cover
Contact Name
Oktaf Brillian Kharisma
Contact Email
ijeere@irpi.or.id
Phone
+6281331880991
Journal Mail Official
ijeere@irpi.or.id
Editorial Address
Jl. Tuah Karya Ujung C7, Kel. Tuah Madani, Kec. Tampan Kota Pekanbaru - Riau, Indonesia
Location
Kota pekanbaru,
Riau
INDONESIA
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE)
ISSN : 27971155     EISSN : 27970868     DOI : https://doi.org/10.57152/ijeere.v2i1
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) is a scientific journal published by the Institute Research and Publication Indonesia (IRPI) in collaboration with several universities throughout Riau and Indonesia. IJEERE will be published 2 (two) times a year, June and December, each edition contains 15 (fifteen) articles. Articles can be written in Indonesian or English. articles are original research results with a maximum plagiarism of 20%. Articles submitted to IJEERE will be reviewed by at least 2 (two) reviewers. Articles submitted must meet the assessment criteria and comply with the instructions and templates provided by IJEERE. Authors must upload the Intellectual / Copyright Statement when submitting the manuscript. Papers must be submitted via the Open Journal System (OJS) in .doc or .docx format. The entire process until IJEERE is issued is free of charge. IJEERE is registered in National Library with Number International Standard Serial Number (ISSN) Printed: 2797-1155 and Online 2797 - 0868. The focus and scope of IJEERE includes: (a) Wireless Communication, (b) Optical Communication, (c) RF, Microwave, and Antenna Design, (d) • Telecommunication Networks, (e) Control Systems, (f) Nuclear New Energy, (g) Renewable Energy
Articles 64 Documents
An Economic and Smart Greenhouse System using Microcontroller for Sustainable Agriculture: A Case Study Bhandari, Samir Raj
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.477

Abstract

The demand of food is continuously increasing as compared to its production due to the rapid urbanization, population growth and climate change. In this scenario, greenhouse is an alternative to maximize the food production without increasing fertile land. The smart greenhouse uses integrated sensor system to control and monitor the environment inside the greenhouse. This research focuses on designing cost effective and automatic parameter monitoring system for existing greenhouses using microcontroller. The research was carried out in two parts, initially, feedbacks regarding the current greenhouse and scopes for automation were collected through field survey with the farmers and later, an experimental model was developed in accordance with the data collection. From the data analysis of field survey, it was found that current greenhouses had problems in effective temperature and irrigation control. Thus, the designed model carries out automatic cooling and irrigation with effective monitoring of this parameter in a display. Furthermore, upon economic analysis, labor cost for monitoring of greenhouse was Rs. 1, 66,860per annum which will be reduced. Meanwhile, discounted payback period analysis showed that initial investment will recover after 2.34 years with the cost for conversion to smart greenhouse at Rs 552 sq. meters.
Studi Komprehensif Pembangkit Mikro Hidro dan Potensinya: Studi Kasus: A Comprehensive Study of Micro Hydro Plant and its Potential: A Case Study Bhandari, Samir Raj
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.478

Abstract

The existing national grid network is unreliable in providing power to the rural hilly areas due to difficult to geographical structure of Nepal. Therefore, the demand ofMicro-hydro power plants are increasing in these areas of Nepal. MHPs produces up to 100kW and helps to distribute power to isolated communities. The main objective of this research is to study the technical and economic feasibility of micro hydropower in Gairibari Jharna, Kalika Municipality-08, Chitwan, Nepal.This project is an explanatory type research which is based on the primary data collected through questionnaires and field survey. Furthermore, upon the analysis of data collected from 41 out of 87 households, it showed positive interpretations.Through the qualitative and quantitative research, average power demand for each household was found to be 513.29 W leading to an average energy demand of 1.9 kWhr per day. Meanwhile, technical calculations showed the head available to be98m, discharge produced to be 0.24221m3/s and the ultimate design reflected the generated power to be 12 KW. Through the detail analysis of cost, budget for this projectwas NepaleseNRs 36,84,730 ($ 28,102.7) . After economic analysis of cost the payback period is calculated to be 15.37 years.
Rancang Bangun Sistem Monitoring Karakteristik Solar Cell dan Peltier Berbasis Internet Of Thing: Design and Development Of Solar Cell and Peltier Characteristics System Base On Internet Of Thing Murnis, Eko putra; bandria, sepannur
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.481

Abstract

This IOT-based monitoring tool for the characteristics of solar cells and Peltier is a tool that is used as a comparison for solar cells and Peltier. with this tool, experiments can be carried out to determine the characteristics of solar cells and peltiers, with direct observation methods to collect data on sources of electrical energy that can be produced by solar cells and peltiers, Therefore, 3 experiments were carried out using a 2W/6V solar cell, Peltier TEG SP1848 and 3W/12V LEDs. The first was data collection of the electrical energy source produced by 2 solar cells, connected in series with an experimental length of 60 minutes and producing a voltage of 10, 39 V, 0.11 A current and 1.10 W power, the second experiment of data collection on a solar cell and Peltier series circuit with an experimental time of 60 minutes produces a voltage of 10.38 V, a current of 0.13 A and a power of 1.30 W In the third experiment, data collection on a series of solar cells and a parallel circuit on a Peltier with an experimental length of 60 minutes resulted in a voltage of 11.13 V, a current of 0.10 A and a power of 1.10 W. produces a voltage of 0.75 V better than a series circuit with a greater resistance and produces a voltage of 0.74 V better than a series circuit of 2 voltage solar cells with a temperature of each peltier 37? to 39 ? , with The level of decline is still stable when the solar cell is not exposed to sunlight and the lack of heat energy sources that can be absorbed by the Peltier, it can be said that peltier can help the effectiveness of solar cells. Keywords : PZEM-017 sensor DC, ESP8266, Blynk IOT
Analisis Aspek Teknis dan Ekonomis Pemanfaatan Sampah Plastik Polyprophylene Sebagai Alternatif Bahan Bakar : Analysis of Technical and Economic Aspects Utilization of Polyprophylene Plastic Waste as an Alternative Fuel Ar Rasyid, Fadhil
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.482

Abstract

Pekanbaru is the largest city in Riau Province. Pekanbaru has 3 zones of waste transportation, which are combined at the Muara Fajar final disposal site (TPA). The waste at the Muara Fajar TPA consists of organic and inorganic waste, 35% of which is inorganic waste is polyprohylene type plastic waste. The purpose of this study was to analyze the technical aspects and economic aspects of the use of plastic waste as an alternative fuel using the pyrolysis method using the SuperPro Designer software. The results of the research on the technical aspects of the potential of pyrolysis oil produced are 7,769,183 L/year and 23,574 L/day, the electrical energy produced is 186,331 kWh/day. The results of the analysis of economic aspects on the net present value of Rp. 310,503,918,563, for an internal rate of return of 30.24%, and for a payback period of 5 months the return on investment.
SIMULASI PERANCANGAN SISTEM PEMBANGKIT LISTRIK TENAGA SURYA ON-GRID PADA BARBERSHOP GAUL DENGAN MENGGUNAKAN HELIOSCOPE : Desain Sistem PLTS On-Grid pada Barbershop Gaul dengan menggunakan Helioscope Vito Arnando
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.528

Abstract

Indonesia is a tropical country where Indonesia has summer with an average radiation of 4.5 kwh/m2 per day. Based on this, Indonesia is classified as a country that has abundant potential for solar energy so that the most suitable and most efficient generator to use is a solar power plant. Barbershop Gaul is a building that is used as a pilot for the object of research in this project. This building has high electricity consumption so that the difference between income and expenses for electricity consumption is often a deficit. The amount of electricity consumption is contributed by several existing electronic equipment including shaving machines, air conditioners, water pumps and so on. To overcome this problem, this project aims to produce a PLTS system design using a simulation method using the helioscope application. In addition to producing a system design, this project further produces an overview of the monthly PLTS energy production, a summary of the system, power loss sources to its economic analysis including initial investment costs, payback period and potential profits that can be obtained. After carrying out this project, it was concluded that the On-Grid PLTS at Barbershop Gaul produces 1,243.8 kWh of electrical energy annually with an energy consumption of 2,662 kWh/year. Thus if a PLTS is installed, the electrical energy used from the PLTS is 1,243.8 kWh and the remaining 1,418.2 kWh is supplied by PLN so Barbershop Gaul needs to pay IDR 3,600,000 to PLN for electricity consumption. However, with the savings generated by implementing the ON-grid system, the business owner only pays Rp. 1,682,593/year. For the initial investment issued in the installation of PLTS, it is Rp. 19,094,480 with Return Of Investment 11.3 Years or 11 Years 3 months
Pemanfaatan Limbah Kulit Singkong Menjadi Bahan Bakar Bioethanol (Studi Kasus : Usaha Keripik Singkong Pika Kota Pekanbaru): Pemanfaatan Limbah Kulit Singkong Menjadi Bahan Bakar Bioethanol (Studi Kasus : Usaha Keripik Singkong Pika Kota Pekanbaru) Mugandi, Nabila Meitri
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.693

Abstract

UKSP is a business that produces 200-300 kg of cassava chips, resulting in 30-45 kg of cassava peel solid waste. The waste is simply thrown away without further processing, causing environmental damage and producing a foul odour. This research utilises cassava peel waste into bioethanol using fermentation and distillation methods. The calculation of electrical energy and cost savings in this study compares E0, E10 and PLN electricity. Bioethanol potential from 30 kg of cassava peel waste is 5.3280 L/h with a purity of 99.9917%. The potential electrical energy generated using E0 reaches 47.34 kWh, while E10 is 46.89 kWh, and PLN electricity is 1.8 kWh. The fuel cost of E0 was IDR 44,4400 for E10 was IDR 33,000 and PLN electricity was IDR 24,336. The results of the comparison between E0 and E10 are used if electricity tariffs increase in the future so that bioethanol can be utilised as alternative energy for UKSP. Based on the results obtained, E10 is an efficient fuel blend that is feasible to use. In the cost analysis, the total investment in cassava peel utilisation is IDR 3,668,895 and the potential savings per year reaches IDR 5,259,024. The pay-back period is 0.70 years. Keyword: Fuel, Bioethanol, Cassava Waste, Electricity, Superpro
Analisis Potensi Minyak Jelantah Sebagai Bahan Baku Produksi Biodiesel di Kota Pekanbaru : Analisis Potensi Minyak Jelantah Sebagai Bahan Baku Produksi Biodiesel di Kota Pekanbaru Tegar Setiadi, Rexy; Nanda Putri Miefthawati
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 1 (2023): IJEERE Juni 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i1.713

Abstract

Fuel Oil is a basic need for society, with a consumption rate of 42% in Indonesia. The high level of consumption, especially for diesel fuel, with supplies and availability of raw materials dwindling makes scarcity a common phenomenon in urban areas. Alternative innovations in the supply of raw materials need to be carried out, one of which is by using alternative raw materials in the form of Biodiesel derived from urban waste cooking oil. The aim of this research is to utilize the 40,000 Kg/month waste of used cooking oil in Pekanbaru City to be converted into Biodiesel with the Transesterification Method in the form of a chemical reaction Fat reacted with methanol and catalyst with the help of Superpro Design software is capable of producing a volume of biodiesel of 33,407 liters per month, a fuel density of 866/km3 with a production cost of IDR 6,000/liter and a selling price of IDR 11,000 per liter which has the potential to make biodiesel an alternative to diesel for the people of Pekanbaru City.
PERANCANGAN PEMASANGAN POMPA AIR BERSUMBER LISTRIK TENAGA MATAHARI DI PERSAWAHAN DESA SIRAISAN : Perancangan Pemasangan Pompa Air Bersumber Listrik Tenaga Matahari Di Persawahan Desa Siraisan hasibuan, fardin
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 2 (2023): IJEERE December 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i2.889

Abstract

Rice is a basic need in Indonesia. Siraisan Village, Ulu Barumun Sub-District, North Sumatra Province, is an area where most of the people are rice farmers. The success of rice planting need water to watering the rice field area, the contours of the hilly area become an obstacle in the water supply for the rice field area. The power grid that is not yet available in the rice field area, resulting in artificial irrigation is difficult to do, for that a special power plant is needed, the power plant used is a Solar Power Panel (PV), a pump can be installed to pump water from the river to irrigation the rice field area. The distance from river to rice field area about 315 meters and a height 3 meters from the normal river lip, results head loss 4.8 m , with a pipe diameter 4 inches. The coverage area of the rice field to be watered is 3 ha with a pump discharge of 600 liters / seconds, head 9 meters, power 3000 watts, AC one phase. The solar power plant is installed on 16 solar cell modules and investment cost Rp 131.996.483,00
Implementasi Sistem Barcode pada Perusahaan Perkebunan Kelapa Sawit untuk Meningkatkan Efisiensi Serta hubungannya dengan Smart People : Implementasi Sistem Barcode pada Perusahaan Perkebunan Kelapa Sawit untuk Meningkatkan Efisiensi Serta hubungannya dengan Smart People NASUTION, ANISAH
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 2 (2023): IJEERE December 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i2.932

Abstract

The use of innovative technology such as the barcode system has the potential to increase the efficiency of palm oil companies and support the realization of smart people. To better understand the impact of barcode system implementation, a qualitative study was conducted. In this study, a qualitative research method was used with a case study approach to explore the implementation of a barcode system in oil palm plantation companies. The qualitative research method was chosen because it can produce more in-depth data and prioritize face-to-face interviews with several informants to get a true and in-depth picture of various perspectives and situations. This study aims to determine the impact of implementing a barcode system on efficiency and smart people. This study used a sample of 4 companies. Based on validity, reliability, relevance of findings, contribution to knowledge and quality of writing, the success percentage of qualitative research is 83%. The results of the study show that the implementation of the barcode system has an impact on efficiency and improvement of human resources through the development of smart people. These findings can be useful for further development of the barcode system, and it is recommended that other palm oil companies adopt this technology.
Temperature Control System for Water Heater with Servo Valve using PID Method: Sistem Pengendalian Suhu Pada Pemanas Air Dengan Servo Valve Menggunankan Metode PID Pranda Prasetyo
Indonesian Journal of Electrical Engineering and Renewable Energy (IJEERE) Vol 3 No 2 (2023): IJEERE December 2023
Publisher : Institut Riset dan Publikasi Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.57152/ijeere.v3i2.945

Abstract

In cold areas, hot water is an essential requirement. Generally warm or hot water is used for bathing, washing, or other household purposes. In general, there are various types of water heaters when viewed from the source of energy, some of which use solar, gas and electricity. In this study, a water heating system was created by adjusting the input water using a servo valve, so it is expected that the water heating will work faster and the resulting performance can be more stable. The smaller the servio angle, the faster the water heating occurs. The expected temperature is between 30 and 60 °C. This system uses the PID method to control the temperature. From the results of the PID control test on sample data, the set point value is 40?C with a Kp value = 0.02, a Ti value = 80 and a Td value = 20. The temperature that has been given by the PID control tries to maintain the set point temperature which has been set at 40 ?C . With values of Kp, Ti, and Td above the temperature can reach the setpoint within (±) 30 minutes.