Article Per Year (5 Year)
p-Index From 2021 - 2026
0.751
P-Index
This Author published in this journals
All Journal Bulletin of Electrical Engineering and Informatics
Aman, Fazlul
Unknown Affiliation
Electrical & Electronics Engineering

Published : 4 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search

 1 
Evaluation of steady-state ground resistance by field measurement and CDEGS computation Muhammad, Usman; Zaid, Hadee; Ahmad, Nurul Nadia; Mohamad Nor, Normiza; Aman, Fazlul
Bulletin of Electrical Engineering and Informatics Vol 13, No 5: October 2024
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v13i5.7603

Abstract

In addition to the soil resistivity and size of the grounding system, grounding system configuration can influence the steady-state resistance (RDC) of a grounding system. The RDC of four to six configurations in three distinct soil conditions (sites 1 to 3) is measured using the fall-of-potential method and computed using the current distribution, electromagnetic fields, grounding, and soil structure analysis (CDEGS) simulation. The RDC value generally decreases as size increases, i.e., when more rods or tapes are added, except for a little variation subject to the electrode arrangement and soil resistivity. The 3 and 4-parallel configurations perform better on low resistivity soil (site 1), while the grid configurations (2×2- and 3-rod grids) are better on high resistivity soil (site 2). The difference between the measured and computed values at high soil resistivity sites (sites 2 and 3) is large, ranging from 18% to 66% for site 2 and from 35% to 53% for site 3. The difference is lower and more consistent at site 1, where five out of six configurations achieve less than 10%. At all sites, the difference between computed and measured RDCs generally decreases as the area of the electrode increases, except for some cases at site 2.
Comparative field assessment of grounding enhancement material for electrical earthing system Zhe Kang, Lim; Chun Lim, Siow; Muhammad, Usman; Aman, Fazlul; Nor, Normiza Mohamad
Bulletin of Electrical Engineering and Informatics Vol 13, No 5: October 2024
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v13i5.7303

Abstract

Grounding enhancement material (GEM) is used to lower the earthing resistance value of a given earthing system. In this paper, a commercially available GEM is experimented at the field alongside with Sodium Chloride, Copper II Sulphate and planting soil. The well established Wenner’s 4 pole method and fall of potential method was employed to measure the soil resistivity and earthing resistance respectively. It was found that the salts i.e., Sodium Chloride and Copper II Sulphate are superior in reducing the earthing resistance as reduction of more than 85% were observed. However, the commercial GEM has exhibited the most stable earthing resistance value over a period of 101 days, exhibiting the lowest standard deviation. This seems to suggest that the commercial GEM has superior moisture retention capability. This study also proven that Sodium Chloride can be dissolved by heavy downpour and replenishing it periodically is needed in a tropical country like Malaysia with regular thunderstorms and heavy downpours.
Comparing horizontal versus vertical arrangement on the ground resistance values Shamsul, Syakir Azim; Muhammad, Usman; Aman, Fazlul; Mohamad Nor, Normiza; Osman, Miszaina
Bulletin of Electrical Engineering and Informatics Vol 13, No 6: December 2024
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v13i6.7944

Abstract

It is important to compare the horizontal electrodes versus vertical ground electrodes particularly when there is limited area to extend the horizontal ground electrode and hard soil at the deeper soil in order to install the vertical rod electrode. Although all of these can be assessed by computational work, much work has shown that computed resistance values are different than measured resistance values and these computational softwares are not always available to the users. For these reasons, the aim of this paper is to address this shortfall by considering two sites with two-layer soil resistivity model where site 1 with upper layer higher than the lower layer and vice versa for site 2. For the same size of ground electrodes, vertical arrangement is found to have lower ground resistance values, despite higher soil resistivity at the lower layer soil. Soil compaction after backfilling the trench during the installation of horizontal electrode has been identified as the main factor that contributes to differences between the measured and computed resistance values.
Influences of impulse generators on the impulse characteristics of grounding systems Muhammad, Usman; Aman, Fazlul; Mohamad Nor, Normiza; Nadia Ahmad, Nurul; Osman, Miszaina
Bulletin of Electrical Engineering and Informatics Vol 14, No 3: June 2025
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v14i3.8467

Abstract

It is important to ensure the effectiveness of the experimental test set up and to accurately characterize grounding systems under high impulse conditions, the study on the effect of impulse generator is therefore needed. As with other experimental work, the test results may be influenced not only by the characteristics of the test load under study, but also the test arrangement, rating of the impulse generator and transducers. In this work, sources of this overshoot/spike observed in voltage and current traces of 1-rod, 3-rod, and 4-rod electrodes subjected to two impulse current generators of different rating: generating at maximum voltage and current of 100 kV, 1.5 kA, and 300 kV, 10 kA with the same response time of 1.2/50 μs are identified with the aid of simulation work.
Co-Authors Ahmad, Nurul Nadia Chun Lim, Siow Mohamad Nor, Normiza Muhammad, Usman Nadia Ahmad, Nurul Nor, Normiza Mohamad Osman, Miszaina Shamsul, Syakir Azim Zaid, Hadee Zhe Kang, Lim