cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
Rendihernawan
Contact Email
jmem.secretariat@president.ac.id
Phone
-
Journal Mail Official
jmem.secretariat@president.ac.id
Editorial Address
-
Location
Kota bekasi,
Jawa barat
INDONESIA
Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mechatronics)
Published by President University
ISSN : 25276212     EISSN : 25412876     DOI : -
Core Subject : Science, Engineering,
Energy Materials Science & Nanotechnology Mechanical Engineering Transportation
Journal of Mechanical Engineering and Mechatronics merupakan jurnal keilmuan bidang teknik mesin dan mechatronics yang memuat tulisan-tulisan ilmiah mengenai penelitian-penelitian murni dan terapan serta ulasan-ulasan umum tentang perkembangan teori, metode dan ilmu-ilmu terapan terkait.
Arjuna Subject : -
Articles 6 Documents
 1 
Search results for , issue "Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS" : 6 Documents clear
PERANCANGAN SISTEM DISTRIBUSI ZONA II TANJUNG BALAI KARIMUN KEPULAUAN RIAU Ivan Cahya Raswoko; Syamsir Abduh; Maula Sukmawidjaja
Journal of Mechanical Engineering and Mechatronics Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (338.15 KB) | DOI: 10.33021/jmem.v4i1.661

Abstract

The distribution system is one of the most important elements to be able to distribute electrical energy from power plants to consumers. Tanjung Balai Karimun, Kepulauan Riau is an island near the island of Batam. PT Karimun Power Plant has built a plant with a total capacity of 7.5 MW consisting of 5 machines with a capacity of 1.5 MW each. This research is aimed at the appropriate distribution system to be applied there. Medium voltage air duct is one of the existing systems, and is suitable to be applied in Zone II Tanjung Balai Karimun Riau Islands. The cross section size used in the calculated conduit is 100 mm² in the upstream and 16 mm² in the downstream. These conveyors are supported by a pole with a height of 12 m and with a distance between the poles as wide as 100 m. in this system there is also a transformer with a capacity of 160-4000 kVA. This system was tested using ETAP software and produced data that the available generator was not enough to carry the burden in Zone II Tanjung Balai Karimun. Due to inadequate power generation, the long-term solution is to increase the number of plants while the short-term solution is to reduce the burden to be carried.Keywords. SUTM, Sistem Distribusi, ETAP
SIMULASI AUTOMATIC TRANSFER SWITCH DAN AUTOMATIC MAINS FAILURE DENGAN PLC OMRON SYSMAC CP1E Suhanto Suhanto
Journal of Mechanical Engineering and Mechatronics Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (487.142 KB) | DOI: 10.33021/jmem.v4i1.662

Abstract

Electric power supply is the main requirement of equipment at the airport, therefore the reliability of the supply of power supplies is a top priority to support flight services. In addition to PLN as the main power supply the generator is used to supply a backup power supply. Automatic Transfer Switch (ATS) and Automatic Mains Failure (AMF) control systems are needed to regulate the switching of power supplies from PLN to Genset or vice versa. The ATS and AMF control systems use the Omron Sysmac CP1E PLC with a display using Easy Builder 8000 from Weintek which functions as an ATS and AMF monitor and control. Test results on ATS and AMF in manual and automatic modes, the system runs well.Keywords. Automatic Transfer Switch (ATS), Automatic Mains Failure (AMF), PLC
PENGARUH MEDIA PENDINGIN PADA PROSES HARDENING TERHADAP KETANGGUHAN BAJA S45C Govar Arianzas; Dody Prayitno
Journal of Mechanical Engineering and Mechatronics Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (485.111 KB) | DOI: 10.33021/jmem.v4i1.655

Abstract

The purpose of this study was to determine the effect of vegetable oil or water cooling media on the Hardening process on the value of the impact strength of S45C. The research method of the S45C steel sample was heated at 900˚C for 1 hour. The sample then in quenching the medium of water or vegetable oil is then tested for impact using the Charpy method. Research result. The value of impact strength of S45C steel is 0.416 Joule / mm2, Hardening (900˚C, 1 Hour) with Quenching Air media causing the value of impact strength to decrease from 0.416 Joule / mm2 to 0.135 Joule / mm2, Hardening (900˚C, 1 Hour) with media of Vegetable Oil Quenching causes the strength value to increase from 0.416 Joule / mm2 to 2,276 Joule / mm2, Microstructure in S45C steel "Raw Material" is ferrite and pearlite, Microstructure sample code "Quenching Air" is Martensite and Troostite, Microstructure sample code "Quenching MinyakSayur "is Bainit.Keywords. Impact Strength, Hardening, Water, Vegetable Oil.
FINITE ELEMENT ANALYSIS WITH STATIC AND DYNAMIC CONDITIONS OF SPARE WHEEL CARRIER FOR OH 1526 FABRICATED BY SAPH 440 HOT ROLLED STEEL Norbertus Krisna Aditya Utomo; Lydia Anggraini
Journal of Mechanical Engineering and Mechatronics Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (469.34 KB) | DOI: 10.33021/jmem.v4i1.663

Abstract

Spare Wheel Carrier is a component that must exists in a heavy duty vehicle. The function of this part is to store additional wheel in order to deal with punctures that might happen to the tire. This part is usually placed in the middle of the vehicle in order to maintain the position of center of gravity of the vehicle. The purpose of this research is to analyze the strength of SAPH 440 as the manufacturing material of the Spare Wheel Carrier from one automotive company. The Spare Wheel Carrier will endure a load of a replacement tire for its entire cyclic load. The load itself will generate stresses and strains in the part, especially in the welding joint. Therefore, the analysis is to be done to provide the automotive company with the result to determine improvement that should be made. The method that is used in this research is using CATIA software to create the three dimensional model of the part. Later, we import the model to ANSYS software to analyze the equivalent stress, equivalent elastic strain, directional deformation, and cyclic load for steady load, live load, and shock load. The calculation shows that the part can endure the force from steady load, with the estimated cyclic load of 70,723 cycles. But for live load, the stress and strain will be happening around the yield strength and offset yield strength and the estimated cyclic load declining significantly to 6,358.6 cycles. Furthermore, the shock load result stated that the stress and the strain are exceeding the yield strength and reduces the estimated cyclic load to 1,843.9 cycles. In conclusion, the material is proven to be safe for usage as the Spare Wheel Carrier manufacturing material.Keywords. spare wheel carrier, SAPH 440, stress, strain, deformation, cyclic load
STUDI POTENSI PEMBANGKIT LISTRIK TENAGA GELOMBANG LAUT DENGAN METODA OSCILATING WATER COLUMN DI PERAIRAN KENDARI INDONESIA Faulincia Faulincia
Journal of Mechanical Engineering and Mechatronics Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (449.556 KB) | DOI: 10.33021/jmem.v4i1.656

Abstract

Referring to Law Number 30 of 2007 concerning Energy, the development of techniques the conversion of electrical energy by using alternative energy sources is interesting for followed for the past few years. This paper discusses calculation analysis power potential of ocean wave conversion using the Oscilating Water system Column (OWC) in the marine area of Indonesia. This system was chosen because it has many advantages compared to other systems and in accordance with the marine and coastal areas of Indonesia. From the calculation of power, the smallest power that can be produced is equal to 348.5838 Watts while the biggest power that can be produced is 623291.4 Watts The application of the oscillating water column system in Kendari waters with an efficiency of 11.971%.Keywords. oscillating water column (OWC), ocean wave energy, electrical energy, power potential,wavelength
MENURUNKAN KERUSAKAN YANG TIDAK TERJADWAL (UNSCHEDULE BREAKDOWN) SISTEM BAHAN BAKAR PADA UNIT KOMATSU HD 1500-7 DIPT UT SITE KALIMANTAN TIMUR Vuko A.T. Manurung; Yohanes Trijoko; Randy Putra Afani
Journal of Mechanical Engineering and Mechatronics Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (415.897 KB) | DOI: 10.33021/jmem.v4i1.660

Abstract

This study discusses the modification of the fuel system in the Komatsu HD 1500-7 unit, which aims to improve PA (physical avaibility) and make unit downtime faster. The basis of this research was carried out because of the frequent replacement of fuel filters due to clogged fuel flow so that the cost of repairs and the consequences of not operating the unit became high. This repair process uses the main components in the form of Arduino Mega 2560 program, LED lights, LCD monitors and sensors. The working principle of this improvement is that the tool works together to forward the voltage signal from the sensor to Arduino, then the signal will be converted into writing data on the LCD. The LED light functions as a warning lamp and the speaker in the cabin functions as a warning sound. The result of making this modification system is that it can be determined the right time to replace the fuel filter before a deadlock occurs and cause the unit to die suddenly.Keywords. fuel system, Physical Avaibility, Downtime

Page 1 of 1 | Total Record : 6

 1 

Filter by Year

2019 2019


Reset
Filter By Issues
All Issue Vol 10, No 1 (2025): Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mech Vol 9, No 2 (2024): Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mecha Vol 8, No 2 (2023): Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mecha Vol 8, No 1 (2023): Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mecha Vol 7, No 2 (2022): Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mecha Vol 7, No 1 (2022): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 6, No 2 (2021): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 6, No 1 (2021): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 5, No 2 (2020): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 5, No 1 (2020): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 4, No 2 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 4, No 1 (2019): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 3, No 2 (2018): Journal of Mechanical Engineering and Mechatronics Vol 3, No 1 (2018): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS Vol 2, No 02 (2017): Journal of Mechanical Engineering and Mechatronics Vol 2, No 01 (2017): Journal of Mechanical Engineering and Mechatronics Vol 1, No 02 (2016): Journal of Mechanical Engineering and Mechatronics Vol 1, No 02 (2016): Journal of Mechanical Engineering and Mechatronics Vol 1, No 01 (2016): Journal of Mechanical Engineering and Mechatronics More Issue