cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
Istadi
Contact Email
istadi@che.undip.ac.id
Phone
+6281316426342
Journal Mail Official
bcrec@live.undip.ac.id
Editorial Address
Editorial Office of Bulletin of Chemical Reaction Engineering & Catalysis Laboratory of Plasma-Catalysis (R3.5), UPT Laboratorium Terpadu, Universitas Diponegoro Jl. Prof. Soedarto, Semarang, Central Java, Indonesia 50275
Location
Kota semarang,
Jawa tengah
INDONESIA
Bulletin of Chemical Reaction Engineering & Catalysis
Published by Masyarakat Katalis Indonesia - Indonesian Catalyst Society
ISSN : -     EISSN : 19782993     DOI : https://doi.org/10.9767/bcrec
Core Subject : Science, Engineering,
Chemical Engineering, Chemistry & Bioengineering Chemistry
Bulletin of Chemical Reaction Engineering & Catalysis, a reputable international journal, provides a forum for publishing the novel technologies related to the catalyst, catalysis, chemical reactor, kinetics, and chemical reaction engineering. Scientific articles dealing with the following topics in chemical reaction engineering, catalysis science, and engineering, catalyst preparation method and characterization, novel innovation of chemical reactor, kinetic studies, etc. are particularly welcome. However, articles concerned on the general chemical engineering process are not covered and out of the scope of this journal. This journal encompasses Original Research Articles, Review Articles (only selected/invited authors), and Short Communications, including: fundamentals of catalyst and catalysis; materials and nano-materials for catalyst; chemistry of catalyst and catalysis; surface chemistry of catalyst; applied catalysis; applied bio-catalysis; applied chemical reaction engineering; catalyst regeneration; catalyst deactivation; photocatalyst and photocatalysis; electrocatalysis for fuel cell application; applied bio-reactor; membrane bioreactor; fundamentals of chemical reaction engineering; kinetics studies of chemical reaction engineering; chemical reactor design (not process parameter optimization); enzymatic catalytic reaction (not process parameter optimization); kinetic studies of enzymatic reaction (not process parameter optimization); the industrial practice of catalyst; the industrial practice of chemical reactor engineering; application of plasma technology in catalysis and chemical reactor; and advanced technology for chemical reactors design. However, articles concerned about the "General Chemical Engineering Process" are not covered and out of the scope of this journal.
Arjuna Subject : Teknik Kimia (semua kategori) - Katalisis
Articles 838 Documents
 14   15   16   17   18 
Catalytic Polymerization of Acrylonitrile by Khulays Bentonite Matar M. Al-Esaimi
Bulletin of Chemical Reaction Engineering & Catalysis 2007: BCREC: Volume 2 Issue 1 Year 2007 (June 2007)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.2.1.4.6-10

Abstract

The aqueous polymerization of acrylonitrile (AN) catalyzed with exchanged Khulays bentonite . The influence of various polymerization parameters ( e.g., concentrations of Potassium Persulfate (K2S2O8) and monomer , various of organic solvents, and different temperature has been investigated. It was found that the rate of polymerization of AN was found to be dependent on monomer concentration, initiator and temperature. The activation energy of polymerization was calculated .Thermal properties of the polymer were studied by TGA and DSC techniques. © 2007 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0)
Kinetic Study of SN2 Reaction between Paranitrophenyl Benzoate and Hydrazine in the Presence of CTAB Reverse Micelles K. Bhargavi; P. Shyamala; M. Padma; K. V. Nagalakshmi
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 4 Year 2021 (December 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.4.11036.744-751

Abstract

Kinetic study of the reaction between p-Nitrophenyl benzoate (PNPB) by hydrazine (HYN) in the presence of Cetyltrimethylammonium bromide (CTAB)/Chloroform/Hexane reverse micellar medium shows that the reaction obeys first order kinetics with respect to each of the reactants. The rate of the reaction is much slower in reverse micellar medium compared to aqueous medium under identical conditions (kˈAq = 2.84×10−3 sec−1, krm =1.34×10−4 sec−1). The rate constants for the reaction in the reverse micellar medium have been determined at different values of W {W=[H2O]/[CTAB]} and at different concentrations of CTAB. It was found that the observed rate constant decreases with W. This kinetic behaviour was interpreted by using modified Berezin pseudo phase model, taking into consideration the distribution of the reactants, PNPB and hydrazine between the three pseudo phases, i.e., water pool, interface an organic phase. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Utilization of Renewable and Waste Materials for Biodiesel Production as Catalyst Prashant Kumar; Anil Kumar Sarma; M. K. Jha; Ajay Bansal; Bharvee Srivastava
Bulletin of Chemical Reaction Engineering & Catalysis 2015: BCREC Volume 10 Issue 3 Year 2015 (December 2015)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.10.3.8584.221-229

Abstract

The efficient and economic utilization of natural renewable and waste materials of various industries and biomass having non-homogeneous composition is a new dimension of research for biodiesel pro- duction. A combination of these renewable, waste materials and traditional heterogeneous catalyst can also be looked after for the possible solution of heterogeneous catalytic transesterification. This review discusses industrially derived and naturally occurring materials containing calcium, sodium, potassium etc, which were found instrumental for biodiesel production. About 60 research articles and patents have been reviewed and the findings are analysed in this article for developing industrial scale heterogeneous catalytic pilot plant facilities for biodiesel production. © 2015 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Effect of Calcination Temperature on Performance of Photocatalytic Reactor System for Seawater Pretreatment Weerana Eh Kan; Jamil Roslan; Ruzinah Isha
Bulletin of Chemical Reaction Engineering & Catalysis 2016: BCREC Volume 11 Issue 2 Year 2016 (August 2016)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.11.2.554.230-237

Abstract

Conservative desalination technology including distillation requires high energy and cost to operate. Hence, pretreatment process can be done prior to desalination to overcome energy demand and cost reduction. Objective of this research is to study the effect of calcination temperature of hybrid catalyst in photocatalytic reactor system in the seawater desalination, i.e. salt removal in the seawater. The catalyst was synthesized via wet impregnation method with 1:1 weight ratio of TiO2 and activated oil palm fiber ash (Ti:Ash). The catalyst was calcined at different temperature, i.e. 500 oC and 800 oC. The study was carried out in a one liter Borosilicate photoreactor equipped with mercury light of 365 nanometers for two hours with 400 rpm mixing and catalyst to seawater sample weight ratio of 1:400. The Chemical Oxygen Demand (COD), pH, dissolved oxygen (DO), turbidity and conductivity of the seawater were analyzed prior and after the testing. The fresh and spent catalysts were characterized via X-Ray Diffractogram (XRD and Nitrogen physisorption analysis. The calcination temperature significantly influenced the adsorption behaviour and photocatalytic activity. However, Ti:Ash which calcined at 800 oC has less photocatalytic activity. It might be because the surface of fiber ash was sintered after calcined at high temperature. The Ti:Ash catalyst that calcined at 500 oC was found to be the most effective catalyst in the desalination of seawater by reducing the salt concentration of more than 9 % compared to Ti:Ash calcined at 800 oC. It can be concluded that catalyst calcination at 500 °C has better character, performance and economically feasible catalyst for seawater desalination. 
Microwave-Assisted Synthesis of DUT-52 and Investigation of Its Photoluminescent Properties Ruth Febriana Kesuma; Aep Patah; Yessi Permana
Bulletin of Chemical Reaction Engineering & Catalysis 2019: BCREC Volume 14 Issue 1 Year 2019 (April 2019)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.14.1.2369.124-129

Abstract

A zirconium metal-organic framework (MOF) of DUT-52 (DUT: Dresden University of Technology) was synthesized herein by reacting zirconium tetrachloride (ZrCl4) and 2,6-naphthalenedicarboxylic acid (H2NDC) in DMF under microwave heating at 115 oC for 25 min. This synthetic procedure was more efficient than a solvothermal method, by which a long thermal exposure (24 h) of 100-150 oC was required to produce the same MOF. The MOF has a thermal stability of 560 °C, prior to partial loss of interconnected 2,6-naphthalenedicarboxylate (NDC) linkers at some structure building units (SBU). Crystallinity of this DUT-52 was ca. 77 %, which was the same as one synthesized solvothermally.  Diffuse Reflectance UV-Vis spectra revealed an absorption at λex of 287 nm, which was equivalent to a bandgap energy of 4.32 eV.  Electron excitations of this DUT-52 at 275 and 300 nm gave emission wavelength of 433 nm (a purple region),  indicating a prospective use of DUT-52 as a photoluminescent material. 
Synthesis and Characterization of High Aluminum Zeolite X from Technical Grade Materials Seyed Kamal Masoudian; Sepehr Sadighi; Ali Abbasi
Bulletin of Chemical Reaction Engineering & Catalysis 2013: BCREC Volume 8 Issue 1 Year 2013 (June 2013)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.8.1.4321.54-60

Abstract

Zeolites are widely used as ion exchangers, adsorbents, separation materials and catalyst due to their well-tailored and highly-reproducible structures; therefore, the synthesis of zeolite from low grade resources can be interested. In the present work, high aluminum zeolite X was prepared from mixing technical grade sodium aluminate and sodium silicate solutions at temperatures between 70°C and 100°C. The synthesized zeolite X was characterized by SEM and X-ray methods according to ASTM standard procedures. The results showed that aging of the synthesis medium at the room temperature considerably increased the selectivity of zeolite X formation. On the other hand, high temperature of reaction mixture during crystallization formed zeolite A in the product; therefore, it decreased the purity of zeolite X. In addition, it was found that increasing H2O/Na2O and decreasing Na2O/SiO2 molar ratios in the reaction mixture resulted product with higher purity. © 2013 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0)
Effects of Platinum and Palladium Metals on Ni/Mg1-xZrxO Catalysts in the CO2 Reforming of Methane Faris Jasim Abdulridha Al-Doghachi
Bulletin of Chemical Reaction Engineering & Catalysis 2018: BCREC Volume 13 Issue 2 Year 2018 (August 2018)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.13.2.1656.295-310

Abstract

Nickel, palladium, and platinum catalysts (1 wt.% each) supported on MgO and MgZrO to prepare Pt,Pd,Ni/Mg1-xZrxO catalysts (where x = 0, 0.03, 0.07, and 0.15), were synthesized by using co-precipitation method with K2CO3 as the precipitant. X-ray diffraction (XRD), X-ray fluorescence (XRF), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), H2-temperature programmed reduction (H2-TPR), and thermo gravimetric analysis (TGA) were employed to observe the characteristics of the prepared catalysts. The Pt,Pd,Ni/Mg0.85Zr0.15O showed the best activity in dry reforming of methane (DRM) with 99 % and 91 % for CO2 and CH4 conversions, respectively and 1.28 for H2/CO ratio at temperature 900 °C and 1:1 of CH4:CO2 ratio. The stability of Pt,Pd,Ni/Mg0.85Zr0.15O catalyst in the presence and absence of low stream 1.25 % oxygen was investigated. Carbon formation and amount in spent catalysts were examined by TEM and TGA in the presence of stream oxygen. The results showed that the amount of carbon was suppressed and negligible coke formation (less than 3 %) was observed. Several effects were observed with ZrO2 use as a promoter in the catalyst. Firstly, the magnesia cubic phase stabilized. Secondly, thermal stability and support for basicity increased. Thirdly, carbon deposition and the reducibility of Ni2+, Pd2+, and Pt2+ ions decreased. 
Synthesis of Porous N-doped TiO2 by Using Peroxo Sol-Gel Method for Photocatalytic Reduction of Cd(II) Diana Vanda Wellia; Dina Nofebriani; Nurul Pratiwi; Safni Safni
Bulletin of Chemical Reaction Engineering & Catalysis 2022: BCREC Volume 17 Issue 1 Year 2022 (March 2022)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.17.1.12347.103-112

Abstract

Porous N-doped TiO2 photocatalyst was successfully synthesized by an environmentally friendly peroxo sol-gel method using polyethylene glycol (PEG) as a templating agent. Here, the effect of PEG addition to the aqueous peroxotitanium solutions on the structure, pore properties and photocatalytic activity of the obtained photocatalysts was systematically studied. The prepared photocatalysts were characterized by X-ray diffraction (XRD), UV-Vis diffuse reflectance spectroscopy (DRS), and Brunauer-Emmett-Teller (BET). It was found that the doping of nitrogen narrows the band gap of TiO2 leading to enhance its visible-light response. The BET analysis shows that the prepared photocatalysts have a typical mesoporous structure with pore sizes of 3–6 nm. The photocatalytic activity of the prepared photocatalysts was evaluated by photocatalytic reduction of Cd(II) in an aqueous solution under visible light irradiation. The results show that porous N-doped TiO2 with the optimal PEG addition had the highest Cd(II) reduction of 85.1% after 2.5 h irradiation in neutral aqueous solution. This significant improvement in photocatalytic activity of the prepared photocatalysts was mainly attributed to the synergistic combination of N doping and porous structure, which could actively increase the catalytic active site of this photocatalysts. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Preparation of Reducing Sugar Hydrolyzed from High-Lignin Coconut Coir Dust Pretreated by the Recycled Ionic Liquid [mmim][dmp] and Combination with Alkaline Hanny F. Sangian; Junaidi Kristian; Sukmawati Rahma; Hellen Kartika Dewi; Debra Arlin Puspasari; Silvya Yusnica Agnesty; Setiyo Gunawan; Arief Widjaja
Bulletin of Chemical Reaction Engineering & Catalysis 2015: BCREC Volume 10 Issue 1 Year 2015 (April 2015)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.10.1.7058.8-22

Abstract

This study aims to produce reducing sugar hydrolyzed from substrate, coconut coir dust pretreated by recycled ionic liquid and its combination with alkaline. The 1H NMR and FTIR were performed to ver-ify the synthesized ionic liquid methylmethylimidazolium dimethyl phosphate ([mmim][dmp]). The structure of pretreated substrates was analyzed by XRD measurement. The used ionic liquid was recy-cled twice to re-employ for substrate pretreatment. The treated- and untreated-coconut coir dust were hydrolyzed into sugars using pure cellulase. The reaction, which called an enzymatic hydrolysis, was conducted at 60 °C, pH 3, for 48 h. The yields of sugar hydrolyzed from fresh IL-pretreated, 1R*IL-pretreated and 2R*IL-pretreated substrates were of 0.19, 0.15 and 0.15 g sugar / g cellu-lose+hemicellulose, respectively. Pretreatment with NaOH or the combination of NaOH+IL resulted in yields of reducing sugars of 0.25, 0.28 g/g, respectively. When alkaline combined with the recycled ionic liquids, NaOH+1R*IL, NaOH+2R*IL in the pretreatment, the yields of sugar were relatively similar to those obtained using alkaline followed by fresh ionic liquid. If the mixture enzymes, cellu-lase+xylanase, used to liberate sugars from fresh IL-pretreated, or recycled IL-pretreated substrates, the amount of sugar (concentration or yield) increased slightly compared to that employing a single cel-lulase. These findings showed that recycled IL pretreatment of the high-lignin lignocellulose, coconut coir dust, is a new prospect for the economical manufacture of fermentable sugars and biofuel in the coming years. © 2015 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0)
Preparation of Biofuel from Palm Oil Catalyzed by Ammonium Molybdate in Homogeneous Phase Sepehr Sadighi; Seyed Kamal Masoudian Targhi
Bulletin of Chemical Reaction Engineering & Catalysis 2017: BCREC Volume 12 Issue 1 Year 2017 (April 2017)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.12.1.486.49-54

Abstract

Producing transportation fuels from bio sources was of prime importance due to the strict environmental legislations for producing clean fuels from conventional oil resources. However, the economical impacts of the biofuel production should be considered. In this study, the production of bio-naphtha and biodiesel from palm oil using homogeneous catalyst, i.e. an aqueous phase of ammonium molybdate, was studied. This catalyst was prepared by dissolving sodium molybdate in de-ionized water with hydrochloric acid, and then neutralizing the mixture with ammonium hydroxide. The solution was dried at 90 °C for 24 h to obtain ammonium molybdate. Then, characterization of the catalyst was done by informative techniques, such as XRD and FT-IR. The results showed that the main phase of the synthesized catalyst was molybdate ammonium hydrates (4MoO3.2NH3.H2O), and also bands of Mo–O, Mo–O–Mo, N–H and surface hydroxyl groups were observed in the sample. Moreover, activity test confirms that the bio-naphtha produced from the proposed method has a few aromatic components, and its sulfur content was negligible. Moreover, ash, nitrogen, sulfur and carbon residue were not detected in the produced biodiesel, and its Cetane index was 66.3. Therefore, it was a suitable fuel for diesel engines vehicles. 

Page 16 of 84 | Total Record : 838

 14   15   16   17   18 

Filter by Year

2007 2026


Reset
Filter By Issues
All Issue 2026: BCREC Volume 21 Issue 3 Year 2026 (October 2026) (Issue in Progress) 2026: BCREC Volume 21 Issue 2 Year 2026 (August 2026) 2026: BCREC Volume 21 Issue 1 Year 2026 (April 2026) 2026: Just Accepted Manuscript and Article In Press 2026 2025: BCREC Volume 20 Issue 4 Year 2025 (December 2025) 2025: BCREC Volume 20 Issue 3 Year 2025 (October 2025) 2025: BCREC Volume 20 Issue 2 Year 2025 (August 2025) 2025: BCREC Volume 20 Issue 1 Year 2025 (April 2025) 2024: BCREC Volume 19 Issue 4 Year 2024 (December 2024) 2024: BCREC Volume 19 Issue 3 Year 2024 (October 2024) 2024: BCREC Volume 19 Issue 2 Year 2024 (August 2024) 2024: BCREC Volume 19 Issue 1 Year 2024 (April 2024) 2023: BCREC Volume 18 Issue 4 Year 2023 (December 2023) 2023: BCREC Volume 18 Issue 3 Year 2023 (October 2023) 2023: BCREC Volume 18 Issue 2 Year 2023 (August 2023) 2023: BCREC Volume 18 Issue 1 Year 2023 (April 2023) 2022: BCREC Volume 17 Issue 4 Year 2022 (December 2022) 2022: BCREC Volume 17 Issue 3 Year 2022 (September 2022) 2022: BCREC Volume 17 Issue 2 Year 2022 (June 2022) 2022: BCREC Volume 17 Issue 1 Year 2022 (March 2022) 2021: BCREC Volume 16 Issue 4 Year 2021 (December 2021) 2021: BCREC Volume 16 Issue 3 Year 2021 (September 2021) 2021: BCREC Volume 16 Issue 2 Year 2021 (June 2021) 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021) 2020: BCREC Volume 15 Issue 3 Year 2020 (December 2020) 2020: BCREC Volume 15 Issue 2 Year 2020 (August 2020) 2020: BCREC Volume 15 Issue 1 Year 2020 (April 2020) 2019: BCREC Volume 14 Issue 3 Year 2019 (December 2019) 2019: BCREC Volume 14 Issue 2 Year 2019 (August 2019) 2019: BCREC Volume 14 Issue 1 Year 2019 (April 2019) 2018: BCREC Volume 13 Issue 3 Year 2018 (December 2018) 2018: BCREC Volume 13 Issue 2 Year 2018 (August 2018) 2018: BCREC Volume 13 Issue 1 Year 2018 (April 2018) 2017: BCREC Volume 12 Issue 3 Year 2017 (December 2017) 2017: BCREC Volume 12 Issue 2 Year 2017 (August 2017) 2017: BCREC Volume 12 Issue 1 Year 2017 (April 2017) 2016: BCREC Volume 11 Issue 3 Year 2016 (December 2016) 2016: BCREC Volume 11 Issue 2 Year 2016 (August 2016) 2016: BCREC Volume 11 Issue 1 Year 2016 (April 2016) 2015: BCREC Volume 10 Issue 3 Year 2015 (December 2015) 2015: BCREC Volume 10 Issue 2 Year 2015 (August 2015) 2015: BCREC Volume 10 Issue 1 Year 2015 (April 2015) 2014: BCREC Volume 9 Issue 3 Year 2014 (December 2014) 2014: BCREC Volume 9 Issue 2 Year 2014 (August 2014) 2014: BCREC Volume 9 Issue 1 Year 2014 (April 2014) 2013: BCREC Volume 8 Issue 2 Year 2013 (December 2013) 2013: BCREC Volume 8 Issue 1 Year 2013 (June 2013) 2013: BCREC Volume 7 Issue 3 Year 2013 (March 2013) 2012: BCREC Volume 7 Issue 2 Year 2012 (December 2012) 2012: BCREC Volume 7 Issue 1 Year 2012 (June 2012) 2011: BCREC Volume 6 Issue 2 Year 2011 (December 2011) 2011: BCREC Volume 6 Issue 1 Year 2011 (June 2011) 2010: BCREC Volume 5 Issue 2 Year 2010 (December 2010) 2010: BCREC Volume 5 Issue 1 Year 2010 (June 2010) 2009: BCREC Volume 4 Issue 2 Year 2009 (December 2009) 2009: BCREC Volume 4 Issue 1 Year 2009 (June 2009) 2008: BCREC Volume 3 Issue 1-3 Year 2008 (December 2008) 2007: BCREC: Volume 2 Issues 2-3 Year 2007 (October 2007) 2007: BCREC: Volume 2 Issue 1 Year 2007 (June 2007) More Issue