Claim Missing Document
Check
Articles

Found 9 Documents
Search

KAJIAN PENYERAPAN LOGAM BERAT AIR RAKSA (Hg) DENGAN MENGGUNAKAN KARBON AKTIF BATUBARA SUB-BITUMINUS YANG DIKARBONISASI (COALITE) Solihin Solihin; Chusharini Chamid; Garlan Sugarba
Bumi Lestari Journal of Environment Vol 9 No 2 (2009)
Publisher : Environmental Research Center (PPLH) of Udayana University

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

One of diversification usage of coal is made for carbon active. The main element in coal which is very useful for carbon active is carbon (C) as other raw materials such as bone, coffee bean, coconut shell, etc. This research used carbonized coal from PT.Bukit Asam as a media to absorb methyl mercury (CH3Hg+2) solution. The carbonized coal has iodine number of ± 386 mg/gram after it was activated at 9000C for 1 hour. It has an adsorption level of 70-80% because the SEM photograph showed a pore size of coarse fraction higher than fine fraction. The degree of saturation is influenced by the grain size of the coal carbon active where the saturation degree of coarse fraction was relatively faster than the fine fraction. Moreover, weightier and bigger debit of carbon active could adsorb higher MeHg concentration.
Evaluasi Batas Nilai Efektif Kadar Sn Menggunakan Analisis Mikroskop dan UC Balance Irham Firmansyah; Solihin; Rully Nurhasan
Jurnal Riset Teknik Pertambangan Volume 2, No. 1, Juli 2022, Jurnal Riset Teknik Pertambangan (JRTP)
Publisher : UPT Publikasi Ilmiah Unisba

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (163.868 KB) | DOI: 10.29313/jrtp.v2i1.780

Abstract

Abstract. PT X has been processing residual tin ore (SHP), land mining and marine mining with a grade of <70%. In order to increase the levels of tin and its associated mineral products to high grade >70% as a requirement for the smelting stage. Tin ore will be analyzed to determine the % content of the sample. Assay analysis can be carried out using a microscope analysis process, unit coefficient balance and chemistry. Microscopy analysis method obtained an average percentage of Sn content of 58.79%, UC Balance analysis of 66.92% and chemical analysis of 58.91%. The level of accuracy produced by the UC Balance analysis tool is the biggest influence on the % of Sn content produced, because it only weighs the specific gravity of cassiterite. The other factors that affect the high error rate generated by the UC Balance analysis are the quality, size, and density of minerals. Meanwhile, the microscope analysis experienced a decrease in the level of accuracy because it was influenced by the quality of the sample and the accuracy of the analyst in distinguishing the types of minerals in each sample. Associated minerals such as ilmenite, zircon, monazite, pyrite and quartz affect the results of the Sn content that will be obtained. The recommended limit for the effective value of microscopy analysis is > 60% and UC Balance analysis is > 70% based on the results of % overall levels. Abstrak. PT X telah melakukan pengolahan bijih timah sisa hasil pengolahan (SHP), penambangan darat dan penambangan laut dengan kadar <70%. Guna meningkatkan kadar timah dan produk mineral ikutannya menjadi high grade >70% sebagai syarat menuju tahap peleburan. Biji timah akan dianalisis untuk mengetahui % kadar sampel. Analisis kadar dapat dilakukan menggunakan proses analisis mikroskop, unit coeficient balance dan kimia. Metode analisis mikroskop mendapatkan hasil ratarata persen kadar Sn sebesar 58,79 %, analisis UC Balance sebesar 66,92 % dan analisis kimia sebesar 58,91 %. Tingkat ketelitian yang dihasilkan oleh alat analisis UC Balance menjadi pengaruh terbesar terhadap % kadar Sn yang dihasilkan, karena hanya menimbang berat jenis kasiterit saja. Adapun faktor lain yang mempengaruhi tingginya tingkat kesalahan yang dihasilkan analisis UC Balance yaitu kualitas, ukuran, berat jenis mineral. Sedangkan pada analisis mikroskop mengalami penurunan tingkat ketelitian karena dipengaruhi oleh kualitas sampel dan ketelitian juru analis dalam membedakan jenis-jenis mineral pada setiap sampel. Mineral ikutan seperti ilmenite, zircon, monazite, pyrit dan kuarsa mempengaruhi hasil nilai kadar Sn yang akan didapatkan. Rekomendasi batas nilai efektif analisis mikroskop > 60 % dan analisis UC Balance > 70 % berdasarkan dari hasil % kadar keseluruhan.
Optimasi Proses Kominusi Bijih Timah Primer Domain Oxide Menggunakan Alat Ball Mill di PT Timah Tbk UPTP Batu Besi, Desa Burong Mandi, Kecamatan Damar, Kabupaten Belitung Timur, Provinsi Kepulauan Bangka Belitung Hardianti Putri; Yunus Ashari; Solihin
Bandung Conference Series: Mining Engineering Vol. 2 No. 1 (2022): Bandung Conference Series: Mining Engineering
Publisher : UNISBA Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (405.045 KB) | DOI: 10.29313/bcsme.v2i1.1887

Abstract

Abstract. Primary Tin Production Unit (UPTP) Batu Besi PT Timah Tbk is one of the mining companies with primary tin mineral deposits. Primary tin deposits are formed from the magmatism process of granite which is a carrier rock or source rock where tin ore is formed with many associated minerals and is bound to each other. There are three types of tin-bearing mineral domains, namely skarn, greissen, and oxide. One that is being processed is oxide with a mineral composition dominated by cassiterite minerals and iron oxide minerals. Tin ore is processed in several stages, namely the comminution stage, size uniformity, and concentration. The comminution process using a ball mill aims to reduce the size of the minerals that are bound together so that they can be properly liberated. Ball mill work with a wet process with the incoming feed material in the form of a slurry (a mixture of water and solids) so as to produce a certain percentage of solid. The grinding operation runs continuously, the material will be eroded due to the force of impact, compression, shear/chipping and abrasion of the material with steel balls in it so as to produce a product in the form of material with a certain fraction. To get the right grain size, it is necessary to pay attention to and optimize the control variables that can affect the grinding process, namely the feed size and the percent solid value used. To determine the exact size of the grinding results using a ball mill, it can be seen from the value of the degree of liberation of the cassiterite mineral in the oxide material. Experiments were carried out with 30 different percent solid values ​​which resulted in different grain sizes so that optimal scouring results could be known. Based on these experiments, the optimal grain size for the concentration process in the shaking table was -325 mesh with a solid percentage of 20%-35%. Abstrak. Unit Produksi Timah Primer (UPTP) Batu Besi PT Timah Tbk merupakan salah satu perusahaan tambang dengan endapan bahan galian timah primer. Endapan timah primer terbentuk dari proses magmatisme batu granit yang merupakan batuan pembawa atau batuan induk tempat bijih timah terbentuk dengan banyak mineral ikutan yang saling berasosiasi dan saling terikat. Terdapat tiga jenis domain mineral pembawa timah yaitu skarn, greissen, dan oxide. Salah satu yang sedang diolah adalah oxide dengan komposisi mineralnya didominasi oleh mineral kasiterit serta mineral oksida besi. Bijih timah diolah dengan beberapa tahapan, yaitu tahap kominusi, penyeragaman ukuran, serta konsentrasi. Proses kominusi menggunakan alat ball mill bertujuan untuk mereduksi ukuran mineral yang saling terikat sehingga dapat terliberasi dengan baik. Ball mill bekerja dengan proses basah (wet) dengan material umpan yang masuk berbentuk slurry (campuran air dan padatan) sehingga menghasilkan nilai persen solid tertentu. Operasi penggerusan berjalan secara kontinu, material akan tergerus karena adanya gaya impact, compression, shear/chipping dan abrasion dari material dengan bola-bola baja di dalamnya sehingga menghasilkan produk berupa material dengan fraksi tertentu. Untuk mendapatkan ukuran butir yang tepat perlu memperhatikan dan mengoptimasi variabel kontrol yang dapat mempengaruhi proses penggerusan yaitu ukuran umpan dan nilai persen solid yang digunakan. Untuk mengetahui ukuran yang tepat dari proses kominusi dengan menggunakan ball mill dapat dilihat dari nilai derajat liberasi mineral kasiterit pada material oxide. Percobaan dilakukan sebanyak 30 nilai persen solid yang berbeda-beda dan menghasilkan ukuran butir yang berbeda-beda pula, sehingga dapat diketahui hasil gerusan yang optimal. Berdasarkan percobaan tersebut diperoleh ukuran butir yang optimal untuk proses konsentrasi pada shaking table adalah -325 mesh dengan persen solid sebesar 20%-35%.
Analisis Lamanya Penimbunan Terhadap Swabakar pada Stockpile Produk Batubara PT. XYZ Dandi Maulana; Solihin
Jurnal Riset Teknik Pertambangan Volume 2, No. 2, Desember 2022, Jurnal Riset Teknik Pertambangan (JRTP)
Publisher : UPT Publikasi Ilmiah Unisba

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29313/jrtp.v2i2.1191

Abstract

Abstract. PT XYZ is a company engaged in the mining sector with coal mining commodities. In meeting consumer needs, the products sold must be based on an agreement between the company and the consumer. This agreement covers the quality, quantity and selling price. To meet the quality that must be done, it is necessary to control and maintain from the start of the mining process until it is accepted by consumers. Coal that has been mined is generally not directly distributed to consumers, but there are several stages that must be passed. In this stage it is stored in a storage area called a stockpile. One of the things that affect the quality and quantity of coal in stock is the problem of self-burning (spontaneous combustion). Self-burning occurs due to coal that has been stacked for too long so that it is exposed to air. Because basically the longer the coal is exposed to air, the more likely it is that the coal will undergo oxidation, which means the greater the possibility of self-burning. The sampling technique is to make 3 artificial piles, each pile as much as 1 Bucket Wheel Loader and then stockpiled in a clean area and tested. The tests carried out are temperature monitoring and coal quality testing. From the tests carried out, it is proven that the length of stockpiling affects the self-burning and changes in quality. Abstrak. PT XYZ merupakan perusahaan yang bergerak di bidang pertambangan dengan komoditas yang ditambang nya berupa batubara. Dalam memenuhi kebutuhan konsumen, hasil produk yang di jual harus berdasarkan pada kesepakatan antara perusahaan dan konsumen. Kesepakatan ini meliputi kualitas, kuantitas dan harga jual. Untuk memenuhi kualitas yang telah di sepakati maka perlu adanya pengontrolan dan perawatan dari mulai proses penambangan berlangsung hingga diterima oleh konsumen. Batubara yang telah di tambang umumnya tidak langsung didistribusikan ke pihak konsumen, namun terdapat beberapa tahapan yang perlu dilalui. Dalam tahapan tersebut batubara disimpan di tempat penyimpanan yang disebut dengan stockpile. Salah satu hal yang mempengaruhi kualitas dan kuantitas batubara pada stockpile yaitu permasalahan swabakar (spontaneous combustion). Swabakar terjadi akibat batubara yang ditumpuk terlalu lama sehingga terekspose dengan udara. Karena pada dasarnya semakin lama batubara terekspos dengan udara, akan semakin besar kemungkinan batubara tersebut mengalami oksidasi yang berarti semakin besar pula kemungkinan terjadinya swabakar. Teknis pengambilan sampel yaitu membuat 3 timbunan buatan, masing-masing timbunan sebanyak 1 Bucket Wheel Loader kemudian di timbun di area yang clean dan dilakukan pengujian. Pengujian yang dilakukan yaitu monitoring temperatur dan pengujian kualitas batubara. Dari pengujian yang dilakukan terbukti bahwa lama penimbunan mempengaruhi swabakar dan perubahan kualitas.
Studi Pendahuluan Pengaruh Fly Ash pada Netralisasi Air Asam Tambang di Penambangan Batubara PT XYZ, Kabupaten Kutai Kartanegara, Provinsi Kalimantan Timur Gumilar Rayana; Sri Widayati; Solihin
Bandung Conference Series: Mining Engineering Vol. 3 No. 1 (2023): Bandung Conference Series: Mining Engineering
Publisher : UNISBA Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29313/bcsme.v3i1.5693

Abstract

Abstract. Acid mine drainage can affect water quality in the area which requires an authority to improve water quality in mining areas. So that the neutralization of acid mine drainage must be carried out, one of which is using fly ash. Fly Ash has alkaline properties with a pH value between 4.5 to 12. The pH value of fly ash is determined by the sulfur content of the coal parent material. Therefore fly ash can increase the pH value of acid mine water. The research method used in this study is the active method by mixing fly ash into the water in the settling pond which has a pH value of less than 7, it aims to neutralize the pH value in the settling pond. From the previous testing, it was found that the effect of fly ash on neutralizing acid mine drainage required a fly ash dose of 60 gr/L with a pH value of 7.57, then a linear regression calculation was performed to determine the optimal value of 58.35 gr/L for a pH value of 7. Then The dose was neutralized to acid mine drainage which has a pH value of less than 7, so that a dose value was obtained within 31 days of 632.21 gr/L or 381.532 kg/month. In addition to the effect of fly ash on the pH value, a calculation of the effect of fly ash with the same dose of neutralizing the pH value on the decrease in Fe and Mn levels was also carried out. The effect of decreasing the previous Fe content with an average value of 7.33 mg/L becomes 5.57 mg/L, and the effect of the previous Mn content with an average value of 4.32 mg/L becomes 3.56 mg/L Abstrak. Air asam tambang dapat mempengaruhi kualitas air di daerah tersebut yang membutuhkan suatu kewenangan untuk dapat memperbaiki kualitas air di daerah pertambangan. Sehingga kegiatan penetralan air asam tambang harus dilakukan salah satunya menggunakan Fly ash. Fly Ash memiliki sifat alkalin yang memiliki nilai pH antara 4,5 sampai 12. Nilai pH yang dimiliki fly ash ditentukan oleh kandungan sulfur bahan induk batubara. Oleh karena itu fly ash dapat menaikan nilai pH air asam tambang. Berdasarkan latar belakang tersebut maka penelitian ini dilakukan untuk mengetahui pengaruh penggunaan fly ash terhadap proses penetralan air asam tambang. Metode penelitian yang digunakan pada penelitian ini yaitu metode aktif dengan cara mencampurkan fly ash ke dalam air di kolam pengendapan yang memiliki nilai pH kurang dari 7, hal tersebut bertujuan untuk dapat menetralkan nilai pH di kolam pengendapan Dari pengujian yang dilakukan bahwasannya pengaruh fly ash terhadap penetralan air asam tambang dibutuhkan dosis fly ash sebesar 60 gr/L dengan nilai pH sebesar 7.57, lalu dilakukan perhitungan linier regresi untuk mengetahui nilai optimal sebesar 58.35 gr/L untuk nilai pH 7. Kemudian dosis tersebut dilakukan penetralan terhadap air asam tambang yang memiliki nilai pH kurang dari 7, sehingga didapatkan nilai dosis dalam waktu 31 hari sebesar 632.21 gr/L atau 381.532 kg/bulan. Selain pengaruh fly ash terhadap nilai pH, juga dilakukan perhitungan pengaruh fly ash dengan dosis yang sama dengan penetralan nilai pH terhadap penurunan kadar Fe dan kadar Mn. Pengaruh penurunan kadar Fe yang sebelumnya dengan nilai rata – rata 7.33 mg/L menjadi 5.56 mg/L, dan pengaruh kadar Mn yang sebelumnya dengan nilai rata – rata 4.32 mg/L menjadi 3.56 mg/L
Studi Pendahuluan Pengelolaan Air Asam Tambang Menggunakan Karbon Aktif Fine Coal di Penambangan Batubara pada Kolam Pengendapan Kabupaten Kutai Kartanegara, Provinsi Kalimantan Timur Muhammad Aziz Rahmatullah; Sri Widayati; Solihin
Bandung Conference Series: Mining Engineering Vol. 3 No. 1 (2023): Bandung Conference Series: Mining Engineering
Publisher : UNISBA Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29313/bcsme.v3i1.5739

Abstract

Abstract. Acid mine water is water that has a low pH (pH<5) which contains various dissolved metals such as iron (Fe), manganese (Mn), and other sulfate compounds. Acid mine water has an impact in the form of environmental pollution, so it is necessary to handle acid mine drainage using activated carbon so that it does not affect the surrounding environment. The research method used in this study is the active method by mixing activated carbon into 6 settling ponds, it aims to be able to determine the effect of activated carbon on settling ponds in the form of pH and Fe and Mn levels based on standard water quality standards.The rate of decrease in Fe metal content and Mn metal content after mixing using activated charcoal was 76,0% for Fe metal content and 18,60% for Mn metal content. The need for activated carbon for 31 days for the purpose of neutralizing acid mine water is 154790,8 kg/liter. Abstrak. Air asam tambang merupakan air yang memiliki pH rendah (pH<5) yang mengandung berbagai logam terlarut seperti besi (Fe), mangan (Mn), serta senyawa sulfat lainnya. Air asam tambang menimbulkan dampak berupa terjadinya pencemaran lingkungan sehingga perlu dilakukannya penanganan air asam tambang dengan menggunakan Karbon aktif sehingga tidak mempengaruhi lingkungan sekitar. Metode penelitian yang digunakan pada penelitian ini yaitu metode aktif dengan cara mencampurkan Karbon aktif kedalam 6 kolam pengendapan, hal tersebut bertujuan untuk dapat mengetahui pengaruh karbon aktif pada kolam pengendapan berupa pH serta kadar Fe dan Mn dengan berdasarkan standar nilai baku mutu air. Laju penurunan kadar logam Fe dan kadar logam Mn setelah pencampuran dengan menggunakan Karbon aktif yaitu sebesar 76,0% untuk kadar logam Fe dan 18,60 % untuk kadar logam Mn. Kebutuhan karbon aktif selama 31 hari untuk keperluan penetralan air asam tambang sebesar 154790,8 kg/liter.
Pengelolaan Air Asam Tambang Menggunakan Karbon Aktif Fine Coal di Penambangan Batubara Muhammad Aziz Rahmatullah; Sri Widayati; Solihin
Jurnal Riset Teknik Pertambangan Volume 3, No. 1, Juli 2023, Jurnal Riset Teknik Pertambangan (JRTP)
Publisher : UPT Publikasi Ilmiah Unisba

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29313/jrtp.v3i1.2126

Abstract

Abstract. Acid mine water is water that has a low pH (pH<5) which contains various dissolved metals such as iron (Fe), manganese (Mn), and other sulfate compounds. Acid mine water has an impact in the form of environmental pollution, so it is necessary to handle Acid Mine Drainage using activated carbon so that it does not affect the surrounding environment. The research method used in this study is the active method by mixing activated carbon into 6 settling ponds, it aims to be able to determine the effect of activated carbon on settling ponds in the form of pH and Fe and Mn levels based on standard water quality standards.The rate of decrease in Fe metal content and Mn metal content after mixing using activated charcoal was 76,0% for Fe metal content and 18,60% for Mn metal content. The need for activated carbon for 31 days for the purpose of neutralizing acid mine water is 154790,8 kg/liter. Abstrak. Air asam tambang merupakan air yang memiliki pH rendah (pH<5) yang mengandung berbagai logam terlarut seperti besi (Fe), mangan (Mn), serta senyawa sulfat lainnya. Air asam tambang menimbulkan dampak berupa terjadinya pencemaran lingkungan sehingga perlu dilakukannya penanganan air asam tambang dengan menggunakan Karbon aktif sehingga tidak mempengaruhi lingkungan sekitar. Metode penelitian yang digunakan pada penelitian ini yaitu metode aktif dengan cara mencampurkan Karbon aktif kedalam 6 kolam pengendapan, hal tersebut bertujuan untuk dapat mengetahui pengaruh karbon aktif pada kolam pengendapan berupa pH serta kadar Fe dan Mn dengan berdasarkan standar nilai baku mutu air. Laju penurunan kadar logam Fe dan kadar logam Mn setelah pencampuran dengan menggunakan Karbon aktif yaitu sebesar 76,0% untuk kadar logam Fe dan 18,60 % untuk kadar logam Mn. Kebutuhan karbon aktif selama 31 hari untuk keperluan penetralan air asam tambang sebesar 154790,8 kg/liter.
Analisis Lamanya Penimbunan Terhadap Swabakar pada Stockpile Produk Batubara PT. XYZ Dandi Maulana; Solihin
Jurnal Riset Teknik Pertambangan Volume 2, No. 2, Desember 2022, Jurnal Riset Teknik Pertambangan (JRTP)
Publisher : UPT Publikasi Ilmiah Unisba

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29313/jrtp.v2i2.1191

Abstract

Abstract. PT XYZ is a company engaged in the mining sector with coal mining commodities. In meeting consumer needs, the products sold must be based on an agreement between the company and the consumer. This agreement covers the quality, quantity and selling price. To meet the quality that must be done, it is necessary to control and maintain from the start of the mining process until it is accepted by consumers. Coal that has been mined is generally not directly distributed to consumers, but there are several stages that must be passed. In this stage it is stored in a storage area called a stockpile. One of the things that affect the quality and quantity of coal in stock is the problem of self-burning (spontaneous combustion). Self-burning occurs due to coal that has been stacked for too long so that it is exposed to air. Because basically the longer the coal is exposed to air, the more likely it is that the coal will undergo oxidation, which means the greater the possibility of self-burning. The sampling technique is to make 3 artificial piles, each pile as much as 1 Bucket Wheel Loader and then stockpiled in a clean area and tested. The tests carried out are temperature monitoring and coal quality testing. From the tests carried out, it is proven that the length of stockpiling affects the self-burning and changes in quality. Abstrak. PT XYZ merupakan perusahaan yang bergerak di bidang pertambangan dengan komoditas yang ditambang nya berupa batubara. Dalam memenuhi kebutuhan konsumen, hasil produk yang di jual harus berdasarkan pada kesepakatan antara perusahaan dan konsumen. Kesepakatan ini meliputi kualitas, kuantitas dan harga jual. Untuk memenuhi kualitas yang telah di sepakati maka perlu adanya pengontrolan dan perawatan dari mulai proses penambangan berlangsung hingga diterima oleh konsumen. Batubara yang telah di tambang umumnya tidak langsung didistribusikan ke pihak konsumen, namun terdapat beberapa tahapan yang perlu dilalui. Dalam tahapan tersebut batubara disimpan di tempat penyimpanan yang disebut dengan stockpile. Salah satu hal yang mempengaruhi kualitas dan kuantitas batubara pada stockpile yaitu permasalahan swabakar (spontaneous combustion). Swabakar terjadi akibat batubara yang ditumpuk terlalu lama sehingga terekspose dengan udara. Karena pada dasarnya semakin lama batubara terekspos dengan udara, akan semakin besar kemungkinan batubara tersebut mengalami oksidasi yang berarti semakin besar pula kemungkinan terjadinya swabakar. Teknis pengambilan sampel yaitu membuat 3 timbunan buatan, masing-masing timbunan sebanyak 1 Bucket Wheel Loader kemudian di timbun di area yang clean dan dilakukan pengujian. Pengujian yang dilakukan yaitu monitoring temperatur dan pengujian kualitas batubara. Dari pengujian yang dilakukan terbukti bahwa lama penimbunan mempengaruhi swabakar dan perubahan kualitas.
Penentuan Zona Alterasi Hidrotermal dari Bijih Emas Tujuh Bukit Naufal Abdan S.; Solihin; Yunus Ashari
Jurnal Riset Teknik Pertambangan Volume 3, No. 2, Desember 2023, Jurnal Riset Teknik Pertambangan (JRTP)
Publisher : UPT Publikasi Ilmiah Unisba

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29313/jrtp.v3i2.2813

Abstract

Abstract. Indonesia, situated along the copper-gold belt, establishes itself as one of the world's largest gold producers, ranking among the top 10. This is attributed to the magmatic belt formed by the convection currents of magma, pushing tectonic plates to create uplift fault zones. These zones serve as pathways for hydrothermal fluids to reach the Earth's surface, forming alteration zones where chemical reactions occur between hydrothermal solutions and surrounding rocks, resulting in mineralization pathways. Tujuh Bukit, one of the largest gold deposits in Indonesia, is formed from porphyry and intermediate to high-sulfide epithermal ore types. This research employs the Corbet and Leach method to determine alteration zones in samples from the Tujuh Bukit area. The study reveals that differences in alteration zones, such as advanced argilic and argilic, impact gold ore formation. The advanced argilic zone exhibits higher temperatures and lower pH compared to the argilic zone. Samples falling within the advanced argilic zone are characterized by the presence of alunite, a product of silicate alteration by sulfuric acid. Quartz content also influences pH and temperature during the alteration process, while one sample falls into the argilic zone. The research involves the collection of secondary and primary data, including geological maps, weather data, X-Ray Diffraction analysis, and Mineralogical Analysis. Abstrak. Indonesia, sebagai salah satu negara yang terletak pada jalur copper-gold belt, mendudukkan dirinya sebagai salah satu produsen emas terbesar di dunia, masuk dalam 10 besar. Keadaan ini disebabkan oleh jalur magmatis yang terbentuk akibat arus konveksi magma, mendorong lempeng tektonik membentuk zona sesar naik. Zona ini menjadi jalur lemah bagi cairan hidrotermal untuk mencapai permukaan bumi, membentuk zona alterasi tempat terjadinya reaksi kimia antara larutan hidrotermal dan batuan sekitarnya, menghasilkan jalur mineralisasi. Tujuh Bukit, salah satu deposit emas terbesar di Indonesia, terbentuk dari bijih tipe porfiri dan epitermal sulfida menengah hingga tinggi. Penelitian ini menggunakan metode Corbet dan Leach untuk menentukan zona alterasi pada sampel di daerah Tujuh Bukit. Hasil penelitian menunjukkan bahwa perbedaan zona alterasi, seperti advanced argilic dan argilic, mempengaruhi pembentukan bijih emas. Zona advanced argilic memiliki temperatur lebih tinggi dan pH lebih rendah dibandingkan zona argilic. Sampel yang termasuk ke dalam zona advanced argilic ditandai dengan keterdapatan alunit hasil perombakan silikat oleh asam sulfat. Kandungan kuarsa juga berpengaruh terhadap pH dan temperatur selama proses alterasi, sementara satu sampel masuk ke zona argilic. Penelitian ini melibatkan pengumpulan data sekunder dan primer, termasuk peta geologi, data cuaca, analisis X-Ray Diffraction, dan Analisis Mineragrafi.