Garuda - Garba Rujukan Digital

Perbandingan Karakteristik Campuran Cold Paving Hot Mix Asbuton (CPHMA) yang Dipadatkan Secara Dingin dan Panas Thanaya, I Nyoman Arya; Suweda, I Wayan; Sparsa, A.A. Adi
Jurnal Teknik Sipil Vol 24, No 3 (2017)
Publisher : Institut Teknologi Bandung

AbstrakCold Paving Hot Mix Asbuton (CPHMA) adalah campuran yang terdiri dari agregat, asbuton butir, bahan peremaja dan bahan tambah lain yang dicampur panas dipadatkan dingin (pada temperatur ruang 30Â°C). Karakteristik campuran dipengaruhi temperatur pemadatan. Tujuan penelitian ini adalah untuk memperoleh: kadar aspal residu optimum, temperatur pemadatan ideal dan perbandingan karakteristik CPHMA yang dipadatkan secara dingin dan panas. Pemadatan dilakukan pada suhu 30Â°C, 60Â°C, 90Â°C, 120Â°C, dan 150Â°C. Diperoleh hasil, kadar aspal residu optimum 7 %; suhu pemadatan ideal 90Â°C. Pemadatan dibawah suhu 90Â°C memberikan porositas lebih tinggi berkisar antara (4,86-5,53)% namun masih memenuhi spesifikasi (4-10%). Pemadatan diatas suhu 90Â°C memberikan porositas antara (2,04-3.0)%, yang lebih rendah dari spesifikasi. CPHMA yang dipadatkan pada suhu ideal 90Â°C memberikan karakteristik Marshall, cantabro, kekakuan (stiffness), rangkak (creep), dan kelelahan (fatigue) lebih baik dibandingkan dengan CPHMA yang dipadatkan dingin.AbstractCold Paving Hot Mix Asbuton (CPHMA) is a mixture that consists of aggregates, asbuton particles, rejuvenating materials and other added materials, which were hot mixed and compacted cold (at ambient temperature 30Â°C). The characteristics of the mixture were affected by compaction temperatures. The objectives of this study were to obtain: residual optimum asphalt content; ideal compaction temperature and characteristics comparison of CPHMA compacted cold and hot. Compaction were carried out at 30Â°C, 60Â°C, 90Â°C, 120Â°C and 150Â°C. It was obtained that the optimum residual asphalt content for CPHMA mixture was 7% and the ideal compaction temperature was 90Â°C. Compaction at temperature lower than 90Â°C gave higher porosity, i.e between (4.86-5.53)%, nonetheless still met specification (4-10)%. Compaction at higher than 90Â°C gave porosity between (2.04-3.0)% which were lower than the specification. CPHMA compacted at ideal 90Â°C gave better Marshall characteristics, cantabro, stiffness, creep, and fatigue, compared to the cold compacted CPHMA.

ANALISIS KELAYAKAN FINANSIAL ANGKUTAN TIRTAYATRA BALI - JAWA TIMUR I Wayan Suweda; I Gede Putu Udiana Putra
JURNAL SPEKTRAN Vol 7 No 1 (2019): Vol. 7, No.1, Januari 2019
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (506.929 KB)

FINANCIAL ANALYSIS OF BALI-EAST JAVA TIRTAYATRA TRANSPORTATION ABSTRACT Bali, with its predominantly Hindu, has experienced a fairly rapid development of the tourism sector. With personal awareness and supported by the better economic condition, the Balinese Hindu people are able to religious travel (tirtayatra) to other areas. Travel Companies catch this opportunity by opening travel packages to several temples in East Java. This study aims to analyze the level of financial investment feasibility in the tirtayatra transportation business. Feasibility of investment can be obtained by comparing the variables of benefit and cost. Analysis of the level of feasibility is determined by applying the NPV, IRR and BCR methods and sensitivity analysis. Data used, both primary and secondary, are obtained from several Travel Companies in Bali. From the results it can be concluded that the investment of the Tirtayatra package Bali - East Java is a package that continues to grow. In the feasibility analysis that is served by 3 medium bus and the vehicles economic life of 7-year, the Present Value of benefit is Rp. 11,891,301,439 and the Present Value of cost is Rp. 11,335,305,821. Therefore, the result gives the value of NPV Rp.555,995,618 > 0, BCR = 1.0490 > 1 and IRR = 27.63% > i (17%). Thus the investment at religious travel can be considered feasible. However, this package will be inappropriate if the annual interest rate passes the value of 27.63%.

ANALISIS KINERJA DAN PENGEMBANGAN PELABUHAN LAUT DI BALI (STUDI KASUS: PELABUHAN CELUKAN BAWANG) Kadek Arisena Wikarma; I W Suweda; I G. Putu Suparsa
JURNAL SPEKTRAN Vol 4 No 1 (2016): Vol. 4, No. 1, Januari 2016
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

Abstract: Celukan Bawang Harbour is located in the northern province of Bali. Port traffic through the Celukan Bawang Harbour during the period of 2005-2009 has decreased. So It is necessary for the performance evaluation of the port so that the reduction in traffic flows of goods can be determined. In addition, this study also predict traffic flow of goods 30 years future so it can be evaluated development of the port in the future . The evaluation was done based on the performance data Celukan Bawang Harbour last 10 years. Then a prediction of traffic flows to goods the next 30 years using multiple linear regression analysis. For the evaluation of the development of the port to analyze the financial feasibility of the port master development plan (RPIP) 10 years from 2014 to 2023 years that compare to the development plan based on a prediction of traffic flows. Based on the evaluation of operating performance, port obtained poor performance. This is evident from the performance indicators in 2013 that the waiting time: 58 hours and BOR value: 88 % above the standard value is specified, while the percentage of effective time / Berthing time: 31.6%, SOR: 6%, Yor: 0% is far below the standard set value. Meanwhile, if the predicted assuming port performance has been improved, the traffic flow of goods grew 10.90% annually. Financial analysis based RPIP port development is not feasible to get the value NPV = -1,521,941,710 BCR value = 0.9828 and a IRR = 11.46%, while the development of port based traffic flow prediction goods with the sensitivity condition cost increase 15% and benefits decrease 15% get decent results with NPV = 12,191,952,255 and BCR value = 1.4546.

ANALISIS PEMBEBANAN LALU LINTAS PADAPERENCANAAN JALAN-JALAN PERINTIS I Wayan Suweda
JURNAL SPEKTRAN Vol 6 No 1 (2018): Vol. 6, No. 1, Januari 2018
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (398.414 KB)

Nusa Penida (20,284 ha) is nearly 2x the areas of the other three districts of Klungkung regency,which located in the Bali mainland (11,216 ha). However, the condition of people is very underdeveloped. The regionsdisparityis caused by various factor, one of them is "isolated" area of ??Nusa Penida. So,itsneed to be planned a pioneering road to improve accessibility. In the prediction of traffic assignment, of course, can not be based solely on the existing very small trip generation. For that ananalogous method should be set up to the region that has the same characteristics. Analogy method was developed through a comparative study to other areas of Bali with a similar limestone structure, the same road networkand tourist areas. In accordance with development plan, it can be predicted that the road ADT in 2020 will be 5,800.62 pcu/day and DHV725.08 pcu/hour. Meanwhile, the end of the road horizon-year 2045 reaches 37,576.31 pcu/day with DHV of 4,697.05 pcu/hour. Assuming that of the rural environment, the capacity of the 2/2UD hilly road is 2,910 pcu/hour. Therefore, from the loading analysis shows that in the year of 2038 the road should be widened to be 4 lanes to serve the-2traffic directions. Keywords:pioneer road, analogy method, nusa penida

ANALISIS PEMBEBANAN LALU LINTAS PADA JALAN LINGKAR IBU KOTA KECAMATAN (IKK) NUSA PENIDA BERBASIS RENCANA DETAIL TATA RUANG (RDTR) I Wayan Suweda; I Putu Bela Yusdiantika
JURNAL SPEKTRAN Vol 8 No 2 (2020): VOL. 8 NO. 2, JULI 2020
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

Show Abstract | Download Original | Original Source | Check in Google Scholar

ABSTRAK Berdasarkan hasil survai tahun 2014, kecepatan perjalanan rata-rata segmen terkrusial di jalan utama Ibu Kota Kecamatan (IKK) Nusa Penida hanya 23,61 km/jam akibat tingginya intensitas parkir di tepi jalan serta belum tersedia rute alternatif. Pemerintah Kabupaten Klungkung telah merencanakan tata guna lahan (TGL) di IKK Nusa Penida dengan membuat Rencana Detail Tata Ruang (RDTR) dan jalan lingkar untuk memindahkan lalu lintas menerus. Jalan lingkar serta TGL yang direncanakan dalam RDTR diasumsikan beroperasi tahun 2020. Penelitian ini menganalisis beban lalu lintas total pada jalan lingkar yang terdiri dari volume lalu lintas yang dihasilkan TGL dan volume lalu lintas menerus sehingga jumlah lajur (kapasitas jalan) cukup agar tingkat pelayanan jalan tidak kurang dari level C sampai akhir umur rencana jalan tahun 2040. Data yang digunakan berupa tingkat bangkitan perjalanan dari tiap tipe TGL, data pencacahan lalu lintas, waktu tempuh kendaraan dan asal-tujuan perjalanan. Data survai diperoleh tahun 2018. Volume lalu lintas yang membebani jalan lingkar IKK Nusa Penida pada jam puncak tahun 2020 terdiri atas; 1) volume lalu lintas menerus hasil persamaan Moskowitz untuk jarak dan waktu yang dihemat sebesar 207,11 smp/jam; 2) bangkitan lalu lintas dari TGL (lalu lintas lokal) sebesar 346,56 smp/jam, sehingga total beban lalu lintas adalah 553,67 smp/jam. Total beban lalu lintas bervariasi bergantung pada tingkat pertumbuhan yang dipilih. Berdasarkan tingkat pertumbuhan rendah jumlah lajur 2/2 UD cukup sampai dengan akhir umur rencana, namun untuk pertumbuhan sedang dan tinggi diperlukan 4/2 D mulai tahun 2035.

TIME HEADWAY ANALYSIS TO DETERMINE THE ROAD CAPACITY I Wayan Suweda
JURNAL SPEKTRAN Vol 4 No 2 (2016): Vol. 4, No. 2, Juli 2016
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

ABSTRACT: In developed countries, road capacity values derived from time headway is in accordance to their local traffic characteristics. In theory, time headway standards are developed using statistics models. These standards however, are not necessarily relevant to use in Indonesia. This is because of the differences in traffic conditions and motorists behaviours between those in developed countries and Indonesia. This study is to develop the time headway distribution model and subsequently to determine lionk-road capacity in the city of Denpasar, Bali Province. The study consists of time headway data analysis, model calibration and validation and road capacity values??determination. The study found that normal distribution model fitted the local traffic conditions. Road capacity values are of 2,466 pcus/hour and 2,900 pcus/hour obtained from time headway model and the Indonesian Road Capacity Manual (MKJI) respectively.

ANALISIS KARAKTERISTIK CAMPURAN ASPAL EMULSI DINGIN (CAED) DENGAN EPOXY SEBAGAI BAHAN TAMBAH I Gde Wikarga; I Nyoman Arya Thanaya; I Wayan Suweda
JURNAL SPEKTRAN Vol 5 No 2 (2017): Vol. 5, No. 2, Juli 2017
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (832.724 KB)

One of asphalt mixture being developed is Cold Bituminous Emulsion Mixtures (CBEMs) that its performances need to be improved. Within this experiment it is done by adding epoxy. The objective of this study was to analyze the characteristic of CBEMs with and without epoxy. Epoxy variation was 1%, 3%, and 6% by weight of residual bitumen. The epoxy was mix with hardener in ratio 1:3, then mixed with bituminous emulsion. Epoxy was added into the Optimum Residual Bitumen Content (ORBC) of 7,5%. The aggregate was dampened with water first then mixed with emulsion that had been added with epoxy, then compacted. It was found that CBEMs added with 1% and 3% epoxy met the specifications, however CBEMs with 6% of epoxy did not, because the porosity was 17,83% (spec.5%-10%). The soaked stability of the mixture without and with epoxy 3% was 1177,02 kg and 1416,47 kg. Addition of 3% epoxy increase soaked stability up to 20%. In stiffness, creep, and fatigue tests, CBEMs without epoxy compared by CBEMs with 3% of epoxy, respectively gave result: stiffness 1854 MPa: 959 MPa (-48,27%); strain at 106 loads repetition (Nf) was 78,09 µ?: 93,22 µ? (+19,38%); Nf at strain 100 µ? was 358.897 times: 539.585 times (+50,35%); creep slope was 23,752: 39,939 (sample was collapsed before 3600 loads repetition). However, epoxy caused the mix stiffer hence increase the porosity of the mixture to 20%. It is suggested to reduce the hardener content of the epoxy, to manitain workability and reduce porosity. Keyword: CBEMs, epoxy, stiffness, fatigue, creep

ANALISIS KINERJA JALAN PADA RENCANA PELEBARAN JALAN IMAM BONJOL DENPASAR Putu Asih Anggarini; Putu Alit Suthanaya; I Wayan Suweda
JURNAL SPEKTRAN Vol 6 No 2 (2018): Vol. 6, No. 2, Juli 2018
Publisher : Master of Civil Engineering Program Study, Faculty of Engineering, Udayana University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (197.066 KB)

ABSTRAK Jalan Imam Bonjol Denpasar yang termasuk dalam ruas jalan nasional Denpasar – Tuban merupakan salah satu jalan arteri primer yang memiliki peranan penting dan padat lalu lintas. Pesatnya perkembangan tata guna lahan di sekitar jalan ini serta tingginya volume lalu-lintas yang melewati ruas jalan ini berakibat pada menurunnya tingkat pelayanan jalan sehingga sering menimbulkan kemacetan. Sebagai solusi dari masalah tersebut, pemerintah merencanakan peningkatan kapasitas jalan melalui pelebaran jalan Imam Bonjol, dengan menutup permukaan Tukad Teba menggunakan box culvert. Penelitian ini dilakukan untuk menganalisis kinerja jalan Imam Bonjol Denpasar tanpa dan dengan adanya pelebaran jalan. Data yang digunakan untuk analisis kinerja jalan adalah berupa data sekunder yang diperoleh dari instansi terkait. Hasil analisis menunjukkan bahwa kinerja jalan Imam Bonjol kondisi eksisting (tahun 2019) tanpa adanya pelebaran mencapai derajat kejenuhan sebesar 1,61-2,14, dengan tingkat pelayanan F pada setiap segmen. Kinerja jalan Imam Bonjol pada tahun 2019 apabila rencana pelebaran dilakukan mengakibatkan perubahan derajat kejenuhan menjadi 0,41 s.d 1,00, dengan tingkat pelayanan jalan menjadi bervariasi antara B s.d E.

Perbandingan Karakteristik Campuran Cold Paving Hot Mix Asbuton (CPHMA) yang Dipadatkan Secara Dingin dan Panas I Nyoman Arya Thanaya; I Wayan Suweda; A.A. Adi Sparsa
Jurnal Teknik Sipil Vol 24 No 3 (2017)
Publisher : Institut Teknologi Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.5614/jts.2017.24.3.8

AbstrakCold Paving Hot Mix Asbuton (CPHMA) adalah campuran yang terdiri dari agregat, asbuton butir, bahan peremaja dan bahan tambah lain yang dicampur panas dipadatkan dingin (pada temperatur ruang 30°C). Karakteristik campuran dipengaruhi temperatur pemadatan. Tujuan penelitian ini adalah untuk memperoleh: kadar aspal residu optimum, temperatur pemadatan ideal dan perbandingan karakteristik CPHMA yang dipadatkan secara dingin dan panas. Pemadatan dilakukan pada suhu 30°C, 60°C, 90°C, 120°C, dan 150°C. Diperoleh hasil, kadar aspal residu optimum 7 %; suhu pemadatan ideal 90°C. Pemadatan dibawah suhu 90°C memberikan porositas lebih tinggi berkisar antara (4,86-5,53)% namun masih memenuhi spesifikasi (4-10%). Pemadatan diatas suhu 90°C memberikan porositas antara (2,04-3.0)%, yang lebih rendah dari spesifikasi. CPHMA yang dipadatkan pada suhu ideal 90°C memberikan karakteristik Marshall, cantabro, kekakuan (stiffness), rangkak (creep), dan kelelahan (fatigue) lebih baik dibandingkan dengan CPHMA yang dipadatkan dingin.AbstractCold Paving Hot Mix Asbuton (CPHMA) is a mixture that consists of aggregates, asbuton particles, rejuvenating materials and other added materials, which were hot mixed and compacted cold (at ambient temperature 30°C). The characteristics of the mixture were affected by compaction temperatures. The objectives of this study were to obtain: residual optimum asphalt content; ideal compaction temperature and characteristics comparison of CPHMA compacted cold and hot. Compaction were carried out at 30°C, 60°C, 90°C, 120°C and 150°C. It was obtained that the optimum residual asphalt content for CPHMA mixture was 7% and the ideal compaction temperature was 90°C. Compaction at temperature lower than 90°C gave higher porosity, i.e between (4.86-5.53)%, nonetheless still met specification (4-10)%. Compaction at higher than 90°C gave porosity between (2.04-3.0)% which were lower than the specification. CPHMA compacted at ideal 90°C gave better Marshall characteristics, cantabro, stiffness, creep, and fatigue, compared to the cold compacted CPHMA.

Determining the Characteristics of Trips Generated on Southern Bali using Category Analysis I Wayan Suweda; Achmad Wicaksono; Indrasurya Budisatria Mochtar
IPTEK The Journal for Technology and Science Vol 22, No 4 (2011)
Publisher : IPTEK, LPPM, Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j20882033.v22i4.78

Southern Bali, a tourism center of Indonesia, has been rapidly developed. Unfortunately, the development is not followed simultaneously by the development of adequate transportation network, as a result, traffic congestion are inevitably occurred along every urban road in the district. Therefore integrated development and regional transport planning therefore, is urgently required. In this study, trip generation is determined using Category Analysis. It is Figured out from the household based interview that Denpasar Barat zones are found to have the largest trip generation while Pecatu zones are found to be the smallest. Most of the household trips generated use private vehicles (94.95%) and the rest uses public transport. This also indicates that public transport services in Southern Bali still need to be developed.

Title

Found 10 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 10 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 10 Documents
Search