Claim Missing Document
Check
Articles

Found 5 Documents
Search

Simulation and optimization of coupling reaction of methanol synthesis and isopropyl alcohol dehydrogenation Jenny Rizkiana; Yogi Wibisono Budhi; Azis Trianto
Jurnal Teknik Kimia Indonesia Vol 10, No 3 (2011)
Publisher : ASOSIASI PENDIDIKAN TINGGI TEKNIK KIMIA INDONESIA (APTEKIM)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.5614/jtki.2011.10.3.3

Abstract

A study on simulation and optimization of coupling reaction between methanol synthesis and isopropyl alcohol (IPA) dehydrogenation was performed. The analysis is carried out theoretically to obtain the optimum operation conditions which give the best performance. The reactions are just interacting thermally. In this study, both reactions are held catalytically in a heat-exchanger type reactor. As a high pressure reaction, methanol synthesis is placed in the inner side of reactor tube while dehydrogenation of IPA is in the opposite. Tube wall acts as a heat transfer media. The reactor is modeled by a steady state heterogeneous equation for a fixed bed reactor. Optimization is done in order to find the optimum value of operation conditions, those are the inlet temperature of both side of reactor and the molar feed flow ratio between the exothermic side and the endothermic side. Sum of weighted reaction conversion is considered to be the objective function that is maximized. The simulation result shows that coupled reactor makes the reaction conversion higher than a conventional adiabatic reactor and the optimum operation conditions give the maximum value of the conversion. This study presents a theoretical proof that coupling reaction is feasible. Keywords: coupling reaction, IPA dehydrogenation, methanol synthesis, optimization, simulated annealingAbstrak Telaah mengenai simulasi dan optimisasi reaksi perangkaian (coupling reaction) antara sintesis metanol dengan dehidrogenasi isopropil alkohol (IPA) telah dilakukan. Analisis dilaksanakan secara teoretik guna mendapatkan kondisi optimum yang akan memberikan hasil terbaik. Pada penelitian ini, kedua reaksi dilaksanakan secara katalitik dalam reaktor bertipe buluh-cangkang. Karena bertekanan tinggi, sintesis metanol ditempatkan pada sisi buluh, sedangkan dehidrogenasi IPA ditempatkan pada sisi cangkang. Dinding buluh berperan sebagai media perpindahan panas. Reaktor dimodelkan dengan reaktor heterogen tunak unggun tetap. Optimisasi dilakukan dalam rangka mendapatkan nilai optimum dari kondisi operasi yang mencakup temperatur inlet sisi eksotermik dan endotermik serta rasio umpan molarnya. Jumlah total konversi reaksi terbobotkan dipilih sebagai nilai objectif yang akan dioptimumkan. Hasil simulasi menunjukkan bahwa reaktor perangkaian termal mampu meningkatkan konversi reaksi jika dibandingkan dengan reaktor adiabatik dan pada kondisi operasi yang optimum diperoleh konversi maksimal. Penelitian ini menunjukkan bahwa reaksi perangkaian layak untuk dilaksanakan.Kata kunci: reaksi perangkaian, dehidrogenasi IPA, sintesis methanol, optimisasi, simulated annealing
Simulasi produksi hidrogen melalui CO2 methane reforming pada reaktor membran Azis Trianto; Ira Santrina J C; Susilo Yuwono
Jurnal Teknik Kimia Indonesia Vol 6, No 3 (2007)
Publisher : ASOSIASI PENDIDIKAN TINGGI TEKNIK KIMIA INDONESIA (APTEKIM)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.5614/jtki.2007.6.3.2

Abstract

Hydrogen is a promising alternative fuel to establish environmentally friendly energy generation system. One of the methods for producing hydrogen is C02 methane reforming (CMR) process. Despite producing H2, this process also consumes CO2 enabling it to be used as a scheme for mitigating CO2. Conventionally, the hydrogen production via CMR is conducted in a fixed bed reactor. However low conversion is usually found in this kind of reactor. To increase conversion, a membrane reactor can be used. Two types of membrane may be employed to conduct this reaction, i.e. prorous  vycor and nanosil membrane  reactor.  This study  evaluated the  performances  of CMR con 1ucted in membrane ractors andfixed-bed reactor. The results show that the conversion obtained in nanosil membrane reactor is higher than those obtained in porous vycor membrane reactor and fixed-bed reactor. With the change in reactant flowrate, it is obtained that the conversions in membrane reactors are more stable than those infixed bed reactors.Keywords: Hydrogen Production, Membrane Reactor, Methane Reforming AbstrakHidrogen merupakan bahan bakar alternatif yang sangat menjanjikan untuk sistem pembangkitan energi yang lebih ramah lingkungan. Salah satu rute produksi hidrogen adalah melalui reformasi metana dengan karbondioksida (C02 Methane Reforming/CMR). Saat ini telah dikembangkan proses CMR menggunakan membran yang mampu meningkatkan laju produksi H2• Pada makalah ini dikaji dua tipe reaktor membran untuk maksud peningkatan produksi hidrogen tersebut, yakni reaktor membran dengan basis membran porous vycor dan nanosil. Sebagai pembanding, dilakukanjuga evaluasi unjuk kerja reaksi CMRpada reaktorfzxe-bed. Hasil kajian ini menurljukkan bahwa reaktor nanosil danporous vycor mampu memberikan konversiyang lebih besar dibanding reaktor fixed-bed. Lebihjauh, reaktor membran dengan nanosil membran mampu memberikan laju produksi hidrogen yang lebih tinggi dibanding reaktor membran dengan membran porous vycor. Lebih jauh, pada perubahan laju molar reaktan, reaktor membran menurijukkan stabilitas yang lebih baik dibanding reaktor fixed-bed.Kata Kunci: Produksi Hidrogen, Reaktor Membran, Reformasi Metana
TINJAUAN ASPEK KESELAMATAN UJI STATIK ROKET DENGAN PROPELAN KEROSEN–ASAM NITRAT TERHADAP MANUSIA DAN LINGKUNGAN Arif Nur Hakim; Azis Trianto; Pramujo Widiatmoko; Risky Darmawan
Jurnal Teknologi Dirgantara Vol 6, No.2 Desember (2008)
Publisher : National Institute of Aeronautics and Space - LAPAN

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Roket propelan cair memiliki beberapa kelebihan bila dibandingkan dengan roket propelan padat. Jumlah dan perbandingan bahan bakar terhadap oksidator dapat diatur untuk menghasilkan gaya dorong yang diinginkan. Salah satu propelan yang digunakan saat ini adalah pasangan kerosen dan asam nitrat. Namun, penggunaan propelan ini memunculkan masalah akibat karakter propelannya. Asam nitrat adalah cairan yang sangat korosif dan dapat menyebabkan efek yang serius terhadap tubuh manusia. Tinjauan terhadap keselamatan dalam uji statik roket cair telah dilakukan. Pada uji statik, kerosen dan asam nitrat akan diinjeksi ke dalam ruang bakar dan bereaksi sehingga menghasilkan gas bertekanan dan bertemperatur tinggi yang kemudian disemburkan melalui nosel untuk menghasilkan gaya dorong. Dari hasil kajian, daerah pengujian dibagi menjadi 5 zona. Zona 1, daerah yang paling berbahaya berjarak 0 – 3 m, dan zona 2, 3 – 40 m, adalah daerah yang masih dipengaruhi oleh gas-gas berbahaya. Pengamatan langsung dapat dilakukan pada jarak 50 m dengan perlindungan bangunan.
Pengukuran konstanta henry toluen dan benzen dalam minyak dan air dengan kolom gelembung S Suhartono; Herri Susanto; Dwiwahju Sasongko; Azis Trianto
Jurnal Teknik Kimia Indonesia Vol 9, No 2 (2010)
Publisher : ASOSIASI PENDIDIKAN TINGGI TEKNIK KIMIA INDONESIA (APTEKIM)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.5614/jtki.2010.9.2.2

Abstract

Determination of Henry’s constant for toluene and benzene in oils and water were carried out in a bubbling bottle with diameter of 3 cm. Air containing toluene vapour or benzene vapour was bubbled through 50 mL absorbing liquid. The gas flow rate was 13.6 mL/min. By measuring the concentration of toluene or benzene in the inlet and outlet gas stream, we were able to calculate their concentrations in absorbing liquid. We found that the value of Henry’s constant of toluene in lubrication oil and palm oil at 30 oC were 155 and 145 respectively (H= CG/CL, with CG in mol/L and CL in mol/L). We also found that the absorption capacities were in the order (from the highest) of: lubrication oil, palm oil, and sunflower oil. Henry’s constant of toluene in water was at about 4 which was much lower than those of oils.Keyword: absorption, Henry’s constant, toluene, benzene, producer gas AbstrakPengukuran konstanta Henry sistem toluen dan benzen dalam minyak dan air dilakukan melalui percobaan absorpsi di dalam sebuah kolom gelembung dengan diameter 3 cm. Minyak sawit, minyak bunga matahari, minyak pelumas dan air digunakan sebagai absorben. Toluen dan benzen dipilih sebagai tar model. Gas model yang tersusun dari udara dan uap toluen atau benzen digelembungkan ke dalam absorben 50 mL. Absorpsi dilakukan pada suhu 30 dan 60 oC dan laju alir gas model 13,6 mL/min. Analisa dilakukan terhadap konsentrasi aliran gas model sebelum dan sesudah absorpsi. Analisa tersebut dilakukan dengan kromatografi gas Shimadzu GC-8APF. Konstanta Henry dihitung sebagai H=CG/CL dan H=P/CL. Nilai 1/H sistem toluen-minyak pelumas dan toluen-minyak sawit pada suhu 30 oC dan laju alir gas 13,6 mL/min berturut-turut adalah 155 dan 145 (untuk CG dalam mol/L dan CL dalam mol/L). Merujuk pada nilai-nilai konstanta Henry hasil percobaan, minyak pelumas dan minyak sawit merupakan cairan penyerap yang paling cocok untuk toluen dan benzen sebagai representasi tar dalam gas hasil gasifikasi. Urutan besarnya kapasitas absorpsi cairan penyerap terhadap toluen dan benzen adalah sebagai berikut (berturut-turut dari yang besar): minyak pelumas, minyak sawit, minyak bunga matahari dan air. Konstanta Henry toluen dalam air berada pada kisaran 4, yang menunjukkan bahwa kapasitas absorpsi toluen dalam air lebih rendah dibandingkan kapasitas absorpsi toluen dalam minyak.Kata Kunci: absorpsi, konstanta Henry, toluen, benzen, gas produser
Propane Dehydrogenation in a Modified Porous Membrane Reactor for Producing Propylene with Chemical and Polymer Grades Azis Trianto; Yazid Bindar; Noezran Noezran
ASEAN Journal of Chemical Engineering Vol 5, No 2 (2005)
Publisher : Department of Chemical Engineering, Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/ajche.50187

Abstract

Propane dehydrogenation is a promising route for producing propylene to replace traditional cracking methods. A membrane reactor offers a possibility to produce not only chemical grade but also polymer grade of propylene. The purpose of the present study is to evaluate the performance of a Modified Porous Membrane Reactor (MPMR) in producing these two propylene grades simultaneously. The study involves evaluations based on thermodynamics and process flow sheeting. The performance of this reactor is compared to that of conventional reactor. At first, the thermodynamics is conducted using minimum Gibb's Energy approach. Then the process flow sheeting evaluation is built using the HYSYS simulator. The effect of inert gas (steam) concentration in both sweep and feed sides is investigated. The thermodynamics study results optimum temperature and inert gas concentration to obtain these two grades of propylene simultaneously. The propylene with polymer grade above 99% is produced from the sweep side outlet. The propylene with chemical grade is produced from the feed side outlet. The simultaneous production of these two grades of propylene has benefit in vanishing propane-propylene splitter. Keywords: Membrane reactor, porous membrane, propane dehydrogenation, propylene production, and process simulation.