Claim Missing Document
Check
Articles

Found 3 Documents
Search

Penggunaan ETAP 12.6 Sebagai Alat Bantu Dalam Memilih Setting OCR Untuk Melindungi Kelangsungan dan Kestabilan Energi Listrik Hidayat, Renaldi; Kartadinata, V. Budi; Olivia Sereati, Catherine; Octavianus Bachri, Karel
Jurnal Elektro Vol 15 No 2 (2022): Vol.15 No.2 Oktober 2022: Jurnal Elektro
Publisher : Prodi Teknik Elektro, Fakultas Teknik Unika Atma Jaya Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25170/jurnalelektro.v15i2.5112

Abstract

In this time electrical energy is one of the most energy used. In industry electrical energy becomes a necessity that cannot be separated from the production process. Due to the need for electrical energy sources, of course, a protection system is needed to maintain the continuity and stability of electrical energy from existing disturbances such as short circuit disturbances. To overcome the short circuit, OCR is used. To assist the process of calculating loadflow and short-circuit current, ETAP12.6 is used. The results of the analysis of the ETAP 12.6 will be compared with the data obtained in the field with the aim of analyzing whether the use of the ETAP 12.6 software in assisting calculations and analysis in the selection of OCR settings. The difference in ocr settings in the ETAP 12.6 and field data has a difference of less than 2%. This difference is relatively small and can still be used to help the process in selecting the OCR settings.
Simulasi Sistem Pengendalian Motor Stepper dengan Metode Pulse Width Modulation Timothy Wijaya, Hans; Pangestu, Devin; Timothy Sutjipto, Marcellus; Surya Widjaja, Williem; Octavianus Bachri, Karel; Nur, Tajuddin
Jurnal Elektro Vol 15 No 1 (2022): Vol.15 No.1 April 2022: Jurnal Elektro
Publisher : Prodi Teknik Elektro, Fakultas Teknik Unika Atma Jaya Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25170/jurnalelektro.v15i1.5120

Abstract

This paper discusses the control of a stepper motor using Pulse Width Modulation (PWM) methods. In this paper, the author presents two designs: one using a stepper motor controller with an astable multivibrator as a pulse generator and the other utilizing a microcontroller as the pulse generator. The design of the stepper motor controller with an astable multivibrator involves using the IC timer 555 to control the stepper motor speed and a latch circuit to control the direction of the stepper motor rotation. Meanwhile, the design of the stepper motor controller with a microcontroller employs the Arduino UNO R3 to control both the direction and speed of the stepper motor. Testing is conducted through a simulation of the system design using Proteus software. From the test results, it is observed that an increase in the PWM value leads to a faster rotation speed of the stepper motor, conversely, a decrease in PWM value results in a slower rotation speed of the stepper motor.
Pelatihan Elektronika Dasar untuk Guru dan Siswa Kelas VIII SMP di Cilincing Jakarta Utara Rippun G. Manalu, Ferry; Octaviani, Sandra; Octavianus Bachri, Karel; Surya Permana, Rizky; Olivia Sereati, Catherine
SABDAMAS Vol 2 No 1 (2023): SABDAMAS
Publisher : Lembaga Penelitian dan Pengabdian kepada Masyarakat Unika Atma Jaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25170/sabdamas.v2i1.5011

Abstract

Pada Juni 2019, prodi Teknik Elektro Fakultas Teknik Unika Atma Jaya telah menyelenggarakan program pengabdian kepada masyarakat dengan tema memberi pembekalan tangan keterampilan dasar elektronika kepada SMP Kristen Harapan bagi Bangsa di Cilincing Jakarta Utara. Program ini mendapatkan tanggapan yang positif dari guru dan siswa. Berdasarkan hasil evaluasi kegiatan sebelumnya, seluruh siswa (100%) ingin kegiatan ini diadakan lagi dengan materi lanjutan. Pada kegiatan sebelumnya guru belum dilibatkan dalam proses, sehingga keberlanjutan program tidak dapat dilaksanakan secara rutin di sekolah. Oleh karena itu, pada program ini, selain melanjutkan pelatihan kepada siswa kelas VIII, guru juga dilibatkan dalam pembekalan untuk menyelenggarakan program ekstrakurikuler mengenai dasar elektronika selanjutnya. Pelatihan elektronika yang akan dilaksanakan pada pengabdian masyarakat ini difokuskan untuk siswa kelas VIII dan meliputi materi membuat PCB, pengenalan project board, pengenalan komponen elektronika dan fungsi-fungsinya. Pada tahapan ini peserta sudah mampu membuat rangkaian sederhana, membuat prototipe rangkaian elektronika menggunakan project board dan diimplementasikan dalam electronic kit. Kegiatan pengabdian ini diharapkan dapat melengkapi keterampilan siswa dan guru dalam bidang elektronika sehingga siap dalam menghadapi kemajuan teknologi, khususnya di bidang Teknik Elektro