Claim Missing Document
Check
Articles

Found 36 Documents
Search

Fuzzy Logic Implementation to Control Temperature and Humidity in a Bread Proofing Machine Aulia Ullah; Oktaf Brillian Kharisma; Imam Santoso
Indonesian Journal of Artificial Intelligence and Data Mining Vol 1, No 2 (2018): September 2018
Publisher : Universitas Islam Negeri Sultan Syarif Kasim Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (941.264 KB) | DOI: 10.24014/ijaidm.v1i2.5664

Abstract

Factors that need to be considered of producing good quality bread are raw materials, balance formulas (recipes) and production processes. The bread dough that cannot proof perfectly has become a problem in the process of bread production. Therefore, the temperature and humidity of the room must be controlled at a certain temperature range. The solution of this problem is proposing a controller that uses Fuzzy logic to control temperature and humidity in the bread examination room. A bread proofing machine is added a controller such as evaporator that it is can controlled the temperatur and humidity automatically. The heat and steam produced are regulated using a Fuzzy logic algorithm embedded in the microcontroller with a predetermined set point of temperature and humidity is 35 oC and 80%. The test is done by determining the percentage error from the temperature and humidity test results, that is when the machine is free of load obtained the percentage error to set points is 0,429 %  and 0,937 %. While the engine is loaded. It gives the results are 0,024 % and 0,015%. The results of this test prove that controlling temperature and humidity in a bread proofing machine using Fuzzy logic can provide good results compared to conventional controllers. as a result, the bread mixture can expand uniformly.
Rancang Bangun Power Backup System Pada Pengendali Nanoparticle Sampler (Studi Kasus Nano Sampler EA-Nanonet - UIN Suska Riau) Aulia Ullah; R. Reski Eka Putra
Seminar Nasional Teknologi Informasi Komunikasi dan Industri 2019: SNTIKI 11
Publisher : UIN Sultan Syarif Kasim Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (614.506 KB)

Abstract

Untuk memenuhi informasi polutan partikel padat di udara, UIN Suska Riau sebagai member EA-Nanonet melakukan pengukuran kualitas udara menggunakan nanoparticle sampler. Permasalahannya adalah ketika proses pengambilan data, sistem harus menyala secara kontiniu. Sehingga diperlukan catu daya cadangan untuk menyuplai sistem, dan ketika proses pergantian tidak  boleh terjadi "drop tegangan".  Tulisan ini mengusulkan power supply hibrida dengan mengombinasikan listrik PLN sebagai sistem penyuplai daya utama dan PLTS sebagai daya cadangan. Sistem terdiri dari modul surya 20Wp, SCC 10A, baterai 7Ah, adaptor 9V, IC regulator tegangan 9V. Sebagai alat penukar jaringan, digunakan rele DPDT 250VAC 10A, dan Elco 18800µf 25V ditambahkan untuk mengurangi penurunan tegangan secara tiba-tiba ketika terjadi pergantian sumber catu daya. Hasil pengukuran, konsumsi energi harian perangkat sebesar 33,285 Wh. Berdasarkan pengujian, sistem penyuplai daya cadangan untuk alat pengendali nanoparticle sampler yang dibuat berhasil mempertahankan suplai daya. Ketika listrik PLN padam, berhasil berpindah ke catu daya cadangan sistem PLTS dengan cepat tanpa mengalami jatuh tegangan.
Pengendalian Interaksi Manusia Dan Robot Lengan Berbasis ARDUlNO'UNOR3 Aulia Ullah
Seminar Nasional Teknologi Informasi Komunikasi dan Industri 2018: SNTIKI 10
Publisher : UIN Sultan Syarif Kasim Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (998.656 KB)

Abstract

Setiap jenis pekerjaan mempunyai risiko kecelakaan kerja masing-masing. Kecelakaan kerja bisa disebabkan oleh faktor lingkungan kerja maupun kelalaian pekerja. Kecelakaan kerja dapat menimbulkan kerugian materi dan juga kerugian fisik. Oleh karena itu diperlukan sebuah sistem ataupun alat yang dapat menggantikan pekerjaan manusia yang dianggap berbahaya dan berisiko. Sistem robotik sangat cocok untuk menggantikan pekerjaan manusia yang dianggap berbahaya dan berisiko. Sistem robotik manipulator yang ditambahkan sensor gerak Accelerometer dan Flex serta menggunakan pengaturan putar dari Potensiometer dapat mengendalikan Robot lengan sesuai dengan gerakkan yang diinginkan. Sensor Accelerometer, sensor Flex, dan Potensiometer menggerakkan motor servo pada Robot lengan. Pencengkeram yang digunakan pada Robot lengan dapat mencengkeram benda berukuran 0,1 cm hingga 3 cm dengan menggunakan tegangan keluaran pada Flex sebesar 1,16 V untuk lebar cengkeraman O cm dan 2,51 V untuk lebar cengkeraman 3 cm. Accelerometer bekerja pada sumbu x dan y dengan memberi sudut kemiringan 00- 900 tiap masing-masin sumbu dan menghasilkan nilai skala sensitivitas yang dikirim ke Arduino untuk diolah menjadi skala pada motor servo. Potensiometer memberikan level sinyal berdasarkan sudut putaran dan menggerakkan servo sesuai dengan sudut putaran Potensiometer.Kata kunci : Kecelakaan kerja, Robot Servo
PENGEMBANGAN SISTEM AKUISISI DATA RADIASI MATAHARI MENGGUNAKAN PHYRANOMETER MEMANFAATKAN SENSOR PHOTOVOLTAIC Aulia Ullah; Edy Syahputra
Seminar Nasional Teknologi Informasi Komunikasi dan Industri 2017: SNTIKI 9
Publisher : UIN Sultan Syarif Kasim Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1192.174 KB)

Abstract

Perancangan pembangkit listrik tenaga surya di suatu lokasi sangat dipengaruhi oleh intensitas radiasi matahari, sebab variabel tersebut memiliki pengaruh terhadap daya keluaran yang dihasilkan panel surya. Data ini umumnya bisa didapatkan dari lembaga pemerintah seperti BMKG atau NASA, namun data tersebut hanya tersedia untuk wilayah tertentu saja. Pengukuran radiasi matahari secara langsung perlu dilakukan untuk memenuhi kebutuhan data yang tidak tersedia. Alat yang digunakan untuk mengukur radiasi matahari umumnya menggunakan pyranometer, namun pyranometer konvensional harganya relatif mahal. Pyranometer dapat dibuat lebih murah dengan cara menggunakan sensor photovoltaic sebagai pengganti sensor radiasi matahari. Agar Proses pengukuran lebih mudah dan portabel, pengiriman data dari sensor dilakukan secara wireless, dan untuk memudahkan mengolah data tersebut lebih lanjut dilakukan proses akusisi data. Dari proses pengujian didapatkan, akurasi sensor photovoltaic pyranometer memiliki error 14,13 % dengan error pengiriman data sebesar 0,43 %. Proses akusisi data berjalan dengan baik, sudah dapat menampilkan grafik dan menampilkan data lampau.
Implementasi Penghematan Penerangan Jalan Umum Tenaga Surya (PJUTS) di Jalan Kolektor Primer Aulia Ullah; Ricard Misco Oktaviandra
Seminar Nasional Teknologi Informasi Komunikasi dan Industri 2020: SNTIKI 12
Publisher : UIN Sultan Syarif Kasim Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Penerangan Jalan Umum (PJU) digunakan sebagai sarana penerangan jalan raya ketika malam hari. Keberadaan PJU ini, selain mengurangi angka kejahatan, juga mampu mengurangi angka kecelakaan. Jumlah PJU yang terpasang di beberapa ruas jalan utama membebani tagihan listrik pemerintah daerah, perlu upaya penghematan. Penelitian ini mengusulkan Penerangan Jalan Umum Tenaga Surya (PJUTS), sebagai solusi mengurangi konsumsi energi listrik dari PLN. Untuk mengurangi penggunaan beban lampu yang tidak diperlukan, PJUTS ini dilengkapi dengan sistem penghematan listrik dengan cara meredupkan nyala lampu jika tidak diperlukan. PJUTS ini terdiri dari Panel Surya, Solar Charger Controller, Aki, dan dilengkapi sensor PIR, potensiometer, relai sebagai komponen penghemat daya. Untuk menguji performa sistem, PJUTS ini di implementasikan di jalan lintas Pemda Perawang. Dari hasil pengujian didapatkan sistem yang digunakan terbukti mampu menyalakan lampu PJUTS mulai dari petang hingga fajar tanpa ada kendala. Pengujian intensitas penerangan pun telah memenuhi standar SNI 7391:2008. Mekanisme penghematan otomatis pada PJUTS ini mampu menghemat penggunaan energi hingga 36,9 % dibandingkan PJUTS konvensional.
Akuisisi Data Pengukuran Kecepatan Udara Menggunakan Perangkat MyDAQ dan LabVIEW Aulia Ullah
Seminar Nasional Teknologi Informasi Komunikasi dan Industri 2018: SNTIKI 10
Publisher : UIN Sultan Syarif Kasim Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (476.203 KB)

Abstract

Udara memiliki banyak manfaat bagi manusia. Ketika udara bergerak, memiliki banyak sifat yang bisa manfaatkan berbagai aplikasi. Misalkan energi kinetiknya bisa untuk memutar turbin menghasilkan energi listrik. sayangnya proses pengukuran kecepatan udara umumnya masih manual, kalau pun ada yang pengukuran secara otomatis, belum bisa diolah langsung untuk keperluan analisis lebih lanjut. Untuk itu perlu dilakukan proses akuisisi data hasil pengukuran menjadi grafik dan tersimpan dalam bentuk database sebagai data historis. Penelitian ini bertujuan untuk membuat yang mengukur kecepatan udara lalu diakuisisi menggunakan MyDAQ (My Data Acquisition). Perangkat MyDAQ digunakan karena mampu sebagai antar muka dari sensor ke PC (PersonalComputer). Data digital yang berasal dari sensor optokopler dan sensor fotodioda diterima oleh MyDAQ, selanjutnya dikirim ke PC untuk diproses menggunakan Labview. Perangkat lunak LabVIEW digunakan untuk proses akuisisi data. Dari hasil pengujian, sistem ini mempunyai akurasi rata-rata 83 %, presisi rata-rata 83 %, kesalahan rata-rata 16,9 %. Sistem berhasil dengan baik melakukan proses akuisisi data, terbukti hasil pengukuran dapat ditampilkan dengan grafik dan data pengukuran berhasil tersimpan dengan baik di dalam database. Kata kunci: Akuisisi data, pengukuran, kecepatan udara, MyDAQ, LabVIEW
Alat Monitoring dan Notifikasi Penggunaan Daya Listrik Rumah Tangga Berbasis Internet Of Things Menggunakan Blynk 2.0 Arif Sandira; Jufrizel; Putut Son Maria; Aulia Ullah
Jurnal Komputer Terapan Vol. 8 No. 2 (2022): Jurnal Komputer Terapan
Publisher : Politeknik Caltex Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35143/jkt.v8i2.5761

Abstract

Every year the number of electricity consumers continues to increase, but knowledge about electricity is still poorly understood, especially for consumers in the household aspect even though digital kWh meters have been applied, this causes the use of electrical energy to be less efficient. This study aims to create a monitoring tool for the use of electric power as well as a notification so that consumers can save electricity costs. The method used is research and development to improve existing products by testing their effectiveness. This tool uses the PZEM-004T module as a current and voltage reader sensor, and Blynk 2.0 as an internet of things platform. The test results show the tool can read the voltage with a difference of 0.7V and the current with a difference of 0.1433A. The tool can monitor electricity, and there are notifications on tools and smartphones in the form of warnings for 500 Watt usage, increasing the number of usages of Rp. 5000, and Offline conditions. The experiment of implementing the tool for 6 days, consumers were able to save electricity usage as much as 0.51kWh or equivalent to Rp.781.01 compared to without the tool.
Rancang Bangun Keamanan Kotak Amal dengan Akses Fingerprint Menggunakan ESP32-Cam dan Telegram Berbasis IOT Diky Hermawan; Jufrizel Jufrizel; Aulia Ullah; Ahmad Faizal
JURNAL MEDIA INFORMATIKA BUDIDARMA Vol 7, No 3 (2023): Juli 2023
Publisher : Universitas Budi Darma

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30865/mib.v7i3.6252

Abstract

The charity box is one of the objects that is often the center of attention by thieves, the security of the charity box in current technological developments can be further developed, the creation of a charity box security tool with Fingerprint access using an IOT-based ESP32-cam is one of the developments that aims to improve security in charity box and reduce the rate of theft that occurs. The tool is made using Arduino UNO as the main microcontroller that processes data in this design and ESP32-cam as the recipient of commands from Arduino Uno and Telegram after which it sends data in the form of notifications in the form of photos and sentences describing the images that have been sent. Using 2 sensor inputs, namely the Fingerprint sensor to open the lid of the charity box door, if the fingerprint is registered, it sends a command to the Solenoid to open the charity box door, whereas when the fingerprint is not registered, the Solenoid will not open after that, ESP32-cam gets an order to capture the photo. sent to the telegram application and the Limit Switch sensor functions to detect the state of the charity box door when there is a forced opening that occurs at the door it will send data to Arduino UNO that there is a threat then the buzzer will sound. After testing the results obtained have a success rate of 100%, the ESP32-cam can receive orders to take pictures properly if one of the sensors used is active and can send data in the form of photos to the telegram application properly then the sensor used also works well well, the buzzer will sound when a forced opening is detected by the Limit Switch sensor. In this research it is hoped that it can improve the security of the charity box by capturing photos through the applied ESP32-Cam.
Kunci Kelas Terjadwal Teknik Elektro UIN SUSKA Riau Berbasis RFID dan IoT Maria, Putut; Akbar, Farhandhika; Ullah, Aulia; Zarory, Hilman
Jurnal Sistem Cerdas Vol. 6 No. 1 (2023)
Publisher : APIC

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37396/jsc.v6i1.282

Abstract

Currently, the Electrical Engineering classroom at Sultan Syarif Kasim Riau State Islamic University still uses conventional key. The use of conventional key in the classroom is considered impractical in it use, when there is no schedule the door is left open which causes chairs to move rooms and the use of classrooms is not according to schedule because of schedule changes occurred during the first to third week of lectures. The purpose of this research is to create a classroom security system using an automatic door lock based on the lecture schedule. The tool has two accesses by RFID tags and telegram. RFID tags can be used when the device is not connected to the internet and for emergency access. Telegram is used as a chat-based IoT device control to access the door and input the classroom schedule. The research resulted in a device for controlling classroom door locks that can only be accessed and opened according to the lecture schedule. Door access using an RFID card provides a response time in the range of 0.99 to 1.99 seconds and if using a message via telegram bot, the response time is in the range of 1.97 to 2.62 seconds.
Design and Implementation of Continuous Settling Tank (CST) Temperature Monitoring System and Waste Pond Level in a Palm Oil Mills Ulhaq, Muhammad Dafa; Ullah, Aulia; Mansyurdin, Muharpi; Zarory, Hilman; Faizal, Ahmad
Jurnal Sistem Cerdas Vol. 7 No. 1 (2024)
Publisher : APIC

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37396/jsc.v7i1.360

Abstract

Improving time efficiency and reducing work risks are crucial in palm oil mill operations. Two vital factors in palm oil mill operations are CST temperature and effluent pond level. Both of these factors have a significant impact on mill efficiency. Extreme temperatures, either too high or too low, can disrupt the settling and separation process of water, oil and sludge. In addition, overflowing effluent pond levels are often missed by technicians, so checking must be done manually. This research aims to develop a monitoring system that can monitor the temperature of the CST in safe conditions and measure the level of the waste pond in real-time by utilizing Internet of Things (IoT) technology. This control system relies on components such as the NodeMCU ESP8266 microcontroller, DS18B20 temperature sensor, and HC-SR04 proximity sensor. The method used is the design and manufacture of a prototype monitoring system. Field test results show that this system is able to make comparisons with manual measurement methods. In testing the CST temperature sensor and the waste pool level sensor, the accuracy rate reached 100%. The temperature was successfully monitored with a safe limit of 89°C, while the waste pool level was monitored through the monitoring website. This Internet of Things-based monitoring system has shown significant potential in improving the efficiency and safety of palm oil mill operations, and enables mill operators to effectively conduct remote real-time monitoring.