Claim Missing Document
Check
Articles

Found 4 Documents
Search

Design of trainer kit as a fault-finding based on electricity and electronics learning media Muhammad Anwar; Mochamad Bruri Triyono; Ta'ali Ta'ali; Hendra Hidayat; Veva Nellone Syahputeri
Jurnal Pendidikan Vokasi Vol 11, No 2 (2021): June
Publisher : ADGVI & Graduate School of Universitas Negeri Yogyakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21831/jpv.v11i2.43742

Abstract

According to the field of expertise, efforts to strengthen the competence of graduates continue to be pursued, especially through optimizing the learning process. Among these efforts is to use learning media that strengthen the competence of the field of study and about thinking skills. This study aims to produce a trainer kit as a medium for learning basic electricity and electronics based on fault-finding in Basic Electrical and Electronics subjects. The method used is the Richey and Klein Design and Development (DD) method which consists of three stages, including planning (design), production, and evaluation. Experts carried out the assessment of the feasibility of the trainer kit with an instrument in the form of a questionnaire. The results of this study indicate that the trainer kit has a good performance.According to the field of expertise, efforts to strengthen the competence of graduates continue to be pursued, especially through optimizing the learning process. Among these efforts is to use learning media that strengthen the competence of the field of study and about thinking skills. This study aims to produce a trainer kit as a medium for learning basic electricity and electronics based on fault-finding in Basic Electrical and Electronics subjects. The method used is the Richey and Klein Design and Development (DD) method which consists of three stages, including planning (design), production, and evaluation. Experts carried out the assessment of the feasibility of the trainer kit with an instrument in the form of a questionnaire. The results of this study indicate that the trainer kit has a good performance.
Sistem Monitoring dan Kontrol Motor AC 3 Phasa Melalui Inverter dengan Protokol Modbus Menggunakan Visual Basic Berbasis Atmega 2560 Emillia Kartika; Ta'ali Ta'ali; Hastuti Hastuti
JTEV (Jurnal Teknik Elektro dan Vokasional) Vol 6, No 2 (2020): JTEV (Jurnal Teknik Elektro dan Vokasional)
Publisher : Universitas Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (888.706 KB) | DOI: 10.24036/jtev.v6i2.108911

Abstract

A three-phase induction motor is one of the electric machines and is classified as an AC motor that is widely used in the industrial world. The development of control systems in the industry will not be separated from the data communication system. To send data from the field (sensor) to the controller, for communication between controllers, to send data from the controller to the computer, all require data communication. One of the most widely used data communication systems in industrial control systems is the Modbus protocol. Even in the world of education there are also many studies that develop control systems using modbus communication. The speed regulation of three phase induction motor can be done in various ways one of them is by using Variable Speed Drive which functions to adjust the frequency of the source so as to get the desired motor speed (rpm). Communication between VSD, Arduino and PC with the MODBUS protocol is a system built to be able to monitor the performance of a three phase induction motor.
Perancangan Penyortiran Barang Berdasarkan Berat dengan Sistem Pick And Place Berbasis Mikrokontroler Fajrian Ramadhan; Ta'ali Ta'ali
JTEV (Jurnal Teknik Elektro dan Vokasional) Vol 6, No 2 (2020): JTEV (Jurnal Teknik Elektro dan Vokasional)
Publisher : Universitas Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24036/jtev.v6i2.108605

Abstract

Dalam dunia industri diperlukan suatu alat yang mampu beroperasi dengan cepat dan tepat sehingga proses produksi dapat berjalan dengan lebih efektif dan  efisien. Perancangan penyortiran barang berdasarkan berat dengan sistem pick and place berbasis mikrokontroler ini bertujuan agar mampu mengklasifikasikan benda berdasarkan berat agar tertata berdasarkan beratnya masing masing. Mikrokontroler ATmega32(Arduino Uno) berfungsi sebagai pusat kontrol sistem, Sensor load cell sebagai sensor pendeteksi berat benda, Motor DC sebagai penggerak konveyor dan motor servo sebagai penggerak dari sistem pick and place yaitu pergerakan  lengan robot untuk memindahkan benda yang telah terdeteksi beratnya sesuai dengan yang telah ditentukan. Melalui tahapan proses perancangan mekanik dan pemograman sistem dengan menggunakan program dari Arduino IDE, serta hasil dari pengujian dan analisa data didapatkan sistem yang dapat bekerja dengan baik dan kontinu. Meskipun sistem dirancang hanya berupa prototype namun dengan menggunakan perangkat dengan standar industri bisa diaplikasikan dalam mendukung kerja dalam bidang industri yang otomatis dan efisien. 
Analisis Sistem Grounding Di Fakultas Teknik Universitas Negeri Padang Ta'ali Ta'ali; Ali Basrah Pulungan; Hambali Hambali; Shalvadila Shalvadila
JTEV (Jurnal Teknik Elektro dan Vokasional) Vol 7, No 2 (2021): JTEV (Jurnal Teknik Elektro dan Vokasional)
Publisher : Universitas Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (335.623 KB) | DOI: 10.24036/jtev.v7i2.114819

Abstract

Penelitian ini bertujuan untuk melihat tingkat kelayakan sistem pentanahan yang ada pada bangunan teknik elektro dan elektronika, teknik otomotif dan mesin serta teknik sipil Fakultas Teknik Universitas Negeri Padang. Kualitas sistem pentanahan dapat dilihat dari nilai resistansi yang terukur. Nilai resistansi  pentanahan seharusnya 0 s/d 5 Ω. Faktor yang dapat mempengaruhi nilai pentanahan yaitu kedalaman elektroda, jumlah elektroda, jarak antar elektroda, ukuran konduktor dan jenis tanah.Nilai pentanahan dapat diketahui dengan melakukan pengukuran.Pengukuran pada penelitian ini dilakukan menggunakan alat ukur Earth Tester dengan metode tiga titik. Berdasarkan hasil pengukuran didapatkan nilai rata-rata tahanan pentanahan di bangunan teknik elektro dan elektronika sebesar 48,3Ω. Nilai pada bangunan ini jauh diatas standar  dikarenakan penanaman elektroda pentanahan yang kurang dalam. Sedangkan nilai tahanan pentanahan  pada bangunan teknik mesin dan teknik otomotif  sebesar 2,34 Ω dan teknik sipil sebesar 2,52 Ω. Kedua bangunan tersebut memiliki nilai tahanan pentanahan yang sesuai dengan persyaratan. Dari hasil analisis dapat disimpulkan bahwa  untuk mendapatkan nilai pentanahan ≤ 1 ohm dibutuhkan kedalaman 12 m untuk jenis tanah rawa.