GITA PERMATA LIANSARI
Institut Teknologi Nasional Bandung

Published : 33 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 33 Documents
Search

USULAN PERBAIKAN SISTEM PRODUKSI UNTUK MENGURANGI PEMBOROSAN PADA LANTAI PRODUKSI DENGAN PENDEKATAN KONSEP LEAN MANUFACTURING Bonita, Avissa; Rispianda, Rispianda; Liansari, Gita Permata
REKA INTEGRA Vol 3, No 2 (2015): Edisi Kesepuluh
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (719.846 KB)

Abstract

C59 merupakan perusahaan yang bergerak di bidang industri tekstil. Jenis, model dan ukuran yang beragam pada produk C59 membuat perusahaan tersebut sering mengalami pemborosan. Lean manufacturing merupakan konsep yang bisa digunakan untuk mengatasi permasalahan tersebut. Dengan menggunakan Value Stream Mapping dan perhitungan lead time serta value-to-waste ratio dapat diketahui kondisi perusahaan saat ini. Kondisi tersebut kemudian dianalisis menggunakan metode 5 Why dan metode 5W-1H serta diberikan usulan perbaikan seperti menggunakan material handling, visual control, push system, dan workstation design. Penerapan usulan tersebut dapat menurunkan nilai lead time menjadi 482,758 menit dan menaikan nilai value-to-waste ratio menjadi 2,54 %. Kata Kunci: Lean Manufacturing, Pemborosan, Value Stream Mapping ABSTRACT C59 is a company engaged in the field of textile industry. The variation of Types, models and sizes on C59 products make the company often have waste. Lean manufacturing is a concept that can be used to overcome these problems. By using Value Stream Mapping and calculation of lead time also waste-to- value ratio can be known existing condition of the company. The condition was then analyzed using 5 Why and 5W - 1H method and given the proposed such as using material handling, visual control, push system, and workstation design. Implementation of the proposed improvements could reduce the lead time value into 482.758 minutes and increase the value of value-to-waste ratio to 2.54 % Keywords: Lean Manufacturing, Waste, Value Stream Mapping
Usulan Perbaikan Untuk Mengurangi Jumlah Cacat pada Produk Sandal Eiger S-101 Lightspeed dengan Menggunakan Metode Six Sigma Nailah, Nailah; Harsono, Ambar; LIANSARI, GITA PERMATA
REKA INTEGRA Vol 2, No 2 (2014): Edisi Keenam
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (396.393 KB)

Abstract

Penelitian ini bertujuan untuk membuatusulan perbaikan untuk mengurangi jumlah cacat pada produk sandal dengan menggunakan metode six sigma melalui tahapan DMAIC (Define, Measure, Analyze, Improve, dan Control).Pada tahap define ditemukan jenis cacat yang paling sering terjadi adalah cacat spreading glue is not even. Pada tahap measure didapatkan nilai DPMO sebesar 59.921 dengan nilai sigma sebesar 3,055. Dari hasil analisis menggunakan tree diagram ditemukan faktor-faktor penyebab cacat pada produk diantaranya cara pengeleman yang kurang efektif, kurangnya pemeriksaan terhadap proses, faktor operator, dan faktor lingkungan kerja. Pada tahap improve dilakukan perbaikan terhadap proses dan didapatkan nilai DPMPO sebesar 11.501 dengan nilai sigma sebesar 3,789. Perubahan nilai sigma yang terjadi sebesar 0,734. Pengendalian dapat dilakukandengan cara penggunaan check sheet dan adanya pemeriksaan pada setiap prosesnya agar jumlah cacat dapat terus berkurang. Kata Kunci: six sigma, DMAIC, DPMO, nilai sigma   ABSTRACT This research proposal aims to make improvements to reduce the number of defects in the product sandals using the six sigma DMAIC phases through (Define, Measure, Analyze, Improve, and Control). In the define phase is found types of defects are the most common defect is not even spreading glue. In the measure phase DPMO value of 59 921 obtained with a sigma value of 3.055. From the analysis using a tree diagram of the factors found to cause defects in such products are less effective way of gluing, the lack of examination of the process, the operator factor, and work environment factors. At this stage of repairs to improve the process and obtained values ​​of 11 501 DPMPO the sigma value of 3.789.Changes that occur sigma value of 0.734. Control can be done by use of the check sheet and a hearing on any process in order to continue to decrease the number of defects. Keywords:six sigma, DMAIC, DPMO, sigma value
USULAN PENGENDALIAN KUALITAS PRODUK STANG ENGKOL DI PRODUSEN SENJATA MENGGUNAKAN METODE FAILURE MODE EFFECT ANALYSIS DAN FAULT TREE ANALYSIS (FTA) Muharrahmah, Attaya Risqa; Adianto, Hari; Liansari, Gita Permata
REKA INTEGRA Vol 4, No 2 (2016): Edisi Keempatbelas
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (287.785 KB)

Abstract

Produsen senjata Divisi Tempa & Cor merupakan divisi yang mendukung memproduksi unit usaha internal, memenuhi  permintaan, dan mendukung pasar dalam bidang jasa pengecoran logam tempa. Salah satu produk yang dihasilkan adalah stang engkol yang memiliki jumlah kegagalan yang lebih banyak dibandingkan dengan produk lain. FMEA merupakan suatu metode analisa dari model kerusakan, penyebab dari potensi cacat yang terjadi, akibat dan pengaruh produk secara sistematik. FTA merupakan metode analisa dari pohon kesalahan untuk mengidentifikasi resiko yang berperan terjadinya kegagalan. Dari akar permasalahan yang terjadi dapat ditentukan usulan perbaikan dan pengendalian yang bisa diterapkan pada produsen untuk meminimasi kegagalan yang terjadi. Kata kunci: FMEA, FTA, Stang Engkol   Abstract Arms manufacturer Division of Forging and Casting support to produce internal business unit, demand and to support market, and forging services. One of products produced by the arms manufacturer Forging & Casting Division is a handlebar crank that has number of failures more than the other products.. FMEA is a method analysis of the model damage, cause of the potential defect occur, effect and influence on the product systematically. FTA is a method of fault tree analysis to identify risk contribute to occurrence of failure. The root problem occurs can be determined propose to repair and control that can be applied to the manufacturer to minimize failures.   Keywords: FMEA, FTA, Stang Engkol
USULAN PERBAIKAN PRODUK CACAT MENGGUNAKAN METODE FAULT MODE AND EFFECT ANALYSIS DAN FAULT TREE ANALYSIS PADA PT. SYGMA EXAMEDIA ARKANLEEMA Kartika, Windhi Y; Harsono, Ambar; Liansari, Gita Permata
REKA INTEGRA Vol 4, No 1 (2016): Edisi Ketigabelas
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (429.429 KB)

Abstract

Makalah ini membahas mengenai pengguanaan metode Fault Mode and Effect Analysis (FMEA) untuk mencari prioritas perbaikan produk cacat dan metode Fault Tree Analysis (FTA) untuk mencari akar masalah sebagai dasar usulan perbaikan proses produksi pada perusahaan pencetak Al Qur’an PT. Sygma. Data diambil bulan Januari – September 2015. Cacat membayang merupakan cacat dengan persentase terbanyak yaitu 31%. Pada penelitian ini diambil 8 jenis cacat dari 15 jenis untuk diteliti. Perhitungan RPN pada metode FMEA menghasilkan nilai sebesar 288 untuk cacat isi membayang, isi kotor dan isi mengerut. Terdapat enam jenis cacat yang dicari akar masalahnya dengan menggunakan metode FTA.  Ada beberapa perbaikan yang diusulkan  antara lain penambahan 1-2 operator QC , pembersihan mesin secara rutin, pembuatan dokumen tertulis dan penambahan jumlah lampu di lantai produksi. Kata kunci: Kualitas, Manajemen kualitas, FMEA, RPN, FTA ABSTRACT This paper discusses the use of Fault Mode and Effect Analysis (FMEA) method  to seek priority in  repairing defective products and  Fault Tree Analysis (FTA) method  to find the root of the problem as a basis for the proposed improvement of production processes in PT  Sygma, a Qur'an printing company. Based on data from January - September 2015,  shadow print defect has the highest percentage of  31%. In this study, only 8 from 15 types of defect has been analyzed. The result of RPN calculation in FMEA method   was  288 for shadow print, dirty print and  shrinking paper defect . By using FTA method, the root of the problems of  six types of defect were sought. Several  improvements has been proposed such as  the addition of 1-2 QC operators, routine cleaning of the machine , developing  written document and increasing the number of lights in production area. Keywords : Quality , quality management , FMEA , RPN , FTA
USULAN PERBAIKAN KUALITAS PELAYANAN DI RUMAH MAKAN SARI BUNDO CABANG MERAK DENGAN MENGGUNAKAN METODE SERVICE QUALITY Khairan, Muhammad Farhanul; Arijanto, Sugih; Liansari, Gita Permata
REKA INTEGRA Vol 2, No 3 (2014): Edisi Ketujuh
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (324.513 KB)

Abstract

Salah satu bidang usaha yang cukup menjanjikan pada saat ini adalah usaha dalam bidang kuliner.Rumah makan Sari Bundo cabang Merak merupakan salah satu bidang usaha kuliner makanan khas Sumatra Barat.Banyaknya keluhan dari konsumen terhadap pelayanan yang diberikan, seperti tempat parkir, toilet, dan lokasi rumah makan mengharuskan pihak rumah makan agar segera memperbaikinya.Salah satu caranya dengan mengukur tingkat kepuasan konsumen dengan menggunakan metode Service Quality.Dari hasil pengukuran pada penelitian ini didapatkan nilai rata-rata Gap 5 sebesar -0,052 artinya konsumen secara keseluruhan merasa belum puas dengan pelayanan yang diberikan oleh pihak rumah makan Sari Bundo cabang Merak. Output dari penelitian ini adalah usulan perbaikan kualitas pelayanan bagi pihak rumah makan Sari Bundo cabang Merak. Kata kunci: Kepuasan Pelanggan, Service Quality, Usulan Perbaikan   ABSTRACT One of businesses which isquite promising at the moment is culinary businesses.Merak branch Sari Bundo restaurant is one of the field of West Sumateranese culinary.Many complaints from customers to services provided the restaurant as a parking area, toilet, and the location of restaurant, requires the management to immediately fix it. One of the ways is to measurements the level of customer satisfaction using Service Quality method. A result of measure on this research obtained average value of as much as -0,052 gap 5 witch means consumers has not been satisfied with the service given by Merak branch Sari Bundo restaurant. The output of this research is the proposed improvements the quality of service to management ofMerak branch Sari Bundo restaurant. Keywords:Customer Satisfaction, Service Quality,The Proposed Improvements
USULAN PERBAIKAN SISTEM MANAJEMEN KESELAMATAN DAN KESEHATAN KERJA (SMK3) BERDASARKAN HASIL METODE FAILURE MODE AND EFFECT ANALYSIS (FMEA) DAN PENDEKATAN SAFETY CULTURE Rachmansyah, Arief; Yuniar, Yuniar; Liansari, Gita Permata
REKA INTEGRA Vol 2, No 2 (2014): Edisi Keenam
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (230.049 KB)

Abstract

PT. X adalah perusahaan bidang konstruksi bangunan. PT. X telah menggunakan aturan SMK3 yang ditentukan oleh pemerintah. Tetapi pada kenyataannya masih ditemukan kurangnya rasa kepedulian dan pengawasan  dari perusahaan. Penelitian ini dilakukan untuk mengurangi risiko kecelakaan. Metode yang digunakan adalah metode Failure Mode and Effect Analysis (FMEA). Hasil dari metode FMEA menghasilkan nilai RPN. RPN terbesar digolongkan sebagai potensi bahaya kritis. Nilai RPN yang tergolong potensi bahaya kritis adalah nilai RPN 320, 288 dan 252. Setelah dilakukan perhitungan dengan metode FMEA dilakukan analisis Safety Culture. Analisis Safety Culture dilakukan untuk mengetahui kondisi atau budaya sistem keselamatan di Perusahaan. Safety Culture digunakan sebagai faktor untuk menentukan rekomendasi perbaikan kepada perusahaan.   Kata Kunci : SMK3, Metode FMEA, Safety Culture ABSTRACT PT. X is a building construction company. PT. X has used SMK3 rules set by the government. But in fact still found to lack a sense of awareness and control of the company. This study was done to reduce the risk of accidents. The method used is the method of Failure Mode and Effect Analysis (FMEA). The results of the FMEA method produces RPN value. Largest RPN classified as potential critical hazards. RPN values ​​were classified as potential hazards is a critical value of the RPN 320, 288 and 252. After calculating the FMEA analysis methods Safety Culture. Safety Culture Analysis was conducted to determine the condition of a system or culture of safety in the Company. Safety Culture is used as a factor to determine recommendations for improvement to the company. Keywords: SMK3, FMEA Method, Safety Culture
USULAN PERBAIKAN KUALITAS MENGGUNAKAN METODE SIX SIGMA UNTUK MENGURANGI JUMLAH CACAT PRODUK TAHU PADA PERUSAHAANPENGRAJIN TAHU BOGA RASA Fauziah, Aufi; Harsono, Ambar; Liansari, Gita Permata
REKA INTEGRA Vol 2, No 4 (2014): Edisi Kedelapan
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (659.687 KB)

Abstract

Tahu merupakan salah satu makanan hasil olahan dari bahan  kacang kedelai.  Saat ini produk tahu yang dihasilkan dari tiap adonan memiliki tekstur yang berongga dan ukuran yang tidak seragam. Perlu dilakukan peninjauan terhadap  kinerja proses di perusahaan Pengrajin Tahu Boga Rasa. Perbaikan kualitas ini  dapat  diselesaikan dengan metode SIX  SIGMA melalui  tahap Define, Measure, Analyze, Improve, dan Control. Nilai sigma level dan DPMO sebelum perbaikan sebesar 3,684σ dan 14557,31 . Hal ini menunjukkan bahwa perusahaan belum menerapkan proses produksi dengan baik, karena masih jauh dari  target 6σ. Setelah dilakukan implementasi perbaikan, didapatkan sigma level dan DPMO sebesar 4,003σ dan 890,476. Meningkatnya nilai sigma dan DPMO,dapat dikatakan bahwa  terjadi peningkatan performansi perusahaan. Kata kunci: Perbaikan Kualitas, SIX SIGMA, Jumlah Cacat, DMAIC   ABSTRACT Tofu is one of the foods that produced from soybeans. Nowadays, tofu product that produced from each dough has a hollow texture and variety size from each other. Repairment of this quality can be solved with SIX SIGMA Method through Define, Measure, Analyze, Improve, and Control steps. The sigma level and DPMO before value that we retrieved is 3,684σ and 14557,31. It shows that this company has not applied a good production process because it is still far from the target, which is 6σ. After implementation of improvement the sigma level and DPMO is become 4,003σ and 890,476s. The rise of the sigma value can be said that there is an improvement of performance in the company. Keywords: Quality Improvement, SIX SIGMA, Number of flaws, DMAIC
Usulan Peningkatan Kualitas Pelayanan di Perguruan Tinggi X Dengan Menggunakan Metode Service Quality (Servqual) WASTRANU, I KOMANG; Wahyuning, Caecilia Sri; LIANSARI, GITA PERMATA
REKA INTEGRA Vol 2, No 1 (2014): Edisi Kelima
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (569.62 KB)

Abstract

Perguruan Tinggi X sebagai salah satu dari beberapa Perguruan Tinggi Bandung mengalami ketatnya persaingan dalam menarik minat mahasiswa baru. Tujuan yang ingin dicapai dari penelitian ini adalah mengukur kualitas pelayanan dan memberikan usulan perbaikan kepada pihak manajemen Perguruan Tinggi X untuk mencapai tingkat pelayanan yang diharapkan oleh mahasiswa. Atribut pernyataan yang berjumlah 22 diturunkan berdasarkan lima dimensi menurut Parasuraman, Zeithaml, dan Berry (1988) dalam Tjiptono (2005). Dengan menggunakan instrumen kuesioner sebagai pengumpulan data, maka akan diketahui faktor penyebab ketidakpuasan. Setelah melakukan pengumpulan dan pengolahan data, dapat diketahui bahwa tingkat kepuasan mahasiswa adalah -0,05. Hal ini berarti mahasiswa masih belum puas terhadap kualitas pelayanan yang diberikan.   Kata Kunci: Kepuasan Pelayanan, Perguruan Tinggi, Metode Service Quality, Abstract As one of the University in bandung, University X face the competition with the others university to impress the new students.  The purpose of this study is to measure the service quality of education in University X . Also, this study propose the refinement strategy to the management of University X to match the quality which is students wanted to. There is 22 attributes which is obtained based on five dimension, refer to Parasuraman, Zeithaml, dan Berry (1988) in Tjiptono (2005). By using the questionnaire instrument  as the data collection, the unsatisfactory factor will be determined. after going through the data collection and data processing, the result is that the satisfactory level of students is -0.05. This results show that the students isn’t satisfy to the service quality provided by University X.   Keywords: Satisfaction Services , Higher Education , Method of Service Quality
IMPLEMENTASI SISTEM MATERIAL REQUIREMENT PLANNING (MRP) DAN E-COMMERCE BERBASIS ENTERPRISE RESOURCE PLANNING (ERP) DI PT.XYZ MENGGUNAKAN SOFTWARE ODOO Ridho, Ali; Rispianda, Rispianda; Liansari, Gita Permata
REKA INTEGRA Vol 3, No 3 (2015): Edisi Kesebelas
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1115.167 KB)

Abstract

Makalah ini berisi mengenai implementasi sistem Material Requirement Planning (MRP) dan e-commerce berbasis Enterprise Resource Planning (ERP) di PT.XYZ menggunakan software Odoo. Implementasi ini diperlukan karena saat ini PT.XYZ mendapatkan keluhan dari pelanggan akibat sulitnya mendapatkan produk dari PT.XYZ. Implementasi dilakukan pada aktivitas penjualan, aktivitas produksi dan aktivitas penyimpanan. Modul Odoo yang digunakan diantaranya sales management, purchase management, manufacturing, warehouse, dan website sales. Proses perancangan proses bisnis perusahaan ke dalam software Odoo dilakukan dengan menggunakan proses addition, elimination, automation dan integration. Implementasi ERP yang dilakukan oleh software Odoo menjadikan perpindahan informasi antara proses penjualan menggunakan website lebih cepat dengan proses produksi perusahaan. Kata kunci: MRP, e-commerce, ERP ABSTRACT This paper shows about implementation of Material Requirement Planning (MRP) and e-commerce based on Enterprise Resource Planning (ERP) at PT.XYZ using Odoo software. This implementation is necessary because the current PT.XYZ has complaints from customer due to the difficulty to get product from PT.XYZ. The implementation is done in sales activity, production activity and inventory activity. Odoo modules are implemented including sales management, purchase management, manufacturing, warehouse and website sales. Design process of the company’s business process into Odoo software is done by using addition process, elimination, automation and integration. ERP implementation is done by the software Odoo make transfer of information between the sales process using a website faster with a company's production process. Keywords: MRP, e-commerce, ERP
USULAN PENINGKATAN KUALITAS PELAYANAN JASA PADA BENGKEL HONDA AHMAD YANI DENGAN MENGGUNAKAN METODE IMPORTANCE PERFORMANCE MATRIX Hafez, Oki Saleh; Adianto, Hari; Liansari, Gita Permata
REKA INTEGRA Vol 3, No 3 (2015): Edisi Kesebelas
Publisher : REKA INTEGRA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (722.935 KB)

Abstract

Penelitian ini dilakukan dibengkel Resmi Honda Ahmad Yani Bandung untuk meningkatkan kualitas pelayanan jasa dengan menggunakan metode Importance Performance Matrix (IPM). Data yang digunakan didapat dari hasil penyebaran kuisoner yang terdiri dari 33 pertanyaan berdasarkan 5 dimensi pokok kualitas jasa. Dalam penelitian ini dilakukan perhitungan Nilai Indeks Kinerja (NIK) yang dilakukan secara keseluruhan dan berdasarkan segmentasi. Hasil perhitungan Nilai Indeks Kinerja (NIK) rata-rata, didapat NIK tingkat kepentingan adalah sebesar 3,705 dan NIK tingkat kepuasan sebesar 3,132. Hasil dari perhitungan NIK dipetakan menggunakan metode Importance Performance Matrix (IPM) yang terdiri ke dalam 4 kuadran dalam diagram kartesius dan didapat 9 variabel yang harus dilakukan perbaikan dan peningkatan kualitas jasa. Kata kunci: Pelayanan jasa, Kepuasan pelanggan, Importance Performance Matrix (IPM), Nilai indeks kinerja, usulan perbaikan ABSTRACTThis research was conducted by Honda Ahmad Yani Bandung to improve of service quality using Importance Performance Matrix (IPM). The data used come from the results of questionnaire consisting of 33 questions based on the 5 key dimensions of service quality. In this research the calculation of Value Performance Index (NIK) is performed as a whole and based segmentation. Results of calculation Value Performance Index (NIK) on average, NIK gained importance level is equal to 3,705 and NIK satisfaction level of 3.132. Results of calculation NIK mapped using Importance Performance Matrix (IPM), which consists into 4 quadrants in Cartesian diagram and gained 9 variables that must be repaired and improved quality of services.Keywords : Services , customer satisfaction , Importance Performance Matrix (IPM) , Nilai indeks kinerja , the proposed improvements