cover
Contact Name
Dewi Muliyati
Contact Email
dmuliyati@unj.ac.id
Phone
-
Journal Mail Official
snf@unj.ac.id
Editorial Address
Fisika FMIPA Universitas Negeri Jakarta GHA Lt.5 Jl Rawamangun Muka No.1
Location
Kota adm. jakarta timur,
Dki jakarta
INDONESIA
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL)
ISSN : 23021829     EISSN : 24769398     DOI : https://doi.org/10.21009/03
Focus and Scope: Physics education Physics Instrumentation and Computation Material Physics Medical Physics and Biophysics Physics of Earth and Space Physics Theory, Particle, and Nuclear Environmental Physics and Renewable Energy
Articles 977 Documents
SAKLAR OTOMATIS BERBASIS LIGHT DEPENDENT RESISTOR (LDR) PADA MIKROKONTROLER ARDUINO UNO Angga Khalifah Tsauqi; Murtezha Hadijaya; Ivander Manuel; Venas Miftah Hasan; Annisa Tsalsabila; Fadhilah Chandra; Titin Yuliana; Putri Tarigan; Irzaman Irzaman
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (764.769 KB) | DOI: 10.21009/0305020105

Abstract

Has succeeded in making switch automatic based light dependent resistor ( LDR)in mikrokontroler arduino uno .Switch this tested in two conditions yatu in laboraatrium and in roomy .On condition laboratory , voltage enter of 5.00 volts managed to turn switch , where switch burns in the state of life ( ON ) producing a voltage of 3.74 volts and obstacles of 230 -260 ohm , while switch die ( OFF ) producing a voltage of 4.78 volts and obstacles switch of 44 - 45 ohm , with strong lighting in laboratoium at 15 lux is the verge of a function of switch in the laboratory .On condition in roomy , strong lighting the function switch of 70 lux with obstacles switch equal to 100 ohm .The difference the function obstacles switch this caused by the strong illumination that produced by a lamp in the laboratory compared with strong illumination that produced by the eye day . Kata kunci: saklar otomatis, LDR, mikrokontroler,kuat penerangan, lux.
RANCANG BANGUN ALAT PEMANTAU PASANG SURUT AIR LAUT MELALUI JARINGAN INTERNET UNTUK KAWASAN TELUK KENDARI Bardan Bulaka; Hendro Hendro
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (637.899 KB) | DOI: 10.21009/0305020106

Abstract

English version of the abstract be written here. Has created a system monitor water levels that can be used to monitor the phenomenon of the tide in the Gulf of Kendari by using the Internet network. Hardware or device used consisted of an ultrasonic sensor is used to measure the distance of the surface of the water, the microcontroller Arduino Uno that serves to process data readings from ultrasonic sensors and WiFi module ESP8266 ESP-01 which serves to connect the microcontroller to the Internet network (data server) , The hardware of the system is tested on the water surface inside a container penampukan water, where the water level inside the container is assumed as the sea level. Tests conducted to determine the feasibility of such a device before it is applied in the area of ​​Teluk Kendari. Data from the measurement of the water level can be accessed by anyone with a browser using either a computer (PC), laptop, or smartphone connected to the Internet network. Applications used to monitor water levels through the Internet is ThingSpeak contained on the website www.thingspeak.com. Keywords: Monitors, Sensors, Microcontroller, Internet, ThingSpeak.
PEMBUATAN PROTOTIPE SISTEM KEAMANAN LABORATORIUM BERBASIS ARDUINO MEGA Gagat Mughni Pradipta; Nida Nabilah; Hannif Izzatul Islam; Dendy Handy Saputra; Sofyan Said; Ade Kurniawan; Heriyanto Syafutra; Shelvie Nidya Neiman; Irzaman Irzaman
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (858.481 KB) | DOI: 10.21009/0305020107

Abstract

We has been successfully creating a laboratory security system prototype based on Arduino Mega. This device assisted with PIR sensor (passive infrared) and RFID (Radio Frequency Identifier). In experiments carried out study the sensitivity of the PIR sensor at a distance of 0 meters, 0.5 meters, 1 meters, 1.5 meters, 2 meters, 2.5 meters, 3 meters, 3.5 meters and 4 meters then at an angle of 00, 300, 450, and 600 with the source of motion is the human’s body movement. In this study data showed that at a distance of 2 .5 meters at an angle of 60 degrees PIR was not able to catch the source of human movement. At a distance of 2.5 meters below and 60 degrees could not catch the source of human movement. Otherwise at a distance more than 2.5 meters human movement can not be captured by the PIR sensor. At the RFID trial data obtained that the card can be read by an RFID reader within a maximum of 3 cm, with no barrier between the RFID reader and the card. The data condition also occurs when a thick paper is placed between the card and RFID reader as a barrier. While at the moment given the barrier is made from plastic the card can be read at a distance of 1 cm maximum. Keywords: Arduino, ATmega2560, Passive Infra Red (PIR), Radio Frequency Identifier (RFID), Security system.
MODULUS ELASTISITAS BAMBU BETUNG DENGAN VARIABEL PANJANG Rambu Ririnsia Harra Hau; Masturi Masturi; Ian Yulianti; Salvo Kahumbu Hau; Soleman Dappa Talu
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (711.76 KB) | DOI: 10.21009/0305020108

Abstract

The main issues that were examined in this study is the modulus of elasticity bamboo betung with variable length. The purpose of this study was to measure the modulus of elasticity on bamboo betung with variable. Modulus of elasticity in bamboo shows the flexibility for using in a various fields. In this study the bamboo is made into small girders with a uniform thickness and width are respectively 0.8cm and 1.5cm. The length of the bamboo that is used in this study are the 50cm, 60cm, 70cm, 80cm, 90 cm, 100cm. To determine the elasticity of the bamboo it is provided with a load in the middle position. From the research results obtained showing the longer bamboo the greater flexibility gained linearly elastic modulus is 1.0122E+10N/m2. Keywords: bamboo, girder, modulus of elasticity.
KALIBRASI SENSOR ULTRASONIK HC-SR04 SEBAGAI SENSOR PENDETEKSI JARAK PADA PROTOTIPE SISTEM PERINGATAN DINI BENCANA BANJIR Martalia Andayani; Widyaningrum Indrasari; Bambang. H. Iswanto
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (450.412 KB) | DOI: 10.21009/0305020109

Abstract

The water level detection sensor is a major component on flood early warning system. HC-SR04 Ultrasonic Sensor is usually used as a proximity sensor in a flood early warning system. The accuracy of the sensor is essential to support the effectiveness of a system. In this research, the calibration of HC-SR04 ultrasonic sensor using arduino microcontroller, which is it will be used on the prototype early warning system for floods. Calibration is done by taking reference to the warning status I, II, III, and IV of the Katulampa dam. The results showed that both sensor calibration can work well in the range of 14-250 cm, with a maximum relative error of 4.3%. The smallest change in distance that can be detected by the sensor by 1 cm with a maximum relative error of 0.91%. With the errors obtained, it can be said that the sensor is fit as a detector of the water level in flood early warning system prototype in 1:5 scale. Keywords: Ultrasonic Sensor, Arduino, Warning Status.
PEMBUATAN ALBUM WARNA DENGAN MENGGUNAKAN SENSOR WARNA JENIS TCS230 Nenni Mona Aruan; Dwika Andjani; Egi Yuliora
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (787.47 KB) | DOI: 10.21009/0305020110

Abstract

This study used TCS 230 as color sensor to create colors’ album by identified output frequency of TCS 230 and measured RGB value for each color. TCS 230 converted light to electric signal by wave frequency. By using colored paper and facing to TCS 230, the LabVIEW presented its RGB value. From measurements taken, it appears that the sensor have been able to read the color, not just the primary colors (RGB) but also its derivatives. Sensors indicate that despite differences derived by naked eye color and RGB composition has only minor differences, the fixed sensor is capable of capturing the difference even though there are still errors. The amount of the average error for the color red and its derivatives is 28.0336%, while the average error in the measurement of derivatives and their blue color is 38.96% and the average error in blue and derivatives amounted to 32.99103%. Keywords:RGB,TCS 230, labVIEW, colors’ album.
OPTIMASI SUDUT KEMIRINGAN PANEL SURYA PADA PROTOTIPE SISTEM PENJEJAK MATAHARI AKTIF S. Tamimi; W. Indrasari; B. H. Iswanto
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (658.605 KB) | DOI: 10.21009/0305020111

Abstract

The main problem on solar energy is instability power which generated by the solar panels, because it depends on the sunlight intensity which accepted by the solar panels. The intensity of sunlight received by the solar panels can be maximized by installing solar panels with a right angle so it will be obtained the maximum output power. This study has been carried out optimization angle of the solar panels that will be used on the active prototype solar tracking system. The optimization is taking the theta (θ) angle on the x negative axis by using the angle 0ᵒ, 30ᵒ, 45ᵒ and 60ᵒ. The results showed that the average ouput power of the solar panels began to decline at 45ᵒ. To find the best angle we tried to set the optimization at 10o, 20o, 25o, and 40o. Based on these studies an maximum average power output is 73.17mW at the angle of 25o. Key words: solar panels, sunlight intensity, tilt angle, active solar tracker.
STUDI AWAL DATA LOGGER SENSOR ALIRAN FLUIDA BERBASIS MIKROKONTROLER ATMEGA 328 (ARDUINO UNO) Ulfah Zuhaeriah; Iwan Sugihartono; Bernadus Herdi Sirenden
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (612.096 KB) | DOI: 10.21009/0305020112

Abstract

Data logger is a system that can record and save the data continously. A data logger needs controlling system to operate it. One of controlling systems that can be used is Atmega 328 microcontroller (arduino uno). The aim of this research is to build a data logger system based arduino uno which be able reading pulse width data. The pulse width data is output data from RF pickoff sensor. The function of this sensor is to catch magnetic signal from flowmeter turbin. The data logger system is built by Python language to process data on Personal Computer (PC). On this data logger system, arduino will do serial communication using python. The result indicates the pulse width value is below 500 μs. Keywords: Data Logger, Atmega 328 microcontroller, RF Pickoff Sensor, Pulse Width.
PROTOTIPE SISTEM PENGUKUR KUALITAS TEGANGAN JALA-JALA LISTRIK PLN Wisnu Djatmiko
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (646.304 KB) | DOI: 10.21009/0305020113

Abstract

A prototype measuring system voltage quality of the power line based Arduino Uno is proposed to be able to measure and display the VMAX, VEFF, and Frequency using LCD, and realized by 4 sub-system: (1) full-wave rectifier using a diode bridge with a load resistor and pasif low-pass filter to generate VDC; (2) full-wave rectifier using a diode bridge with a load resistor to generate pulses waves of power line; (3) LCD systems board based on IC HD44780 LCD controller; and (4) Board Arduino Uno R3 which serves to calculate and display the value VMAX, VRMS, and the frequency of the power line to LCD. The prototype system has been created and tested can measure voltage of power line in Faculty of Engineering, State University of Jakarta with a value VMAX = 383 Volt, VRMS = 203 Volt, and a frequency of 50Hz is displayed on the LCD and has been compared by using a Digital Multi Meter Sanwa CD800a and PC-Oscilloscope Instrustar ISD205B with an error rate below 1%. Keywords: Line power quality measuring system based Arduino Uno, PLN line voltage parameters, Arduino Uno Application.
ANALISIS AKUSTIK ALAT MUSIK REBANA Yeni Purwiyantini; Mahardika Prasetya Aji; Sulhadi Sulhadi
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (746.441 KB) | DOI: 10.21009/0305020114

Abstract

Rebana/tambourine is a traditional musical instrument which is consist of many kinds. Rebana/tambourine was designed manually and received by the manufacturer with a sense of spirit and their own feelings based on their experiences. Human’s sense of hearing can distinguish between high and low tones, but cannot know surely what kind of tone was heard by them. It is very important for a musician to know whether the instrument is already generating correct tones. Because of that, this research was conducted to analyzed the characteristics of sunds frequency in tambourine/rebana. Tambourine/rebana is traditional musical instrument that do not have a standard tone yet as other musical instruments. Each tambourine generated has a difference in each of her tuning. So, it is hopefully that results of this research can be used to decide the standard of tambourine/rebana musical instrument. This research was conducted used software based on android that is android mobile phones. The android mobile phones has been equipped with an android device audio frequency counter which can directly display the value of the frequency of the sound of tambourines observed. By charging every area constantly, can be obtained the resonance frequency value of tambourine directly on the audio frequency counter column. average resonance frequency obtained from this research to tambourine successively from keplak, hadroh and bass is 750-1251 Hz, 681-1189 Hz, 630-1084 Hz, 503- 736 Hz, 270-448 Hz, 227,5-382 Hz, 146-332 Hz, 145-283 Hz. Keywords: Acoustic, tambourine.

Page 6 of 98 | Total Record : 977