Yanlinastuti Yanlinastuti
Unknown Affiliation

Published : 23 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 23 Documents
Search

PEMISAHAN DAN ANALISIS 137Cs DARI LARUTAN PELAT ELEMEN BAKAR U-7%Mo/Al Dian Anggraini; Noviarty Noviarty; Yanlinastuti Yanlinastuti; Aslina Br. Ginting; Rosika Kriswarini; Arif Nugroho; Boybul Boybul
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 3 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.3.3183

Abstract

The aim of this research is to get a valid method of separating cesium from U-7Mo/Al fuel plate solution through determination of parameter of method (accuracy, precision, and recovery). Precipitation method and cation exchange method that are used refer to standard ASTM 690-000 and research result of U3Si2/Al. Parameter method determination has been done by using 150 μL sample (U-7%Mo/Al fuel plate solution, 50 μL of standard solution in 2 mL of HCl 0,1 N. The sample solution was undergone precipitation process by using HClO4 concentrated and 225 mg of CsNO3 as carrier in temperature 0oC for an hour, while exchange cation process was done by using 400 mg of resin zeolite Lampung. The analysis of 137Cs in CsClO4 and 137Cs - zeolite was done by gamma spectrometer. Determination of recovery method was done by comparing count value of 137Cs before and after separation process. Recovery of precipitation method was obtained 95.56 % with accuracy and precision measurement of 0.375 % and 1.875 % respectively, while recovery of cation exchange method obtained 26.73 %. To sum up, the results show that precipitation method better than exchange cation method for separation 137Cs from U-7Mo/Al fuel plate solution.
KORELASI KOMPOSISI UNSUR TERHADAP SIFAT TERMAL SERBUK BAHAN BAKAR U-ZrHX Masrukan; M. Husna Alhasa; Yanlinastuti Yanlinastuti
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 2 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.2.3090

Abstract

Analysis has been conducted to determine the composition correlation on the thermal properties of the powder fuel U-ZrHx. U-ZrHx powder made from the process hydriding U-Zr ingot, where the ingot is the result of U-Zr and Zr U metal melting. In this experiment made three variations of powders, namely U-35ZrHx, U-45ZrHx, and U-55ZrHx. Need for determination of the thermal properties of Zr was to determine the effect of the nature of the transformation of Zr levels of heat from the fuel. At first, U and Zr metal is melted in electric arc furnaces to produce ingot U-Zr. U-Zr ingot then made powder with hydridring-milling techniques to produce U-Zr powder. U-Zr powder composition analyzed using techniques spectroscopy atomic absorption (AAS) and UV-Vis spectroscopy. The results of composition analysis showed that the analysis to determine the content of U and Zr nearly all the test samples analyzed have quite a big difference between the content of U and Zr as determined by the results of the analysis of U and Zr exception analysis result in powder U-45Zr which differ only 0.609%. From the analysis of impurities obtained that nearly all the impurities that exist still meet the requirements for fuel unless the elements Fe, where elements of the existing Fe amounted to 382.912 g/g while the requirement of £ 250 mg /µg. Testing conducted heat capacity in the temperature range 35 ° C to 437 ° C showed that the capacity were greatest powder 35ZrHx U-with a value heat capacity of 0.13 J / g.oC. Meanwhile, test results obtained transition phase change that the U-45ZrHx undergo two stages of reaction with phase change. It can be concluded when seen from the content of U and Zr cannot be used for fuel, while the analysis of the content of impurities found that all the elements that are still eligible for the fuel unless the element Fe. For the analysis of the thermal properties are the heat capacity of the heat capacity of the highest values obtained in powder U-35ZrHx, while the transition from the testing phase changes shows that the U-45ZrHx undergo two stages of reaction with phase change. There is an effect of the composition on the thermal properties, where the higher the content of Zr, the value of uranium zirconium hydride heat capacity is lower.
PENGARUH PARAMETER PROSES ELEKTRODEPOSISI TERHADAP PENENTUAN BERAT ISOTOP 235U DALAM PEB U3Si2/Al PASCA IRADIASI Yanlinastuti Yanlinastuti; Boybul Boybul; Aslina Br. Ginting; Dian Anggraini
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 2 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.2.3093

Abstract

Electrodeposition process for determination of 235U isotope is affected by current, contact time, feed volume and type of buffer solution. The aim of this research is to obtain optimum parameter of electrodeposition process for 235U determination in U3Si2/Al irradiated fuel plate. Electrodeposition process is done by some variation of parameters, that are the current 1; 1.2; and 1.4 ampere with variation of time 1; 1.5; 2.0; 2.5 and 3.0 hours. The standard solution volume of 20% U3O8 are 100; 300; 500; 700 µL with variation of electrolyte buffer solution NH4Cl, NH4OAc, NH4HSO4 dan (NH4)2SO4. The result of electrodeposition process showed that optimum condition electrodeposition process for 235U isotope was obtained currents 1.2 ampere with process time for 2 hours, and 300 µL volume feed with electrolyte buffer NH4HSO4 in pH 3,5. The results of the electrodeposition process was obtained 2.314 µg deposition of the isotope 235U with recovery of 99.91%. The condition optimum parameter above was used for electrodeposition process in determination of 235U isotope which contained in U3Si2/Al irradiated fuel element. The spectrometer alpha analysis was obtained weight of 235U isotope as 0.403 µg with recovery of 91.80%. The conclusion of this research, the electrodeposition methods is good enough to be used for determining 235U isotope in U3Si2/Al irradiated fuel plate.