Claim Missing Document
Check
Articles

Found 9 Documents
Search

Identifikasi Fasa pada Sintesis Al2O3 dengan Metode Logam-Terlarut Asam Dianita Wardani; Suminar Pratapa
Jurnal Sains dan Seni ITS Vol 3, No 2 (2014)
Publisher : Lembaga Penelitian dan Pengabdian Kepada Masyarakat (LPPM), ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2738.996 KB) | DOI: 10.12962/j23373520.v3i2.6789

Abstract

Telah dilakukan sintesis serbuk Al2O3 dengan metode logam-terlatur asam dengan variasi temperature sintesis. Bahan dasar yang digunakan dalam penelitian ini adalah serbuk aluminium (Al Merck) dan larutan HCl (Merck 37%). Sintesis Al2O3 ini dilakukan dengan menggunakan metode logam-terlarut asam dengan waktu kalsinasi 1 jam pada variasi temperatur 100°C, 300°C, 900°C, 1000°C, dan 1100°C. Karakterisasi dan analisis fasa dilakukan dengan instrumen X-Ray Diffractometer (XRD). Analisis fasa meliputi identifikasi fasa dan tingkat kristalinitas. Hasil analisis menunjukkan bahwa pada temperatur pengeringan terbentuk kloraluminit AlCl3H12O6 yang kemudian terdekomposisi membentuk fasa amorf, lalu fasa-fasa intermediat alumina, sampai pada temperatur 1100 ̊C terbentuk fasa stabil α-Al2O3 (korundum).
Prototype Robot Transformer (Laba-Laba Delapan Kaki menjadi Silinder): Robotic Roni Novison; Dianita Wardani; Antony Antony
Jurnal Elektro dan Mesin Terapan Vol. 5 No. 1 (2019): Jurnal Elekto dan Mesin Terapan (ELEMENTER)
Publisher : Politeknik Caltex Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (469.653 KB) | DOI: 10.35143/elementer.v5i1.2496

Abstract

Perkembangan teknologi dalam bidang robotika tumbuh semakin pesat hingga tahun 2017. Di Indonesia sendiri pembuatan robot dengan tujuan ekplorasi terus dikembangkan demi mencapai tujuan penelitian. Terbatasnya bentuk dan fungsi robot-robot berkaki yang sudah dibuat untuk melakukan eksplorasi ruang, maka penulis mengeluarkan ide untuk membuat sebuah bentuk robot yang dapat bergerak lebih maksimal untuk melakukan eksplorasi. Oleh karena itu dibuatlah robot laba-laba berkaki delapan yang dapat berubah bentuk menjadi silinder atau dapat disebut robot transformer dimana prototype robot tersebut dilengkapi fitur kamera wireless yang dapat terkoneksi dengan telepon seluler dengan penyangga kamera yang dapat mempertahankan posisi vertical kamera tersebut. Robot tersebut dibuat dengan ukuran panjang x lebar x tinggi adalah 55cm x 40cm x 35cm. Robot tersebut dapat bergerak pada mode laba - laba dengan kecepatan maksimum ±3,51cm/s dan dapat menggelinding pada mode silinder dengan kecepatan maksimum ±12,8 cm/s. Saat melakukan proses transformasi dari laba-laba ke silinder, robot tersebut memerlukan waktu ±3,8s dan sebaliknya waktu yang diperlukan untuk transformasi dari silinder ke laba-laba ±11,6s.
Teknologi penguraian limbah jamur untuk peningkatan varian produksi petani jamur Desa Umbansari Dianita Wardani
Unri Conference Series: Community Engagement Vol 1 (2019): Seminar Nasional Pemberdayaan Masyarakat
Publisher : Lembaga Penelitian dan Pengabdian kepada Masyarakat Universitas Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31258/unricsce.1.108-112

Abstract

Oyster mushrooms are one type of mushroom that is cultivated commercially in Indonesia. Oyster mushroom is one type of mushroom that is commercially cultivated in Indonesia. Oyster mushrooms can be harvested within 1-3 months. So that from the business side of oyster mushrooms is very profitable. Namur because the business capital to buy mushroom seeds supplied from outside the area is reduced, then from 5 mushroom farmers who survive only 2 farmers. One of them is in the village of Umban Sari Atas, Rumbai District, Pekanbaru City. For this reason, a larger business capital is needed than before. This is where the idea arises to increase the variation in production from the mushroom. One of them is using baglog mushroom waste which has not been utilized into mushroom baglog briquettes. By using baglog waste technology, oyster mushrooms can be broken down and converted into mushroom baglog briquettes. The oyster mushroom baglog waste briquettes of course can be one of the alternative fuels that can be sold and made into a variant of production other than mushrooms. Thus it is expected to increase the income of mushroom farmers. In this PKM some of the problems faced are: (1) increased utilization of baglogjamur waste as a product variant of fungal development that has not been utilized or baglog waste in order to increase production and income. (2) Procurement of manual press machines to get the same baglog mushroom briquette density. The output of this PKM is the introduction of oyster baglog mushroom waste decomposition technology as the development of mushroom products and the manufacture of mushroom briquettes to oyster mushroom farmers in Upper Umban Sari village and the procurement of manual press machines for making baglog mushroom briquettes. In addition, from the PKM, there is an increase in the production of mushroom farmers, if previously the farmers can harvest 3-4 kg of mushrooms a day, now farmers can harvest mushrooms 5-6 kg per day. After using the combustion process using briquettes from processed baglog mushroom waste, farmers can also save costs for purchasing fuel (wood, rice husk) of Rp. 120,000 for the process of heating and steam mushroom seeds every month.
RANCANG BANGUN ALAT PENYEDIA PIRING PORTABLE Dianita Wardani; Tianur ,; Aditya Kosasih
AL-JAZARI JOURNAL SCIENTIFIC OF MECHANICAL ENGINEERING Volume 5, Nomor 1, Mei 2020
Publisher : Universitas Islam Kalimantan Muhammad Arsyad Al Banjari

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (246.836 KB) | DOI: 10.31602/al-jazari.v5i1.3040

Abstract

Perkembangan teknologi saat ini semakin pesat dengan perkembangan teknologi, terdapat banyak alat yang diciptakan untuk  membantu pekerjaan manusia bertujuan agar lebih efektif dan efisien. Penelitian ini membahas tentang Alat Penyedia Piring Portable yang dapat digunakan di restaurant, rumah makan. Alat ini bertujuan untuk menyediakan piring tambahan untuk diletakkan di rumah makan, agar pengunjung lebih mudah untuk mendapatkan piring tambahan apabila membutuhkan piring secara cepat untuk beberapa alasan seperti piring tambahan buat saus, nasi dan sambal. Selain itu digunakan  untuk meletakkan sisa makanan seperti tulang ikan. Penginputan pada alat ini dilakukan menggunakan keypad dengan sistem elektronika menggunakan Arduino Uno. Alat ini mengakomodir  pemesanan tambahan piring sebanyak 6 piring, piring yang dapat di simpan oleh alat sebanyak 12 piring. Setiap pemasukan piring tambahan penginputan melalui keypad. Proses penjepitan menggunakan metode mekanik, menggunakan motor linear yang terhubungkan dengan lift transport yang digerakkan menggunakan motor wiper. Alat ini mampu mengangkat piring dengan berat 9,6 kg dalam waku 2 menit 30 detik, sedangkan untuk piring dengan berat 3,2 kg alat ini membutuhkan waktu 1 menit 30 detik.  Keberhasilan alat penyedia piring portable untuk mencekam piring sebesar 90%.
Analisa Komposisi Material Barium M-Heksaferit (BAM) Berbahan Dasar Pasir Besi Pantai Cilacap dan Taluk Kuantan Dianita Wardani; Dewi Kurniasih; Aditya Maharani; Ratna Budiawati
Journal of Applied Electrical Engineering Vol 6 No 1 (2022): JAEE, June 2022
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/jaee.v6i1.4047

Abstract

Analyzing the material composition of iron sand from Cilacap beach and iron sand from Taluk Kuantan beach in Riau. In this research, the synthesis of barium M-Hexaferrite is made from iron sand from Cilacap beach and iron sand from Taluk Kuantan beach, Riau. In the research method, the test was carried out using composition analysis with FTIR test. The characteristics of the test using the FTIR test that the iron sand of the Cilacap beach has an Fe content of 86.53% and does not carry out refining. while the iron sand of Taluk Kuantan beach has an Fe content of 82.86% and is not purified. Based on the wave number value, BAM doped with Cu has the best wave number value and the highest transmittance value is around 92% at wavelengths from 1467.03 to 669.56 cm−1.
Analisis Kegagalan Material Aluminium 5052 sebagai Aplikasi Bahan Lambung Kapal Terhadap Pengaruh Salinitas Air Laut Imah Luluk Kusminah; Dianita Wardani; Lely Pramesty; Richo Oktavian Indarto
G-Tech: Jurnal Teknologi Terapan Vol 7 No 1 (2023): G-Tech, Vol. 7 No. 1 Januari 2023
Publisher : Universitas Islam Raden Rahmat, Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (230.1 KB) | DOI: 10.33379/gtech.v7i1.1853

Abstract

As an archipelagic country, ship transportation is very important to connect between islands in Indonesia. In ship construction planning, ship hull material is an important factor because corrosion often occurs. Corrosion is the deterioration of a material due to a chemical reaction. This research is an interesting scientific discussion to find out cause the failure of ship hull materials. This research was conducted using an experimental method. Quantitatively the weight loss of aluminum material is calculated according to ASTM G31-72, then calculates the corrosion rate and analyzes the factors that affect the corrosion rate with XRD testing. From the results of the weight loss test, the largest corrosion rate occurred in the material located at 3.6% NaCl salinity conditions of 12.18 mpy with an immersion time of 1 month. From the results of XRD analysis showed that there were compounds 2NaAlO2 and Al2O3 at the highest peak intensity.
Synthesis of Materials Al(OH)3 Based on Sand in Batam Island as a Geopolymer for Brick Materials Ulfa Nabilla; Dianita Wardani; Amnur Akhyan; Roni Novison
International ABEC 2021: Proceeding International Applied Business and Engineering Conference 2021
Publisher : International ABEC

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1126.346 KB)

Abstract

Bauxite sand is beach sand on the island of Batam which contains a lot of kaolin, this is the result of the FTIR test that has been tested. Kaolin has a good composition of alumina (Al₂O₃) and silica (SiO₂) compounds to produce geopolymer materials for quality building materials. The geopolymer material synthesis process uses materials, namely Batam island bauxite sand, fly ash from burning sugarcane waste, and redmud and then mixed with wet materials such as NaOH and Sodium silica which are varied as much as 7% and 5%. After the geopolymer material, XRD testing was carried out to determine the angle 2 on the geopolymer and continued with the process of making bricks with a mixture of geopolymer and clay materials and then molding them with brick molds manually. The bricks were given curing or heating treatment for 24 hours with temperature variations of 80°C and 90°C then aging or left in the open for 14 days, then the bricks will be tested by testing hardness, compressive strength and impact testing at the Mechanical Engineering workshop Caltex Riau Polytechnic. The results of the tests that have been carried out are found that the compressive strength of the geopolymer brick composition 1 at 90°C is the brick that has the highest compressive strength value of 12.84 kg/cm². Impact testing is to see the toughness value of a material increases the impact value, the object is getting more, in this test geopolymer brick composition 1 + 90°C and geopolymer brick Composition 2 + 80°C are materials that are not or easily brittle with an impact price of 0.0063 J/mm² and 0.0071 J/mm². In the Brinell hardness test, the highest value was found by geopolymer bricks with a composition of 1 + 90°C, after three experiments the average HB value was 83.21. is the highest HB value of other composition geopolymer bricks and ordinary bricks.
Analisa Fleksibilitas Sistem Perpipaan Pada Suction Dan Discharge Air Gan Compressor Pekik Mahardhika; Dianita Wardani; Hafizh Akbar Alam
JURNAL INTEGRASI Vol 15 No 1 (2023): Jurnal Integrasi - April 2023
Publisher : Pusat Penelitian dan Pengabdian Masyarakat Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/ji.v15i1.4553

Abstract

Pada penelitian ini dilakukan analisa fleksibilitas pada jalur masuk dan keluar sistem perpipaan kompresor. Fluida pada jalur sistem perpipaan kompresor adalah udara. Udara merupakan fluida yang bersifat dinamis dan kompresibel. Jalur sistem perpipaan ini merupakan jalur pipa yang terhubung dengan mesin rotasi (kompresor). Jalur perpipaan yang terhubung dengan mesin rotasi termasuk kriteria perpipaan kritis. Analisa ini untuk memastikan bahwa jalur sistem perpipaan air gan compressor dalam keadaan aman. Analisa fleksbilitas pada makalah ini membahas tentang gaya pada pipa, gaya pada penopang pipa, pergerakan & rotasi pada jalur pipa, dan translasi & rotasi akibat terjadinya getaran dari kompresor. Alat bantu yang digunakan pada penelitian ini adalah Bentley Autopipe v8i. Berdasarkan hasil dan kesimpulan bahwa pipa jalur suction dan discharge saat mengalami beban statis memiliki gaya pipa maksimum terbesar pada sumbu -Fx point N09 sebesar 20745 kg, gaya penopang pipa terbesar pada sumbu Fx point D15 sebesar 20737 kg, pergerakan pipa terbesar pada sumbu -Dy point B27 sebesar 22,47 mm, dan rotasi pipa terbesar pada sumbu -Rx point B27 sebesar 0,38 deg. Ketika pipa terjadi beban dinamis mengalami translasi terbesar pada sumbu -Tx point H10 sebesar 4,7422 mm dan rotasi terbesar pada sumbu -Rx point H09 sebesar 5,9234 deg. Kesimpulan pada penelitian ini adalah menurut code ASME B31.3 bahwa sistem perpipaan air gan compressor dinyatakan aman.
SOSIALISASI PENANGGULANGAN KEBAKARAN DI SMK NASIONAL DAWARBLANDONG MOJOKERTO Imah Luluk; Dianita Wardani; Egyt Yusuf Hidayat; Dewi Rizqi Maimunah; Alma Lia Hakim
Jurnal Cakrawala Maritim Vol 2 No 2 (2019): Jurnal Cakrawala Maritim
Publisher : Pusat Penelitian dan Pengabdian Masyarakat (P3M) - PPNS

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35991/cakrawalamaritim.v2i2.2893

Abstract

Kesadaran akan pentingnya Keselamatan dan Kesehatan Kerja (K3) merupakan hal yang sangat krusial dalam lingkungan kerja atau di tempat-tempat umum. Salah satu aspek penting dalam K3 adalah penanganan kebakaran. Kebakaran dapat terjadi di mana saja dan kapan saja, sehingga pemahaman tentang cara memadamkan api dengan benar menjadi sangat penting bagi setiap individu, terutama bagi kalangan pelajar. Dalam upaya meningkatkan kesadaran tentang pentingnya kebakaran dan kesiapsiagaan menghadapinya, Mahasiswa Teknik K3 dan Dosen dari Politeknik Perkapalan Negeri Surabaya (PPNS) telah mengambil inisiatif untuk melakukan sosialisasi di SMK Nasional Dawarblandong, Mojokerto. SMK Nasional Dawar Blandong merupakan salah satu sekolah menengah yang fokus pada jurusan otomotif, kimia industri, akuntansi, jaringan komputer dan sebagainya. Berdasarkan hal tersebut penting untuk siswa SMK dapat meningkatkan kesadaran dan pengetahuan tentang pentingnya keselamatan dan kesiapsiagaan dalam menghadapi kebakaran.