Eko Naryono
Department of Chemical Engineering, Politeknik Negeri Malang, Jl. Soekarno Hatta No. 9, Malang 65141, Indonesia

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

Producing Precipitated Calcium Carbonate (PCC) from CO2 Emissions during OFMSW Bio-Drying through Carbonation: A Preliminary Study Eko Naryono; Cucuk Evi Lusiani; Mochammad Agung Indra Iswara; Abdul Chalim; Noor Isnaini Azkiya; Amalia Dwi Ardini Putri; Allivia Retnaning Tyas; Kaliawan Kaliawan
Jurnal Teknik Kimia dan Lingkungan Vol. 10 No. 1 (2026): April 2026
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33795/jtkl.v10i1.9573

Abstract

Capturing CO₂ emissions during the bio-drying process of organic fraction municipal solid waste (OFMSW) presents an alternative approach to reducing CO₂ emissions in municipal solid waste (MSW) management. Absorption using an aqueous solution of Ca(OH)₂ is a viable CO₂ capture technology that produces precipitated calcium carbonate (PCC), a value-added product. The objectives of this study are to assess the impact of bio-drying aeration flow rate and absorption time in the Ca(OH)₂ solution on CO₂ absorption efficiency, the conversion of Ca(OH)₂, and the mass of the PCC product. The absorption process was performed in a semi-continuous bubble reactor with 15 L of 0.019 M Ca(OH)₂ aqueous solution. At bio-drying aeration flow rates of 5.1, 4.6, and 3.9 L/min/kg of waste, with CO₂ concentrations ranging from 1286 to 4395 ppm and temperatures between 23 to 30°C over a bio-drying period of 96 hours, it was observed that higher flow rates resulted in lower conversion rates of Ca(OH)₂ and reduced CO₂ absorption efficiency. The highest recorded conversion rates for Ca(OH)₂ and CO₂ absorption were 97.3% and 16.4%, respectively, yielding a PCC product of 4.8 g/kg of waste at an aeration flow rate of 3.9 L/min/kg waste and an absorption duration of 48 hours. FTIR and SEM analysis confirmed the presence of both calcite and aragonite crystal forms in the PCC product, as well as hydrated CaCO₃.
The Influence of Plastic Waste Types and Ratios on the Characteristics of Alternative Fuels through the Pyrolysis Method Mochammad Agung Indra Iswara; Eko Naryono; Mufid Mufid; Anang Takwanto; Luchis Rubianto; Windi Zamrudy
Jurnal Teknik Kimia dan Lingkungan Vol. 10 No. 2 (2026): October 2026
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33795/jtkl.v10i2.9249

Abstract

The increasing volume of plastic waste highlights the urgent need for efficient and environmentally sustainable treatment methods. Pyrolysis is recognized as a promising thermochemical process for converting plastic waste into alternative liquid fuels. This study evaluates the use of rice husks, corn cobs, and coconut shells as renewable heat sources in the pyrolysis of polypropylene (PP) and polyethylene terephthalate (PET), applying biomass-to-plastic ratios of 1:8, 1:12, and 1:16. Key parameters assessed include reactor temperature, liquid fuel yield, and fuel properties. The results show that coconut shells produced the highest reactor temperatures and the most optimal yields, reaching 11.95% for PP and 2.74% for PET. PP-derived oil demonstrated the best fuel quality, with a calorific value of 12,038.9 cal/g, density of 0.728 g/cm3, and viscosity of 2.33 cSt, corresponding to the gasoline-kerosene fraction. In contrast, PET-derived oil exhibited a calorific value of 11,348.1 cal/g, density of 0.809 g/cm3, and viscosity of 3.47 cSt, aligning with the kerosene-diesel fraction. These findings confirm the potential of integrating biomass combustion with plastic pyrolysis as a viable pathway for producing alternative liquid fuels while promoting the utilization of agricultural residues as renewable energy sources.