cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota bekasi,
Jawa barat
INDONESIA
JREC (Journal of Electrical and Electronics)
ISSN : 23025883     EISSN : 25500899     DOI : -
Core Subject : Engineering,
Arjuna Subject : -
Articles 182 Documents
ANTENA MIKROSTRIP SINGLE LAYER DUAL BAND UNTUK KOMUNIKASI SATELIT PADA SPEKTRUM S-BAND DAN KU-BAND Marini, Sri; Asrika, Sukwati Dewi; Sikki, Muhammad Ilyas
JREC (Journal of Electrical and Electronics) Vol 6 No 2 (2018): JREC (Journal of Electrical and Electronics)
Publisher : JREC (Journal of Electrical and Electronics)

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1535.866 KB)

Abstract

Antena mikrostrip adalah suatu konduktor metal yang menempel diatas ground plane yang diantaranya terdapat bahan dielektrik. Antena mikrostrip merupakan antena yang memiliki masa ringan, mudah untuk difabrikasi, dengan sifatnya yang konformal sehingga dapat ditempatkan pada hampir semua jenis permukaan dan ukurannya kecil dibandingkan dengan antena jenis lain. Karena sifat yang dimilikinya, antena mikrostrip sangat sesuai dengan kebutuhan saat ini sehingga dapat diintegrasikan dengan peralatan telekomunikasi. Antena Mikrostrip single layer untuk Satelite Communication Mobile beroperasi pada S-Band dan Ku Band, pada frekuensi center kerja 2,4 GHz dan 17,1 GHZ dengan Nilai VSWR 1,1 dan Nilai Return loss ≤ -10 dB Perancangan Antena menggunakan CST Microwave Studio.   Microstrip antenna is a metal conductor attached to the ground plane which includes dielectric material. Microstrip antenna is an antenna that has a light mass, is easy to fabricate, with a conformal nature so that it can be placed on almost any type of surface and its size is small compared to other types of antennas. Because of its properties, microstrip antennas are very suitable with current requirements so that they can be integrated with telecommunications equipment. Single layer Microstrip Antenna for Satellite Communication Mobile Operates on S-Band and Ku Band, at 2.4 GHz and 17.1 GHZ Working Center Frequency with 1.1 VSWR Value and Return loss Value ≤ -10 dB Antenna Design using CST Microwave Studio.
SISTEM INFORMASI RUTE BUS TRANSJAKARTA MENGGUNAKAN METODE RAPID APPLICATION DEVELOPMENT Lubis, Hendarman; Rianti, Susi; Esrayanti, Esrayanti
JREC (Journal of Electrical and Electronics) Vol 6 No 2 (2018): JREC (Journal of Electrical and Electronics)
Publisher : JREC (Journal of Electrical and Electronics)

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (872.139 KB)

Abstract

Pengembangan sistem informasi rute bus transjakarta yang terintegrasi dengan google maps dalam bentuk aplikasi berbasis android bertujuan untuk meningkatkan informasi masyarakat dalam penggunaan bus transjakarta, mempermudah masyarakat umum dalam pencarian rute dan peta transit bus transjakarta. Sistem informasi rute bus transjakarta yang terintegrasi dengan google maps menjadi solusi atas kelemahan pada sistem yang sebelumnya sudah dibangun. Metode pengumpulan data yang digunakan dalam penelitian ini, yaitu observasi, wawancara, studi pustaka, studi literatur, kuisioner, dan metode pengembangan sistem. Metode pengembangan sistem yang digunakan dalam pengembangan sistem informasi rute bus transjakarta ini adalah metode RAD (Rapid Application Development). Pengujian fungsional sistem dilakukan menggunakan black box testing. Dengan dilakukannya pengembangan sistem informasi rute bus transjakarta yang terintegrasi dengan google maps, masyarakat umum dapat dengan mudah mendapatkan informasi rute bus transjakarta dan informasi peta transit bus transjakarta.   The development of the Transjakarta bus route information system that is integrated with Google Maps in the form of an Android-based application aims to improve public information on the use of Transjakarta buses, making it easier for the general public in searching routes and maps of Transjakarta bus transit. The Transjakarta bus route information system that is integrated with google maps is a solution to the weaknesses in the system that have previously been built. The method of data collection used in this study is observation, interviews, literature studies, literature studies, questionnaires, and system development methods. The system development method used in the development of the Transjakarta bus route information system is the Rapid Application Development (RAD) method. Functional testing systems are carried out using black box testing. With the development of the Transjakarta bus route information system that is integrated with Google maps, the general public can easily obtain information on the Transjakarta bus route and information on Transjakarta bus transit maps.
SMART ANTENNA MICROSTRIP SWITCH-BEAM MULTIBAND MULTIBEAM DENGAN PHASE ARRAY UNTUK KOMUNIKASI WIRELESS Saragih, Yuliarman; Ibrahim, Ibrahim
JREC (Journal of Electrical and Electronics) Vol 6 No 2 (2018): JREC (Journal of Electrical and Electronics)
Publisher : JREC (Journal of Electrical and Electronics)

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (918.524 KB)

Abstract

Perkembangan antena dimasa depan akan mengarah smart antena, dimana antena mampu menentukan beam mana yang paling kuat. Antena yang bekerja Multiband dan Multibeam menjadi sebuah hal yang mungkin dilakukan untuk perkembangan smart antena. Beam antena dapat berubah karena perubahan fasa, dan dapat diperoleh menggunakan butler matrik. Salahsatu kelemahan antena multiband adalah gainnya yang rendah, untuk meningkatkan gain dapat dilakukan dengan meng-array antena tersebut. Multiband dan multibeamsmartantena dapat diperoleh menggunakan phase array dengan penggunaan butler matiks sebagai perubah phase dan penggunaan antena multiband yang diarray.   The development of the antenna leads to smart antenna, where the antenna is able to determine which beam is the strongest. Antennas that work Multiband and Multibeam are possible for the development of smart antennas. The antenna beams can change due to phase changes, and can be obtained using the butler matrix. One of the disadvantages of a multibans antenna is the low gain, therefore arraying the antenna can be used to increase the gain. Multiband and multibeam can be obtained using phase array with the use of the matler butler as a phase change and the use of an arrayed multiband antenna.
Rancang Bangun Sistem Kendali Berbasis Googlespeech Untuk Aktivasi Peralatan Listrik Rumah Kurniawan, Tesar; Nursin, Nursin; Bakrie, Muhamad Amin; Samsiana, Seta
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1468.636 KB) | DOI: 10.33558/jrec.v5i2.459

Abstract

App inventor adalah media pengembang perangkat lunak untuk sistem android, yang memudahkan para  pengembangnya mengembangkan  idenya,  salah satunya aplikasi yang mampu mengendalikan peralatan listrik rumah menggunakan suara melalui  telepon  pintar  yang dapat mengontrol aktivasi peralatan listrik rumah. Google  Speech  digunakan untuk pengenalan suara yang  kemudian memberikan input ke Arduino untuk mengendalikan aktivasi peralatan listrik rumah, Peralatan listrik rumah seperti lampu, motor pompa akuarium, kipas, door lock dan motor servo yang memanfaatkan relay sebagai driver, kemudian dilakukanlah pengujian dan penelitian pada laporan ini berisi tentang pengujian akurasi pengenalan suara google  Speech dan pengujian jarak koneksi Bluetooth. Tingkat keakurasian pada google  Speech  yang paling baik dari 3 bahasa yaitu Bahasa Indonesia disusulBahasa jawa  dan terakhir Bahasa sunda, sedangkan untuk jarak koneksi pada Bluetooth dapat dioperasikan jarak maksimal pada ruang bebas adalah 20 m dan jarak maksimal pada ruang berhalangan adalah 13 m. App inventor is a software developer media for android systems, which makes it easy for developers to develop their ideas, i.e an application that is able to control home electrical appliances using voice over smart phones that can control the activation of home electrical appliances. Google Speech is used for voice recognition which then provides input to Arduino to control the activation of home electrical appliances, such as lamps, aquarium pump motors, fans, door locks. A servo motors is used as drivers, then test and research on this report Contains about Speech google speech recognition accuracy testing and Bluetooth connection distance testing. Level of accuracy on google Speech the best of 3 languages ie Indonesian followed by Java and last language Sundanese, while for the distance on the Bluetooth connection can be operated the maximum distance in free space is 20 m and the maximum distance in the absence room is 13 m.
PERANCANGAN SISTEM PENDETEKSI PRODUK MIXED-UP BERBASIS HI-SPEED CAMERA KEYENCE CV-H035 MDI AREA PRODUKSI PT. NOK INDONESIA Sanusi, Uci; Sikki, Muhammad Ilyas; Supratno, Setyo
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (832.937 KB)

Abstract

PT. NOK Indonesia merupakan perusahaan manufaktur oil seal dan komponen rubber molding untuk industri otomotif dan non otomotif yang terus berkembang. Pada periode Januari-Juni 2015, bagian produksi area NAL, PT.NOK Indonesia menerima 7 kasus Customer Complaint, 4 kasus merupakan complaint produk mixed-up, antara produk BV05044-I0, BV05044-J0 dan AVQ0026-A0, yang masuk pada kategori critical, Perbaikan yang dilakukan untuk mengatasi permasalahan produk mixed-up adalah dengan membuat sistem pendeteksi produk mixed-up. Sistem ini bekerja menggunakan hi-speed Camera sebagai pengambil citra digital. Citra yang diambil merupakan citra bagian inner produk yang dijadikan acuan sistem. Pengolahan citra digital dilakukan oleh kontrol kamera untuk menentukan citra OK dan NG. Penerapan sistem ini dapat menghilangkan komplainpelanggan produk mixed-up, dari sebelumnya sebanyak 4 kasus menjadi 0 kasus, atau turun 100%. Kata Kunci :komplain, mixed-up, hi-speed camera, Pengolahan citra Digital PT. NOK Indonesia is an oil seal manufacturing company and rubber molding components for the automotive and non automotive industries. In January-June 2015, the production division of NAL area of PT.NOK Indonesia received 7 complaint cases, 4 cases were complaint of mixed-up products, between BV05044-I0, BV05044-J0 and AVQ0026-A0 product which classified as critical categories. Improvements made to overcome the problem of mixed-up products is to create a mixed-up product detection system. This system works using hi-speed Camera as a digital image taker. The image taken is the image of the inner product that is used as the system reference. Digital image processing is done by the camera control to determine the OK and NG image. Implementation of this system can solve Customer Complaintof mixed-up products, from 4 cases become 0 cases, or down 100%. Keywords :Complain, mixed-up, hi-speed camera, digital image processing
SISTEM ABSENSI DOSEN MENGGUNAKAN RADIO FREQUENCY IDENTIFICATION (RFID) BERBASIS WEB Kosasih, Niki; Bakri, Muhammad Amin; Firasanti, Annisa
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1307.582 KB)

Abstract

Tujuan dari penelitian ini adalah merancang suatu sistem absensi dosen dengan menggunakan teknologi RFID berbasis web yang handal dan mudah di aplikasikan ke berbagai macam browser. Metode penelitian yang digunakan dalam penelitian ini adalah percobaan pengambilan data jarak pembacaan, jeda waktu dan pengujian halaman web. Hasil penelitian menunjukan bahwa jarak maksimal pembacaan tag ke RFID reader adalah 4 cm, jeda waktu minimal yang diperlukan dalam pembacaan tag adalah 0,5 detik dan sistem dapat berjalan baik pada browser mozila firefox, chrome dan internet explorer. Kata kunci : Absensi, RFID, web The purpose of this study was to design a faculty attendance system using RFID technology reliable web-based and easily applied to a variety of browsers. The method used in this study is the reading distance experiment data retrieval, time lag and testing web pages. The results showed that the maximum distance to the RFID tag reader reading is 4 cm, the required minimum time lag in reading tag is 0.5 seconds and the system can run both in the browser mozilla firefox, chrome and internet explorer. Keywords: Attendance, RFID, web
RANCANG BANGUN PEMANFAATAN THERMOELECTRIC SEBAGAI PENDINGIN PADA KONTROLMESIN INJECTION PLASTIK STORK 450 TON Sugiyanto, Hengki; Paronda, Abdul Hafid; Samsiana, Seta
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (921.659 KB)

Abstract

Dalam penelitian ini penulis menganalisa penggunaan thermoelektrik untuk menurunkan temperatur pada kontrol mesin injeksi plastik pada mesin stork 450 ton. Penelitian di lakukan mengunakan komponen seperti power supply, exhaust fan, thermostat eldon, thermoelektrik, multitester, heat sink, kabel, tang ampere dan thermometerdigital untuk menganalisa mesin. Temperatur pada kontrol mesin sebelum mengunakan termoelektrik temperatur mesin adalah 52,7oC. Kemudian semua komponen di pasang pada kontrol mesin. Setelah itu di berikan tegangan 2123,5Volt dengan daya 3 ampere sebagai hasilnya temperatur akan menurun menjadi 37,2oC dalam waktu 15 menit. Kesimpulannya pengunaan termoelektrik pada mesinberhasil menurunkan suhu panel kendali. Kata kunci : Termoelektrik, power supply, exhaust fan In this research, the usage of thermoelectric in order to decrease the temperature in injection plastic engine control in 450 tons stork machine is analysed. To do so, this research use several components such as power supply, exhaust fan, eldon thermostat, thermoelectric, multitester, heat sink, cables, current pliers and digital thermometer. The temperature in engine control is 52,7oC before the thermoelectric is applied. Next, all the components is installed in engine control and 21-23,5 Volt voltage and 3 ampere current is given. As a result, the temperature is decreasing into 37,2oC in 15 minutes. Hence the usage of thermoelectric in the engine is successfully decrease the control panel temperature. Keywords :Termoelektrik, power supply, exhaust fan
HMI SCADABERBASIS WEB MENGGUNAKAN VIJEO DESIGNER Aulia, Fahmi; Supratno, Setyo; Suryatini, Fitria
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1458.529 KB)

Abstract

ABSTRAK SistemScada merupakan sistem yang sudah banyak digunakan untuk mengontrol dan memonitoring mesin-mesin di dunia industri, tetapi kontrol dan monitoring tersebut umumnya dilakukan disatu tempat saja. Pada perusahaan yang mempunyai plant-plant yang tersebar di lokasi yang berjauhan, banyak mengalami kesulitan dalam mengontrol plant-plant tersebut. Contoh pada mesin boiler, mesin yang memerlukan pengawasan yang lebih ketat karena mesin ini dapat menimbulkan ledakan jika terjadi kesalahan pada sistem. Perencanaan dan pembuatan penelitian ini membuat simulasi HMI scada untuk mengontrol dan memonitoring pada mesin boiler berbasis web gate yang terhubung melalui komunikasi sistem wireless LAN dan untuk softwere HMI menggunakan Vijeo designer. Dengan menggunakan sistem ini, bahkan sebuah PC yang hanya memiliki IE (Internet Explorer) dapat mengontrol dan memonitoring dimana saja selama masih memiliki jaringan web server. Untuk metode yang diterapkan penulis menggunakan metode eksperimen dengan melakukan pengujian sistem HMI scada berbasis web gate serta menganalisa jarak jangkauan jaringan komunikasi. Dari hasil pengujian dan analisa didapatkan bahwa sistem sesuai dengan perencanaan serta jarak jangkauan jaringan komunikasi maksimal 20 meter. Kata kunci:HMI, Scada, Web gate, Vijeo designer, PC Scada system is a system that has been widely used to control and monitor machines in industry, yet typically they both done concentrated in one place only. When a company has plants that scattered in some distant locations, it will be rather difficult to control the plants. For examples in boiler engines, machines that require more strict supervision because these machines can cause an explosion in case of system errors. This research make HMI scada simulation to control and monitor a web-gate-based boiler machine which is connected via wireless LAN system communication and for HMI softwere using Vijeo designer. Using this system, even a PC which only have IE (Internet Explorer) can do control and monitor anywhere as long as it still has a network web server. The method applied by the author is an experimental method by testing the HMI scada system based on web gate as well as analyzing the distance of network communication range. The results shows that the system is well-performed and the maximum distance network communication coverage is 20 meters. Keywords: HMI, Scada, Web gate, vijeo designer, PC
ANALISIS POWER LOSSES PADA DISTRIBUSI LISTRIK DI GEDUNG UNIVERSITAS ISLAM “45” BEKASI DENGAN MENGGUNAKAN SOFTWARE ETAP 7.5.0 Supriyadi, Supriyadi; Paronda, Abdul Hafid; Hasad, Andi
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (871.765 KB)

Abstract

Analisis power losses dimaksudkan untuk memperoleh informasi mengenai kerugian daya pada jaringan listrik di Universitas Islam ?45? Bekasi. Manfaat dari analisis power losses adalah untuk mengetahui kondisi suatu jaringan listrik dan untuk mengetahui besar power losses akibat kabel penghantar serta upaya pengurangan power losses. Perhitungan power losses saat ini banyak menggunakan aplikasi komputer, tujuannya untuk mempermudah dan mendapatkan hasil yang lebih akurat, sehingga dalam penelitian ini digunakan Software ETAPS 7.50. Kesimpulan yang diambil dari penelitian ini adalah tentang kondisi jaringan listrik di Universitas Islam ?45? Bekasi yang menunjukkan bahwa power losses yang diakibatkan kabel penghantar secara keseluruhan adalah sebesar 110 watt. Kemudian salah satu cara mengurangi power losses yaitu dengan mengganti jenis kabel dari bahan aluminium menjadi tembaga dan dari hasil simulasi ETAPS 7.50 menunjukan penurunan power losses. Kata Kunci :Power losses, ETAPS 7.50., Distribusi Listrik Power Losses analysis is conducted to obtain information about power losses in power grid at Islamic University "45" Bekasi. The benefit is to gain information of one electricity network and the amount of power losses occurs from carrier cables in order to reduce the power losses. Nowadays, it usually performed by computer software, to simplify the process and to gain more accurate results. In this research, the application used is ETAPS 7.50. The conclusion drawn from this research is about the condition of the power grid in Islamic University "45" Bekasi which shows the power of loss caused by the conductor cable is 110 watts. Thus one way to reduce power losses is to replace the cable from aluminum to copper and from the simulation result in ETAPS 7.50 indicates a decrease in power losses. Keywords: Power losses, ETAPS 7.50, electrical distribution
ANALISA DAN PERANCANGAN ANTENA MIKROSTRIP MULTIWIDEBAND DENGAN PATCH SLOT DOUBLE LAYER UNTUK JARINGAN 5G Marini, Sri; Supratno, Setyo
JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics)
Publisher : Program Studi Teknik Elektro Fakultas Teknik Universitas Islam 45 Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (833.02 KB)

Abstract

Rancang bangun antenna mikrostrip untuk aplikasi 5G dikembangkan untuk mendukung komunikasi data pada perangkat komunikasi wireless. Antena dirancang agar mampu beroperasi pada range frekuensi3 ? 10 GHz. Pada penelitian ini penulis merancang suatu antenna mikrostrip patch slot. Konfigurasi dari sebuah rancangan antenna pada penelitian ini dengan cara teknik coupling proximity menggunakan dua lapisan substrat dari FR4 dengan ketebalan 0.16 cm dan konstanta dielektrik 2.2. Dimana lapisan substrat bagian atas untuk patch slot dan substrat bawah untuk catu saluran transmisi. Menggunakan teknik pencatuan yang mampu membuat matching impedance yang optimal.Untuk perancangan antenna mikrostrip dilakukan dengan menggunakan dua metode yaitu simulasi dan pengukuran. Metode simulasi merupakan aplikasi dari perancangan dan metode dengan aplikasi perangkat lunak HFSS versi 13.Dari hasil simulasi diperoleh parameter antenna seperti bandwidthdari return loss dibawah -10 dB diperoleh single band return loss, dan untuk VSWR 1 sampai 2 diperoleh hasil simulasi terendah adalah 1.1 dicapai pada frekuensi 9,8 GHz. Polaradiasi yang dihasilkan yaitu lobe. Dari hasil pengukuran diperoleh nilai ?nilai pada grafik return loss dengan bandwidth operasi (return loss < -10 dB) yaitu band dengan karakteristik millimeter wave (> 1 GHz) pada band operasi 3,5 ? 9.6 GHz (6.1 GHz). Kata kunci :Antena mikrostrip, coupling proximity, Patch Dual U? Slot, multiwide-band 5G The design of microstrip antennas for 5G applications was developed to support data communications on wireless communication devices. The antenna is designed to operate at a frequency range of 3 - 10 GHz. In this study the authors designed a microstrip patch slot antenna. Configuration of an antenna design in this study by means of coupling proximity technique using two substrate layer of FR4 with thickness 0.16 cm and dielectric constant 2.2. Where is the upper substrate layer to patch the slot and substrate down to the transmission linefeed. Using the technique of unification that can make optimal matching impedance. For design of microstripantenna is done by using two method that is simulation and measurement. The simulation method is an application of design and method with HFSS software version 13 application. From the simulation result obtained antenna parameters such as bandwidth of return loss below -10 dB obtained single band return loss, and for VSWR 1 to 2 obtained the lowest simulation result is 1.1 achieved at a frequency of 9.8 GHz. The resulting polarization is lobe. From the measurement results obtained values on the return loss graph with operating bandwidth (return loss <-10 dB) is a band with the characteristics of millimeters wave (> 1 GHz) on the band operating from 3.5 to 9.6 GHz (6.1 GHz). Keywords :Microstrip Antenna, coupling proximity, Patch Dual U? Slot, multiwide-band 5G

Page 7 of 19 | Total Record : 182


Filter by Year

2012 2023


Filter By Issues
All Issue Vol. 11 No. 2 (2023): JREC (Journal of Electrical and Electronics) Vol. 11 No. 1 (2023): JREC (Journal of Electrical and Electronics) Vol. 10 No. 2 (2022): JREC (Journal of Electrical and Electronics) Vol 10 No 2 (2022): JREC (Journal of Electrical and Electronics) Vol. 10 No. 1 (2022): JREC (Journal of Electrical and Electronics) Vol 10 No 1 (2022): JREC (Journal of Electrical and Electronics) Vol. 9 No. 2 (2021): JREC (Journal of Electrical and Electronics) Vol 9 No 2 (2021): JREC (Journal of Electrical and Electronics) Vol 9 No 1 (2021): JREC (Journal of Electrical and Electronics) Vol 8 No 2 (2020): JREC (Journal of Electrical and Electronics) Vol 8 No 1 (2020): JREC (Journal of Electrical and Electronics) Vol 7 No 2 (2019): JREC (Journal of Electrical and Electronics) Vol 7 No 1 (2019): JREC (Journal of Electrical and Electronics) Vol 6 No 2 (2018): JREC (Journal of Electrical and Electronics) Vol 6 No 1 (2018): JREC (Journal of Electrical and Electronics) Vol 5 No 2 (2017): JREC (Journal of Electrical and Electronics) Vol 5 No 1 (2017): JREC (Journal of Electrical and Electronics) Vol 4 No 2 (2016): JREC (Journal of Electrical and Electronics) Vol 4 No 1 (2016): JREC (Journal of Electrical and Electronics) Vol 3, No 2 (2015): Journal of Electrical and Electronic Vol 3, No 1 (2015): JREC (Journal of Electrical and electronics) Vol 2, No 2 (2014): JREC (Journal of Electrical and electronics) Vol 2, No 1 (2014): JREC (Journal of Electrical and electronics) Vol 1, No 3 (2013): JREC (Jurnal Of Electrical and Electronics Vol 1 No 3 (2013): JREC (Journal of Electrical and Electronics) Vol 1, No 2 (2013): JREC (Journal of Electrical and Electronics) Vol 1 No 2 (2013): JREC (Journal of Electrical and Electronics) Vol 1, No 1 (2012): JREC Vol 1 No 1 (2012): JREC (Journal of Electrical and Electronics) Vol 1, No 1 (2012): JREC (Journal of Electrical and electronics) More Issue