Article Per Year (5 Year)
p-Index From 2021 - 2026
0.408
P-Index
This Author published in this journals
All Journal Journal of Applied Mechanical Engineering and Renewable Energy (JAMERE)
Joni Pasau, Fransye
Unknown Affiliation
Agriculture, Biological Sciences & Forestry Automotive Engineering Chemical Engineering, Chemistry & Bioengineering Civil Engineering, Building, Construction & Architecture Computer Science & IT Control & Systems Engineering Decision Sciences, Operations Research & Management Earth & Planetary Sciences Electrical & Electronics Engineering Energy Engineering Environmental Science Industrial & Manufacturing Engineering Materials Science & Nanotechnology

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
Pengaruh Jenis Pahat Terhadap Nilai Kekasaran Permukaan Material Baja Carbon S45C Maryanti, Budha; Rezaldy, Rezaldy; Joni Pasau, Fransye
Journal of Applied Mechanical Engineering and Renewable Energy Vol 5 No 1: February 2025
Publisher : Indonesian Society of Applied Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.52158/jamere.v5i1.1097

Abstract

In the turning process, the surface finish of a workpiece can influence the level of visual quality of a workpiece. CNC machine cutting parameters include feed speed, feed depth, and cutting speed. The aim of this research is to determine the effect of carbide insert tool types ZCC WNMG 060408 – DM and VBMT 160408 – HM on the average roughness value in the turning process with a rotational speed of 500 rpm and feed speed variations of 0.10 mm/rev, 0.15 mm/ rev and 0.20 mm/rev on S45C steel material. This research is located at PT. Bin Smeer Jaya with the research sample, namely S45C steel material. This research will be carried out with 3 samples of surface roughness testing each with varying feeding, where the turning process will be carried out on a CNC lathe machine first using ZCC WNMG 060408 – DM and VBMT 160408 – HM carbide insert chisels. The desired roughness standard is 1.8 µm – 2.2 µm. Based on the results of testing the surface roughness value of S45C steel material, the data obtained using the Handysurf E-35 surface roughness measurement tool, the roughness value using the ZCC WNMG 060408 – DM specimen 3 feeding 0.20 mm/rev carbide insert chisel was 2.38 µm, whereas for specimen 3 feeding 0.10 mm/rev is 4.11 µm. Then for the VBMT 160408 – HM carbide insert chisel, specimen 1 feeding 0.10 mm/rev is 1.48 µm, while for specimen 2 feeding 0.20 mm/rev it is 4.41 µm. So it can be concluded that the lowest roughness value occurs in the VBMT 160408 – HM carbide insert chisel compared to the ZCC WNMG 060408 – DM carbide insert chisel type. Therefore, the best level of surface roughness results occurs in the VBMT 160408 – HM carbide insert with the desired roughness standard and optimal visual quality
Analisisi Penelitian Performansi Pompa Air Pada Divisi Persemaian Di Kalimantan Timur Ferdnian, Marsius; Joni Pasau, Fransye
Journal of Applied Mechanical Engineering and Renewable Energy Vol 5 No 2 (2025)
Publisher : Indonesian Society of Applied Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.52158/jamere.v5i2.1266

Abstract

The engine pump is used to move fluids by converting mechanical energy into fluid energy and pressure, then transporting the fluid through the piping system. The use of pumps to meet clean water needs. The method with the working principle or how the pump flows fluids or provides fluid power, the results of the study show that the pump capacity with a water discharge of 15 L / m, the total head is 4.807 m, and after knowing the curve where there is an increase in pressure at the outlet (discharge pressure) there will be a decrease in the amount of flow and the higher the amount of flow that comes out, the higher the pressure capacity of the fluid. In the demin water transfer pump, it is known that the available NPSH (6.7 meters) is greater than the required NPSH (6.2 meters), so the pump can. So to fill the water reservoir at the Permanent Nursery Service, the pump operates for 8.5 hours per day. Data analysis and discussion can be concluded that the pump capacity with a water discharge of 15 L/m, the total head is 4.807 m, In the demin water transfer pump it is known that the available NPSH (6.7 meters) is greater than the required NPSH (6.2 meters), so the pump can work without experiencing cavitation. So to meet the needs of the water reservoir in the Permanent Nursery Division, the pump operates for 8-5 hours per day.
Co-Authors Budha Maryanti Ferdnian, Marsius Rezaldy, Rezaldy