Article Per Year (5 Year)
p-Index From 2020 - 2025
0.61
P-Index
This Author published in this journals
All Journal Warta Ardhia : Jurnal Perhubungan Udara Jurnal Polimesin
Nuranto, Awang Rahmadi
Unknown Affiliation
Automotive Engineering Control & Systems Engineering Engineering Materials Science & Nanotechnology Mechanical Engineering Transportation

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

 1 
Optimization of Double Hole Composite Plate on the Floater Compartment of Amphibious Aircraft Using Taguchi Method Nurrohmad, Abian; Antares, Quincy; Nuranto, Awang Rahmadi; Nugroho, Afid
WARTA ARDHIA Vol 49, No 2 (2023)
Publisher : Badan Kebijakan Transportasi, Kementerian Perhubungan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25104/wa.v49i2.520.87-95

Abstract

A floater or pontoon is one of the most important components of amphibious aircraft to assist the take-off and landing operation. The inner structure of the floater consists of compartments to carry some payload and to reinforce the structural strength due to water and aerodynamic load that occurred during the aircraft operation. The composite material is chosen instead of metal to reduce the weight of the floater. One of the problems on the composite panel is the existence of some holes due to joint with another part or also to minimize its weight. In this study, the optimization of the composite plate with the existence of a double hole is done using the Taguchi Method. The objective of this optimization is to minimize the stress that happens due to the tensile load. The Finite Element Method is used to calculate the maximum stress and stress distribution on the plate. Tsai-Hill failure criterion is used to make sure that the optimum design does not fail. This optimization considers open hole configuration, the ratio between diameter, and hole distance, as well as the fiber orientation as the control factors. The Taguchi L9 Orthogonal Array is used to make 9 design variations from 3 control factors and 3 levels. This process also considers the thickness of the lamina and material strength as noise factors. The optimization process results in the optimum composite design as follows: 1st double hole configuration (in line with the load direction), the ratio between diameter and hole distance is 0.5, and the fiber direction is [0/90/45/-45]s. The maximum in-plane stress of the optimum design is 39.56 MPa with the Tsai-Hill value is 0.23, so the design does not fail. This optimum configuration of the composite plate can be used to make design considerations for an amphibious aircraft floater compartment.
Optimization of Double Hole Composite Plate on the Floater Compartment of Amphibious Aircraft Using Taguchi Method Nurrohmad, Abian; Antares, Quincy; Nuranto, Awang Rahmadi; Nugroho, Afid
WARTA ARDHIA Vol. 49 No. 2 (2023)
Publisher : Sekretariat Badan Kebijakan Transportasi, Kementerian Perhubungan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25104/wa.v49i2.520.87-95

Abstract

A floater or pontoon is one of the most important components of amphibious aircraft to assist the take-off and landing operation. The inner structure of the floater consists of compartments to carry some payload and to reinforce the structural strength due to water and aerodynamic load that occurred during the aircraft operation. The composite material is chosen instead of metal to reduce the weight of the floater. One of the problems on the composite panel is the existence of some holes due to joint with another part or also to minimize its weight. In this study, the optimization of the composite plate with the existence of a double hole is done using the Taguchi Method. The objective of this optimization is to minimize the stress that happens due to the tensile load. The Finite Element Method is used to calculate the maximum stress and stress distribution on the plate. Tsai-Hill failure criterion is used to make sure that the optimum design does not fail. This optimization considers open hole configuration, the ratio between diameter, and hole distance, as well as the fiber orientation as the control factors. The Taguchi L9 Orthogonal Array is used to make 9 design variations from 3 control factors and 3 levels. This process also considers the thickness of the lamina and material strength as noise factors. The optimization process results in the optimum composite design as follows: 1st double hole configuration (in line with the load direction), the ratio between diameter and hole distance is 0.5, and the fiber direction is [0/90/45/-45]s. The maximum in-plane stress of the optimum design is 39.56 MPa with the Tsai-Hill value is 0.23, so the design does not fail. This optimum configuration of the composite plate can be used to make design considerations for an amphibious aircraft floater compartment.
Shear strength comparison of single lap and joggle lap adhesive joints in carbon fiber composites manufactured via vacuum-assisted resin infusion Pratama, Mikhael Gilang Pribadi Putra; Abdurohman, Kosim; Pratomo, Rezky Agung; Hidayat, Ryan; Ramadhan, Redha Akbar; Aritonang, Rian Suari; Nurtiasto, Taufiq Satrio; Ardiansyah, Riki; Nugroho, Afid; Nuranto, Awang Rahmadi; Wandono, Fajar Ari; Targani, Dudi; Ula, Nur Mufidatul
Jurnal Polimesin Vol 22, No 5 (2024): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v22i5.5437

Abstract

The extensive utilization of composite materials has spurred the advancement of diverse joining techniques suitable for components constructed from such materials. This study focuses on the examination of two specific types of joints: single lap and joggle lap joints. The specimens utilized were composed of unidirectional carbon fiber composite combined with vinyl ester resin, manufactured via the vacuum-assisted resin infusion method. Vinyl ester adhesives were employed in the bonding process, with the joint surfaces undergoing sanding treatment prior to testing. Mechanical testing was conducted on the specimens according to ASTM D5868 standard, employing a constant crosshead speed until failure occurred. The test results reveal that the shear strength of single lap joints surpasses that of joggle lap joints. Within the single lap joint configuration, a mixed failure mode comprising both adhesive and cohesive failure is observed. Conversely, in joggle lap joints, substrate delamination is prevalent, suggesting the predominance of peel stress during loading.
Co-Authors Abdurohman, Kosim Antares, Quincy Aritonang, Rian Suari Nugroho, Afid Nurrohmad, Abian Nurtiasto, Taufiq Satrio Pratama, Mikhael Gilang Pribadi Putra Pratomo, Rezky Agung Ramadhan, Redha Akbar Riki Ardiansyah, Riki Ryan Hidayat, Ryan Targani, Dudi Ula, Nur Mufidatul Wandono, Fajar Ari