Si2/Al PASCA IRADIASI Dian Anggraini; Boybul Boybul; Yanlinastuti Yanlinastuti; Arif Nugroho; Rosika Kriswarini; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 2 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.2.3576

Abstract

Separation method of uranium from nuclear fuel solutions was developed to improve the quality of uranium-based analysis of post-irradiation nuclear fuel. The aim of this study was to determine the effect of organic solvent on the anion exchange process on the recovery of U from U3Si2/Al fuel solution post-irradiated. The organic solvent, in this case methanol, contained in solvent medium in the anion exchange column may be possible to increase the resin sorption of the uranium. The materials used are standard solution of uranil nitrat and supernatant solution of Cs separation process from the fuel solution. The uranium separation method from U3Si2/Al post irradiated fuel solution uses two columns of anion exchanger with two stages. The first column uses Dowex 1x8-Cl Dowex resin. Parameters varied in the first column are HNO3 concentrations ranging from 1M; 2M; 3M and 4M. The parameters variation in the second column is the ratio of HCl/methanol volume of 30:70 %; 20:80 % and 10:90 %. The result obtained a maximum U recovery of 90,68 % with feed solution composition in the first column containing 3 % HNO3 and methanol by 50 %volume, while in the second column with 6M HCl composition with methanol in 10 %:90 % ratio. In these conditions obtained uranium content in a solution of the middle PEB U3Si2/Al TMU 2.96 g/cm3 piece of 0.4725 μg.
ANALISIS KANDUNGAN CESIUM DAN URANIUM DALAM BAHAN BAKAR U3Si2/Al PASCA IRADIASI Boybul Boybul; Yanlinastuti Yanlinastuti; Arif Nugroho; Dian Anggraini; Rosika Kriswarini; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 2 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.2.3568

Abstract

Separation of fission product isotopes of 137Cs and 235U has been done to determine content of 137Cs and 235U in irradiated U3Si2/Al fuel plate of 2.96 gU/cm3 density. The initial step in the determination of 137Cs and 235U content is sample cutting process. The cutting position was determined at the top middle and bottom part of the plate by an amount of 0.095 g; 0.1103 g and 0.1441g for each respective position. Each sample was dissolved in 25 mL of HNO3 6N dan HCl 6N to obtain irradiated U3Si2/Al solution. Separation was carried out by cation exchange and precipitation methods. The separation of 137Cs was done by pipetting 150 µL of the irradiated U3Si2/Al sample solution and adding it to 1000 mg of Lampung zeolite, while the separation by precipitation method was done by adding 700 mg of CsNO3 powder as carrier and HClO4 to the U3Si2/Al sample solution. In the cation exchange method, 137Cs would be bound by zeolite in the solid phase in the form of 137Cs-zeolite and uranium would stay in the liquid phase or supernatant. The precipitation was done in an ice bath at -4 oC to obtain 137CsClO4 precipitate. The effluent leaving the column was subjected to electrodeposition process for 235U content measurement with α-spectrometer. The 137Cs content obtained by cation exchange was 401.0335 µg/g FP (FP = irradiated fuel plate); 451.1094 µg/g FP and 343.9651 µg/g FP for each respective sample position by 99 % recovery, while the 137Cs content obtained by precipitation method was 393.4581 µg/g FP; 452.0525 µg/g FP and 330.7839 µg/g FP for each respective sample position by 98 % recovery. The 235U content was found to be 45208 µg/g FP; 50896 µg/g FP and 44336 µg/g FP for each respective sample position by 68 % recovery.