cover
Contact Name
Mohammad Shihab
Contact Email
shihab@president.ac.id
Phone
-
Journal Mail Official
-
Editorial Address
Jalan Ki Hajar Dewantara Jababeka, Cikarang Baru, Bekasi 17550
Location
Kota bekasi,
Jawa barat
INDONESIA
Journal of Industrial Engineering
  • journalofIndustrialEngineerin
  • Website
Published by President University
ISSN : 25033670     EISSN : 25274139     DOI : -
Core Subject : Engineering,
JIE: Journal of Industrial Engineering (Online ISSN: 2527-4139; Printed ISSN 2503-3670) is a scientific journal in the field of industrial engineering that publishes scientific writings on pure and applied research in industrial system, including (but not limited to): Production system, Inventory management, Quality control & management, Work system analysis, Product design, Optimation, and Productivity.
Articles 6 Documents
Search results for , issue "Vol 3, No 2 (2018)" : 6 Documents clear
Analisis Penambahan Kapasitas Udara Bertekanan untuk Pneumatik pada Mesin Kertas 01 di Perusahaan Kertas, Bekasi Jazid Rizkon; Anastasia Lidya Maukar; Ineu Widaningsig Sosodoro
JIE Scientific Journal on Research and Application of Industrial System Vol 3, No 2 (2018)
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (557.707 KB) | DOI: 10.33021/jie.v3i2.524

Abstract

In paper mills, paper presses, paper rolling, and automatic valves are very important machines for the continuity of the production process. But at present, problems often occur, namely the machines cannot work optimally, because the need for compressed air for pneumatic tools is not enough fulfilled. To ensure this, the capacity calculation of the pressurized air compressor and the need for pressurized pneumatic tools are carried out. The results of the calculation show that the pressurized air requirements of pneumatic tools are greater than those produced by the kompresor with a difference of 2,972 litres/minute. To get the best decision, an Equivalent Uniform Annual Cost (EUAC) analysis is performed to determine the economic life of the compressor machines currently in use. In addition, an inspection of compressor damage data was also carried out. The results of the analysis show that the replacement of the compressor does not need to be done because the current engine life is under the economic age. Thus, the decision taken is to purchase a new compressor with a capacity of 28,000 litres/minute. The calculation using the present worth cost (PWC) analysis obtained the smallest total cost with consideration of the additional energy costs is Atlas Copco GA160 Compressor worth Rp 55,094,911,134. Without considering additional energy costs, the results of the calculation of the smallest total PWC is the choice of Kaeser DSD250 amounting to Rp. 8,044,785,017. Then after sensitivity analysis with consideration of interest rates and electricity costs, Atlas Copco GA160 has the lowest total cost. Thus, the changes in interest rates and an increase of electricity costs are not sensitive enough to the selection of machines for investment.
Rancang Bangun Prototipe Mesin Gravir Laser Berbasis Mikro-kontroler Arduino Nanang Ali Sutisna; Harist Fauzi
JIE Scientific Journal on Research and Application of Industrial System Vol 3, No 2 (2018)
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (419.463 KB) | DOI: 10.33021/jie.v3i2.525

Abstract

Nowaday, the use and demand of laser engraving machines is increasing for production and practical activities in vocational schools and engineering faculty in Indonesia. However, the price of laser engraving machine in the market is still quite high. Therefore, there is a need to find a solution to overcome this problem by designing a laser-engraving machine that is devoted for practical purposes at affordable prices. The control system on the laser-engraving machine is designed using an Arduino Nano-based 2-axis CNC controller, with three stepper motor drive actuators, to drive the machine on the x, y, z axis and laser axis with 2500 mW of power. To prevent damage if there is a movement error, the machine is equipped with emergency stop button. The use of a control system with an Arduino nano-based 2-axis CNC microcontroller is selected on the laser engraving machine because it is open source and more affordable. It is expected that by implementing Arduino nano ATmega328 microcontroller as a prototype, in the future the control system can be developed further so that the control system is more stable. From the results of laser engraving machine testing using laser distance parameters, laser power and laser speed motion, obtained the value of the best engraving machine parameters to be used as standard parameters.
Penerapan Metode PDCA untuk Menurunkan Tingkat Kerusakan Mesin pada Proses Produksi Penyalutan Cepi Kurniawan; Hery Hamdi Azwir
JIE Scientific Journal on Research and Application of Industrial System Vol 3, No 2 (2018)
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (419.463 KB) | DOI: 10.33021/jie.v3i2.526

Abstract

The coating process is the process of covering the tablet with a thin layer of substance which generally has very little effect. The process coating process uses a Driam machine and the machine has a very high utilization of 125%. The company's ability to provide additional salute machines requires time in its investment, remedial efforts to reduce the damage level of the salute machine are needed so as not to increase machine utilization, while the damages that occured in the coating process from January to December 2016 are Speed Pump, Air Flow Damper, Spray Gun, Supply Compressed Air, Steam, Pan Speed, & Wind Hose. From the background of the problem the company needed repairs that were useful to reduce the level of damage to the salute machine. These improvements are carried out using the Plan Do Check Action (PDCA) method. The PDCA method is a repetitive process improvement activity to solve a problem in quality control and is included in the Total Quality Management (TQM) in which TQM is the application of quantitative methods and human knowledge to improve materials and services which of course improves processes and efforts to meet customer satisfaction . The level of damage to the machine salute has decreased after repairs to the engine damage Pump Speed & Air Flow Damper where it eliminates 2 of 7 damage that occurs in the coating process or by 45.6% of the total damage.
Menurunkan Problem Reject Pinhole di Proses dengan Konsep DMAIC di PT. XYZ, Purwakarta Hikmat Mulyana M; Andira Andira; Nurhayati Surbakti
JIE Scientific Journal on Research and Application of Industrial System Vol 3, No 2 (2018)
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (572.425 KB) | DOI: 10.33021/jie.v3i2.527

Abstract

PT XYZ is one of the flexible manufacturing industries. In terms of overcoming competition in the printing industry, PT XYZ built the Rotogravure company in 2011. The subsidiary is engaged in manufacturing Cylinder Rotogravure which supplies PT XYZ units. From a few years back since the establishment of this company, the target that should have been reached in amount of 5760 Cylinder / year. This target hasnot been achieved. This occurs because there is a problem in the production process reaching ± 49.4% and continues to appear which results in a disrupted delivery schedule, many customer complaints due to the low quality goods being shipped.The method used for this improvement process is the system or concept of Six Sigma namely DMAIC. From the DMAIC method, the tools used for the analysis process are the Pareto, Fishbone, 5W1H and Data Sheet diagrams. These tools are core tools that are focused on finding problems that often occur at PT XYZ. From the results of this improvement, a design is got to make the cleaning process aids, there were changes in parameters in the production process by reducing the current density and temperature in the Copper machine with a temperature of 30OC and current density of 20 A / dm2. The research and improvements that have been made are 94.45% with a total pinhole wastage of 1 cylinder unit.
Rearranging Dispatching Layout to Minimize Dispatching Time A. Saptari; A. Azlan; E. Mohamad
JIE Scientific Journal on Research and Application of Industrial System Vol 3, No 2 (2018)
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (557.707 KB) | DOI: 10.33021/jie.v3i2.523

Abstract

Reorganizing a layout entails a massive adjustment and thorough planning is essential before a new layout implemented. This project is to reorganize layout at dispatching area of a manufacturing industry which produces apparel accessories products. Current arrangement at the dispatching area of the company shows an interrupted flow path of activities and scattered of queuing cartons at area of activities in the dispatching line which brought to operating issues. The project aims to identify problem in current arrangement of dispatching layout, analyze the the problem and propose an alternative layout that reduces dispatching time. Time studies were applied to collect data on current performance, developing alternative arrangement, and evaluation the alternative through Witness simulation. The finding showed total dispatching time of current layout consumes 30.77 minutes to complete one dispatching job with distance travel of 162.83 meters. Better alternative layout is developed by the approach of facility planning process. Results showed the dispatching time has reduced by 32.79%, which the alternative layout only consumes 20.68 minutes to complete one dispatching job with shorter distance travel of 109.44 meters.
Usulan Pengurangan Jumlah Cacat Part Produk Frame X Muhammad Musafak; Johan K. Runtuk; Sumartono Sumartono
JIE Scientific Journal on Research and Application of Industrial System Vol 3, No 2 (2018)
Publisher : President University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (257.951 KB) | DOI: 10.33021/jie.v3i2.528

Abstract

Quality has an important role in a company. A defect product can The customer complaint of PT XYZ keep increasing in November 2017 in amount of 13.178 pcs. The highest defect occurred on frame X and visual problem. After analyzing using fishbone diagram, the cause of highest defect is caused by method and material.

Page 1 of 1 | Total Record : 6