Emiliana Kasmudjiastuti
Unknown Affiliation

Published : 21 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 21 Documents
Search

Pengaruh jumlah air terhadap jumlah serapan Cr2O3 pada proses penyamakan krom kulit kambing Emiliana Kasmudjiastuti
Majalah Kulit, Karet, dan Plastik Vol 24, No 1 (2008): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (955.123 KB) | DOI: 10.20543/mkkp.v24i1.321

Abstract

            The objective of the research was to study the effect of number of water of Cr2O3 absorbtion in chrome tanning for goat skin and to reduce utilization of water and chrome waste and to optimize function of Cr2O3. Waste water of pickle were used in variation of 20, 40, 60% respectively and control was also mode as comparation. Twenty pieces of green salted goat skin were grouped and devided into four groups and every five pieces were treated five pieces. The applications parameters of quality were determined including Cr2O3 absorbtion, shrinkage temperature, tensile strength, elongation at break, stitch strength and tear strength. The results showed that the number of Cr2O3 absorb and shrinkage temperature in this research was significantly added water effected on tanning process. The pickle water of 40% performed optimal chrome tanning for goat skin in the amount of 3.13% Cr2O3 absorbtion ; 115.38 0C shrinkage temperature; 216.58 kg/cm2 tensile strength; 43.14% elongation at break; 64.77 kg/cm2 stitch strength; 27.46 kg/cm2 tear strength and all of quality parameters fulfill the requirements of Indonesian National Standard (SNI) 06-117-1989 about Quality and Testing Method Goat Skin Glace. Key words : Goat skin, chrome tanning, shrinkage temperature, tensile strength, elongation at break, stitch strength, tear strength, tear strength ABSTRAK             Penelitian ini bertujuan untuk mempelajari pengaruh jumlah air terhadap serapan Cr2O3  pada proses penyamakan krom kulit kambing serta mengurangi jumlah pemakaian air dalam upaya mengurangi limbah krom dan mengoptimalkan fungsi Cr2O3. Air bekas proses pengasaman (air pikel) ditambahkan dengan jumlah berturut-turut 20,40, dan 60%. Control atau tanpa tambahan air pikel dibuat sebagai pembanding dan kulit yang digunakan sebanyak 20 lembar dibagi dalam 4 kelompok dan masing-masing perlakuan untuk 5 lembar kulit. Parameter mutu kulit yang diamati meliputi Cr2O3 yang terserap dalam kulit, suhu pengkerutan, kekuatan tarik, kemuluran, kekuatan jahit dan kekuatan sobek. Hasil penelitian menunjukan bahwa Cr2O3 yang terserap dalam kulit dan suhu pengkerutan dipengaruhi secara nyata (P≤0,05) oleh air yang ditambahkan pada proses penyamakan. Pemakaian air pikel 40% pada penyamakan krom kulit kambing menunjukan jumlah Cr2O3 yang terserap dalam kulit sebesar 3,13%, suhu pengkerutan 115,380C, kekuatan tarik 216,58 kg/cm2 , kemuluran 43,14%, kekuatan jahit 64,77 kg/cm2, kekuatan sobek 27,46 kg/cm2 dan semua parameter kulit hasil penyamakan memenuhi persyaratan yang ditetapkan dalam SNI 06-1117-1989 tentang mutu dan cara uji kulit glace kambing. Kata kunci : kulit kambing, penyamakan krom, suhu pengkerutan, kekuatan tarik, kemuluran, kekuatan jahit, kekuatan sobek. 
Penelitian korelasi pengaruh cuaca dengan alat weather 0 meter dan dengan cuata langsung udara terbuka terhadap kekuatan bengkuk sol karet cetak Emiliana Kasmudjiastuti
Majalah Kulit, Karet, dan Plastik Vol 9, No 17 (1994): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (926.852 KB) | DOI: 10.20543/mkkp.v9i17.413

Abstract

The aim of this research was to obtain the correlation weathering exposure by Weathering 0 Meter Apparatus (in door weathering test) and directly exposure to the out door weather (out door weather test) on the flexing of moulding rubber sole. Sample used in this research were 216 by weather 0 Meter Apparatus and 147 by directly exposure to the out door weather. Testing for the flexing on rubber and Plastic Physical And Chemist Laboratory, IRDLAI, Yogyakarta, by reference SNI.0778-1989-A. The results of physical tests were analysed using T test. The Correlation for testing of moulding  rubber sole specimen exposes by Weather 0 Meter (in door) for one hour giving similar change in the out door weather as long as 12,8 hours.   INTISARI Penelitian ini bertujuan untuk mengetahui korelasi pengaruh cuaca dengan alat Weather 0 Meter (in door) dan dengan cuaca langsung udara terbuka (out door) terhadap kekuatan bengkuk sol karet cetak. Materi yang digunakan dalam penelitian ini adalah 216 sampel dengan alat Weather 0 Meter dan 147 sampel dengan cuaca langsung udara terbuka. Pengujian kekuatan bengkuk dilakukan di Laboratorium Fisis dan Khemis barang karet dan Plastik BBKKP Yogyakarta dengan mengacu pada SNI 078-1989-A, Sol Karet Cetak. Analisa hasil uji menggunakan metode T test. Korelasi untuk pengujian cuplikan sol karet cetak yang mendapat perlakuan alat Weather 0 Meter (in door) selama 1 jam memberikan perubahan yang sama pada keretakan cuplikan sol karet cetak dengan cuaca langsung udara terbuka (out door) selama 12,8 jam.
Penggunaan zat warna alam untuk kulit non konvensional Emiliana Kasmudjiastuti
Majalah Kulit, Karet, dan Plastik Vol 22, No 1 (2006): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1195.057 KB) | DOI: 10.20543/mkkp.v22i1.330

Abstract

The objective of this experiment was to apply the natural dyes for non conventional leather with mordant environmental friendly. This research used lizard skins, cobra skins and kakap fish skins from dried preservation; woods extract of secang, tegeran, nangka, mahoni and tinggi; chrome and syntan as tanning agent; alum as mordant and material additives for tanning. The methods of this research were preparation of solution extract, tanning and testing. The principles of dyeing with the natural dyes used natural dyes withoud mixed dyestuffs and mordant environtment friendly. The research results showed that the natural dyes from secang woods, tegeran woods, nangka woods, mahoni woods and tingi bark were acid dyes with pH of 4 – 5 and they could be applied on lizard skins, cobra skins and kakap fish skins. The natural dyes from mahoni woods had superior acid resistance (sulphate acid, formic acid and acetate acid), the value was 4/5 (grey scale) and also they had the dry and wet rub fastness which were better than those of natural dyes from secang, tegeran, nangka, and tinggi.  Keywords : natural dyes, woods extract, non conventional skins.   ABSTRAK Penelitian ini bertujuan untuk mengaplikasikan zat warna alam pada kulit non konvensional dengan mordan yang ramah lingkungan. Bahan yang digunakan dalam penelitian ini meliputi : bahan baku berupa kulit biawak, kulit ular kobra, dan kulit ikan kakap awet kering, bahan pewarna dari ekstrak larutan kayu secang, tegeran, nangka, mahoni dan tingi, bahan penyamak krom dan syntan, alum sebagai mordan serta bahan pembantu untuk penyamakan. Tahapan penelitian meliputi persiapan ekstrak larutan zat warna alam, proses penyamakan kulit dan pengujian. Prinsip proses pewarnaan dengan zat warna alam adalah menggunakan zat wrna alam tanpa kombinasi zat warna sintetis, dengan mordan yang ramah lingkungan. Hasil pengujian menunjukkan bahwa zat warna alam dari kayu secang, tegeran, nangka, mahoni dan tingi merupakan zat warna asam dengan pH 4 – 5 dan dapat diterapkan pada kulit biawak, kulit ular kobra dan kulit ikan kakap. Zat warna dari kayu mahoni unggul dalam ketahanan terhadap asam (sulfat, formiat, dan asetat) dengan nilai 4/5 pada skala abu-abu dan mempunyai ketahanan gosok (kering, basah) paling baik (tidak luntur), dengan nilai 4 – 5 pada skala abu-abu. Kata Kunci : zat warna alam, ekstrak kayu, kulit non konvensional.   
Pengaruh sumber dan konsentrasi garam (Na Cl) pada proses pengasaman (pickling) terhadap mutu kulit domba untuk sarung tangan Emiliana Kasmudjiastuti
Majalah Kulit, Karet, dan Plastik Vol 25, No 1 (2009): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2618.53 KB) | DOI: 10.20543/mkkp.v25i1.228

Abstract

The aim of the research was to determine the effects of source and concentration of salt (NaCl) during the pickling process on the leather quality of sheep skin for glove. The kind of salt and concentration developed during pickling process of sheep skin the purified salt, Australian salt, Wedung Demak salt, Madura salt and control salt, was utilized the various concentration was 4%, 6% and 8%, respectively. The test parameter are chemist, physical and visual test. The sheep leather was products like wet blue leather and crust leather, and then they were subsequently tested for their quality such as water content, ash content and Cr2O3 content for wet blue leather and visual test for crust leather such as condition of leather, color, tear strength and resilient. The wet blue leather was water 44,98%, dust 6,90%, and Cr2O3 3,7%, performed with SNI 06-3538-1994, Standard sheep/goat wet blue leathers. Crust of that leather was bright leather condition about soft, non deflated, flexible, color was average, the tear strength moderately was powerful, the spring was elastic, tensile strength was 156,62 kg/cm2 and elongation at break 42% these quality parameter were comply with regulation standard was SNI 06-4035-1996, Standard the glove leather from sheep/goat leather. Key words : salt (NaCl), pickling, leather quality, sheep. ABSTRAK Tujuan penelitian adalah mempelajari pengaruh penggunaan jenis dan konsentrasi garam pada proses pengasaman terhadap mutu kulit domba (wet blue dan kras) yang dihasilkan. Jenis garam dan konsentrasi yang digunakan dalam proses pengasaman bervariasi yaitu dengan garam Purifikasi, Australia, Wedung Demak, Madura dan Kontrol (garam di pasaran) dan konsentrasi berturut-turut 4,6 dan 8%. Parameter uji mutu kulit domba meliputi uji kimia, fisik dan organoleptis. Kulit wet blue diuji kadar air, kadar abu dan kadar Cr2O3. Kulit kras diuji secara organoleptis yang meliputi keadaan kulit, warna kulit, ketahanan sobek dan kelentingan serta uji fisis (kekuatan tarik dan kemuluran). Hasil uji menunjukkan bahwa kulit wet blue dan kulit kras yang memiliki mutu terbaik adalah menggunakan garam Wedung Demak dengan konsentrasi 8%, memberikan hasil kulit wet blue dengan kadar air 44,98%, kadar abu 6,90% dan kadar Cr2O3 3,70%,memenuhi persyaratan mutu yang ditetapkan dalam SNI 06-3538-1994 tentang Kulit Wet Blue Domba/Kambing. Kulit kras yang dihasilkan mempunyai kenampakan visual seperti keadaan kulit lunak, tak gembos, lemas, warna cukup rata, ketahanan sobek kuat, kelentingan elastic, dan kekuatan fisik seperti kekuatan tarik 156,62 kg/cm2, kemuluran 42% dan memenuhi persyaratan SNI 06-4035-1996 Kulit Sarung Tangan dari Kulit Domba/Kambing.Kata kunci : garam (NaCl), pengasaman, mutu kulit, domba.
Penelitian penggunaan minarex sebagai bahan pelunak dalam pembuatan kompon karet sol karet cetak Emiliana Kasmudjiastuti; Murwati Murwati
Majalah Kulit, Karet, dan Plastik Vol 10, No 20 (1995): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (792.107 KB) | DOI: 10.20543/mkkp.v10i20.446

Abstract

The objective of this research is to use Minarex oil as a softener in making rubber sole compound and to know the optimal of formulation. The research applied Minarex type 3 with four kinds of A, B, C, D and with variation 5 parts, 6 parts, and 7 parts. Data analysed using Statistic Method with Compleetely Randomized Design and Split Plot Design. The result of this study showed that all kind of Minarex oils could be used to softener in making rubber sole compound and fullfilled the spesification of SNI 0778-89-A, "Sol Karet Cetak". The optimal of formulation to Minarex type 3 was Minarex C with application 7 parts.  Penelitian ini bertujuan untuk memanfaatkan Minarex sebagai bahan untuk pelunak dalam pembuatan kompon karet untuk sol karet cetak dan untuk mengetahui foemula yang optimal. DAlam penelitian ini digunakan Minarex tipe 3 dengan jenis A, B, C, D dan dengan variasi jumlah 5 bagian, 6 bagian, dan 7 bagian. Analisa data menggunakan Metode Statistik Compleetely Randomized Design (CRD) dan Split Plot Design. Hasil penelitian menunjukkan bahwa semua jenis Minarex A, B, C, dan D dapat digunakan sebagai bahan pelunakpada pembuatan kompon sol karet cetak dan semua kombinasi memenuhi persyaratan SNI 0778-89-A, "Sol Karet Cetak". Formula optimal dicapai oleh Minarex C tipe 3 dengan variasi jumlah Minarex 7 bagian.
Penentuan tipe minarex a yang optimum pada pembuatan kompon karet untuk sol karet cetak ditinjau dari sifat fisisnya Agustin Suraswati; Emiliana Kasmudjiastuti; Murwati Murwati
Majalah Kulit, Karet, dan Plastik Vol 12, No 22 (1996): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (810.608 KB) | DOI: 10.20543/mkkp.v12i22.344

Abstract

The objective of this research is to know type optimum of Minarex A to make rubber compound for rubber sole to orientate of physical characteristic. All compound with Minarex A type 2 and type 3 fulfil SNI. 0778 – 89 A,  rubber sole class A. the rubber compound with Minarex A type 3 for physical testing is tensile strength, elongation strength, hardness, permanent elongation 50% and abrasion resistance, better from Minarex A type 2. Exactly the rubber compound with Minarex A type 2 for physical testing is tearing resistance and specific gravity better from Minarex type 3. The optimal condition is reached by using Minarex A type 3.    INTISARI  Penelitian ini bertujuan untuk mengetahui tipe Minarex A yang optimum pada pembuatan kompon karet untuk sol karet cetak ditinjau dari sifat fisisnya. Semua kompon dengan menggunakan Minarex A tipe 2 maupun tipe 3 memenuhi persyaratan SNI. 0778 – 89 A, Sol Karet Cetak Kelas A. kompon karet dengan menggunakan Minarex A tipe 3 sifat tegangan putus, perpanjangan putus, kekerasan, perpanjangan tetap 50% dan ketahanan kikis lebih baik dari kompon karet dengan menggunakan Minarex A tipe 2. Sedang kompon karet dengan menggunakan Minarex A tipe 2 uji fisis ketahanan sobek dan bobot jenis lebih baik dari kompon karet dengan menggunakan Minarex A tipe 3. Keadaan optimal dicapai pada penggunaan Minarex A tipe 3. 
Pengaruh filler PCC (precipitated calcium carbonate) terhadap sifat mekanik, elektrik, termal dan morfologi dari komposit HDPE/PCC Emiliana Kasmudjiastuti; Arum Yuniari
Majalah Kulit, Karet, dan Plastik Vol 28, No 1 (2012): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (538.533 KB) | DOI: 10.20543/mkkp.v28i1.203

Abstract

ABSTRACTThe purpose of this research was to know the effect of precipitated calcium carbonate(PCC) on morphology and quality of the HDPE g-MAH with PCC as filler. The process of HDPEg-MAH /PCC composites with a rheomix 3000 Haake at 180 º C and 50 rpm of rotor speed for 10minutes. The composition of HDPE and additives are set constant, and PCC content was varied10, 15 , 20, 30,40 and 50 phr (per hundred resin). The results of scanning electron microscopyshowed that composite HDPE-g-MAH dan 30 phr of PCC was compatibel. Analysis functionalgroup on composites with Fourier Transform Infra Red (FTIR) indicated wave band on 3449,61cm-1, 2921 cm-1, 1707,21 cm-1, 1485 cm-1 dan 722,03 cm-1. The test results of the electricalproperties (insulation resistance : ≥ 4 MΩ and electric resistance : no holed), and thermalproperties (sparks : no flame and tissue not burned) indicate that all of the composite HDPE-g-MAH/PCC fullfill SNI 04-6504-2001, except resistance to heat.Keywords: HDPE, PCC, maleic anhidride, electrical reistance, thermal resisitanceABSTRAKTujuan penelitian ini adalah untuk mengetahui pengaruh penggunaan filler PrecipitatedCalcium Carbonat (PCC) terhadap morfologi, sifat mekanik, termal dan elektrik kompositHDPE-g-MAH dengan filler PCC. Pembuatan komposit HDPE-g-MAH dengan filler PCCmenggunakan mesin Rheomix 3000 Haake dengan suhu 180oC, selama 10 menit dan kecepatan50 rpm. Komposisi HDPE dan bahan aditif dibuat tetap, dan kandungan PCC divariasi 0; 10 ;20 ; 30; 40 dan 50 phr (per hundred resin). Morfologi komposit diamati dengan ScanningElectron Microscope (SEM) dengan metode secondary electron image perbesaran 2000 X dankarakterisasi gugus fungsi pada komposit dengan menggunakan Fourier Transform Infra Red(FTIR). Hasil pengamatan morfologi SEM memperlihatkan bahwa permukaan komposit HDPEg-MAH dan PCC 30 phr adalah kompatibel dan hasil uji FTIR terlihat adanya puncak serapanpada panjang gelombang 3449,61 cm-1, 2921 cm-1, 1707,21 cm-1, 1485 cm-1 dan 722,03 cm-1. Darihasil uji mekanikal komposit HDPE-g-MAH berisi filler PCC 30 phr mempunyai densitas 1,18gr/cm3, kekuatan tarik 254,22 kg/cm2, perpanjangan putus 20%, kekerasan 96,6 shore D danketahanan pukul takik 25 kJ/m2. Hasil uji sifat elektrikal (resistansi isolasi : ≥ 4 MΩ dan kuatlistrik: tidak tembus) dan uji thermal (percikan api: tidak ada api dan tisu tidak terbakar)menunjukkan bahwa semua komposit HDPE-g-MAH dengan filler PCC memenuhi SNI 04-6504-2001, kecuali untuk ketahanan panas (uji sifat thermal).Kata kunci: HDPE, PCC, maleat anhidrat, sifat elektrikal, sifat thermal
Kulit ikan kakap tersamak: Exotic dan prospektif Emiliana Kasmudjiastuti
Majalah Kulit, Karet, dan Plastik Vol 21, No 1 (2005): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (525.766 KB) | DOI: 10.20543/mkkp.v21i1.317

Abstract

Kakap fish skins are waste products of fillet industry. Up to now they have been wasted, of course accumulatively will cause environmental pollution. They are classified as the type of non conventional leather and exotic ones for the reasons of having special, beautiful, unique, typical, and attractive grain. Kakap fish skin have relatively small dimentions, there fore the tanning process can be done by home industry because simple equipments are possible to be used to process the fish skins into leather. In addition, Kakap fish leather have physical property of good tensile strength that may be used as material for leather goods. Although small however the exotic leather of kakap fish skins are prospective to be developed as material to manufacture exclusive leather goods, especially for niche markets. They also can be used as an alternative to substitute conventional leather. Keywords : kakap fish, waste, leather goods, exotic.    ABSTRAK Kulit ikan kakap merupaan limbah dari industry fillet ikan, sementara ini hanya dibuang saja, sehingga makin menumpuk dn dapat menyebabkan pencemaran lingkungan. Kulit ikan kakap merupakan jenis kulit non konvensional dan dapat pula digolongkan sebagai kulit exotic karena memiliki rajah yang khas, indah, dan menarik. Kulit ikan kakap memiliki ukuran yang relatif kecil sehingga dalam proses penyamakannya cukup menggunakan peralatan yang sederhana dan dapat dikerjakan oleh industri rumah tangga. Disamping itu kulit, kulit ikan kakap yang exotic walaupun ukurannya kecil, prospektif untuk dikembangkan sebagai bahan baku untuk pembuatan barang-barang kulit yang eksklusif terutama untuk pasar khusus dan dapat digunakan sebagai alternative untuk menggantikan bahan kulit konvensional disaat kurangnya penyediaan kulit konvensional.   Kata Kunci : ikan kakap, limbah, barang kulit, exotic.  
Pengaruh penggunaan bahan pewarna alam dari ekstrak kayu terhadap sifat fisis kulit ikan kakap merah Emiliana Kasmudjiastuti; Widhiati Widhiati
Majalah Kulit, Karet, dan Plastik Vol 18, No 1 (2002): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1830.283 KB) | DOI: 10.20543/mkkp.v18i1.265

Abstract

 The objective of this research is to identify the effect of some natural dye of wood extract to the physical properties (tensile strength, elongation and rub fastness resistance) of kakap (Lutjanidae) fish skin leather. Fifteen pieces of dry preserved kakap fish skin were used in this research, and tanned using syntan and alum. The dyeing process was done using natural dyes of wood extract of Caesalpinia sappan L, Artocarpus heterophyllus, Swietenia mahagoni JACQ, Maclura cochinensis, and Ceriops tagal. The result of research indicated that the kind of applied natural dyes were not affect the physical properties of Kakap fish skins. The fish skins dyed using the such natural dyes was able be utilised as material in leather goods manufacturing. One of the five types of natural dye used in this research, Swietenia mahagoni JACQ wood extract produced the best dyed leather having good tensile strength, elongation/flexibility and the colour fastness. The tensile strength was 213,15 kg/cm2, flexibility 56% and colour fastness with wet white cloth 3/4 (grey scale value) and with dry white cloth 4/5 (grey scale value), respectively. Key words : kakap fish skin, natural dyes, physical properties.
Pengaruh zat warna reaktif terhadap sifat ketahanan luntur warna dan morfologi kulit ikan nila (Tilapia nicotica) untuk garmen Emiliana Kasmudjiastuti
Majalah Kulit, Karet, dan Plastik Vol 27, No 1 (2011): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2676.504 KB) | DOI: 10.20543/mkkp.v27i1.208

Abstract

abstrak