cover
Contact Name
Nevada J.M,Nanulaitta
Contact Email
rio_nevada@yahoo.co.id
Phone
+6281248916219
Journal Mail Official
rio_nevada@yahoo.co.id
Editorial Address
Jl. Ir. M. Putuhena, Rumah Tiga, Kec. Tlk. Ambon, Kota Ambon, Maluku 97234
Location
Kota ambon,
Maluku
INDONESIA
Journal Mechanical Engineering
ISSN : -     EISSN : 29884977     DOI : https://doi.org/10.31959
Core Subject : Engineering,
Manufaktur, Perawatan, Otomotif, Teknik Produksi Migas dan Teknologi Rekayasa Sistem Mekanikal Migas
Articles 20 Documents
Search results for , issue "Vol. 1 No. 3 (2023): Desember" : 20 Documents clear
PENGARUH VARIASI KETINGGIAN STICK OUT PENGELASAN GMAW DAN VARIASI SUDUT SAMBUNGAN PADA KAMPUH ½ V BAJA KARBON SEDANG TERHADAP SIFAT MEKANIS Julian Salakory; Graciadiana I. Huka; Nevada J. M. Nanulaitta; Annafiyah Annafiyah; Ratna Ayu Pawestri Kusuma Dewi
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2095

Abstract

Abstrak Pengelasan merupakan suatu proses penyambungan antara kedua benda logam dengan cara melelehkan atau meleburkan sebagian dari logam tersebut. Salah satu jenis pengelasan yang ada di Indonesia yaitu pengelasan GMAW (Gas Metal Arc Welding). Untuk penggunaan gas pelindung pengelasan GMAW biasanya menggunakan gas Argon sebagai pelindung yang di aplikasikan pada bahan karbon sedang. Penelitian ini dilakukan dengan tujuan untuk mengetahui variasi ketinggian stick out pengelasan GMAW dan variasi sudut kampuh ½ V baja karbon sedang terhadap sifat mekanis. Metode yang digunakan yaitu metode kuantitatif dengan menggunakan data primer yakni pengambilan data pada Lab dan data sekunder berupa studi literature. Berdasarkan hasil penelitian, pengujian impak berada pada ketinggian stick out 10 mm dimana 60° kampuh ½ V memiliki kekuatan tertinggi dengan nilai 0,0920 KJ/mm2 dan kekuatan impak terendah dengan nilai 0,0383 KJ/mm2 pada 45° kampuh ½ V . Sedangkan untuk kekuatan bending tertinggi berada pada ketinggian stick out 5 mm dengan sudut kampuh ½ V 45° sebesar 608,33 MPa dan kekuatan bending terendah sebesar 475,00 Mpa pada sudut kampuh ½ V 60°. Kata Kunci : Pengelasan GMAW, Kekuatan Impak, Kekuatan Bending
EVALUASI PENGGUNAAN SUCKER ROD PUMP PADA SUMUR X LAPANGAN KALREZ Nur Fonisa Kabakoran; Gerry Nirmala; Noce.N. Tetelepta
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2096

Abstract

Petroleum is a very important energy source because oil has a very significant role in meeting world energy. So, when producing petroleum, you need to pay close attention, for this reason an evaluation will be carried out so that you can find out the efficiency of the pump and the strength of the well production.  In the Kalrez Bula field there are petroleum production activities using the sucker road pump (SRP) method. Based on research conducted on the Sucker Rod Pump installed using the Inflow Performance Relationship (IPR) approach for well X, the q max price was obtained at 114.3081 bfpd. Meanwhile, the results of the previous well test were 100 bfpd at a pwf of 70,031 psi with a water cut of 80%, where from the results of the evaluation that had been carried out it was concluded that the pump used in well X with type 20-150 RWAC pump insert was still in place. under optimal circumstances.  Keywords: Artificial lift method,  Sucker Rod Pump, IP
Analisis Pengaruh Ketebalan Plat Dan Sisa Umur Pada Tangki “X” Akibat Pelapukan Oleh Uap Air Laut Di PT. Pertamina Patra Niaga Integrated Terminal Wayame Kota Ambon La Hamdan; Noce. N. Tetelepta; Edison Effendi
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2097

Abstract

Every oil and gas equipment in the oil and gas industry must have a lifespan, so it is necessary to monitor its performance and condition. Likewise with the stockpile tank, in operation and long use, it is likely to experience a decrease in performance or can be said to experience depletion so that it has the opportunity to cause danger. Plate thickness and remaining tank life play an important role in overcoming weathering due to exposure to seawater vapor. Therefore, PT Pertamina Patra Niaga Integrated Terminal Wayame Ambon City needs to regularly monitor the thickness of the tank plate and perform proper maintenance according to the remaining life of the tank. This aims to maintain the reliability and safety of the "X" tank and avoid greater losses.  Keywords: Oil and Gas Industry, Tank, Plate
Pengaruh Temperature Tempering Terhadap Kekerasan Pada Baja Karbon Sedang Hasil Pengelasan FCAW (Flux-Cored Arc Welding) Clara Sekeroney; Nevada. J.M Nanulaita; Frederick Dematacco; Mohammad Anas Fikri; Ike Dayi Febriana
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2098

Abstract

Carbon steel is a type of alloy steel consisting of various elements, especially iron (Fe) and carbon (C). In general, the properties of steel are affected by the percentage of carbon and the microstructure of steel which is affected by steel composition and heat treatment. The welding process can change the structure and composition of steel. The safety of weld results can be carried out after welding using a heat treatment process. This tempering aims to obtain better and desired mechanical properties. Tempering is carried out using temperatures of 200⁰C, 250⁰C and 300⁰C with cooling using air media and mechanical testing will be carried out.The results of this research showed that tempering temperature had an effect on the hardness value of medium carbon steel resulting from FCAW welding. The hardness value at a temperature of 200℃ was 54.75, a temperature of 250℃ was 53.00 and a temperature of 300℃ was 52.04. The higher the temperature, the lower the hardness value and conversely, the lower the tempering temperature, the higher the hardness value.Keywords: Welding, Tempering, Hardness
Analisa Pengaruh Waktu Penahanan (Holding Time) Pada Proses Tempering Terhadap Sifat Mekanis Baja Karbon Menengah Hasil Pengelasan Fcaw (Flux Core Arc Welding) Rey Joy Toding Padang; Nevada. J.M Nanulaita; Cley Talkua; Agustinus O. Lopuhaa; Faizatur Rohmah
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2099

Abstract

FCAW (Flux Core Arc Welding) welding is a type of welding process or joining metal materials that uses a heat source from electrical energy which is converted or converted into heat energy. a roll and uses gas as a protector for the weld metal which melts during the welding process. The content of medium carbon steel is 0.3%C - 0.6%C. This carbon steel has advantages compared to low carbon steel, medium carbon steel has stronger mechanical properties with a higher level of hardness than low carbon steel. . Before and after welding carbon steel materials, material testing will be carried out. With this test, it is hoped that the hardness and bending strength of the material will be known. The method used is a quantitative method including experimental research. With a plate thickness of 5mm, a variation of the V seam angle with an angle of 45° with a depth of 2.5mm. Using a stickout height of 5mm by varying the holding time, namely 30 minutes, 60 minutes, 90 minutes for FCAW welding  Keywords: Carbon steel, FCAW (Flux Core Arc Welding), Holding Time, Hardness Test, Bending Test
Penggunaan Saringan Sebagai Alat Untuk Membantu Mengurangi Kadar Merkuri Yang Tercemar Di Desa Debowae Kecamatan Waelata Kabupaten Buru Provinsi Maluku Alfiansa Umasugi; Erwin. B. Pattykayhattu; M. Said Karyani; Amin Jakfar
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2100

Abstract

Gold mining activities on Buru Island legally or illegally cause water at several coordinate points to be contaminated with heavy metal types of mercury (Hg). Knowing the level of mercury in water is important to determine whether or not water can be consumed. This study aims to determine the level of mercury spread and how to overcome environmental damage due to mercury in water using eucalyptus charcoal. The method used in this study is quantitative by collecting data by observation, interviews, and literature studies. The variable in the study was filtering as a tool to reduce polluted mercury levels. The results of this study were carried out at 3 coordinates and 2 of the 3 coordinates showed a decrease in mercury levels, namely in the coodninat of the father's house, sub-district and village hall successively decreased by 18 μg / L and 2 μg / L. From the results it can be concluded that the level of mercury levels does not exceed the Quality standard figures placed according to the Ministry of Environment and Forestry No.Kep 51 of 2004 and eucalyptus charcoal can reduce mercury levels deposited in water. Based on the results of the research conducted, it turns out that there are still many shortcomings using this method. For future researchers who want to conduct similar research, in order to complement by answering the shortcomings of this study. Keywords: mercury, eucalyptus, filter
Analisis Ketebalan Dinding Pelat Dan Sisa Umur Pada Tangki 11 – 15000kl Di PT. Pertamina Patra Niaga Integrated Terminal Wayame Kota Ambon Arun setiawan; Eka R. M. A. P. Lilipaly; Edison Effendi; Berthy Pelasula
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2102

Abstract

Abstrak Tangki penimbun (storage tank) merupakan salah satu peralatan yang sangat vital pada proses produksi industri perminyakan yang berfungi sebagai tempat penyimpanan dan penimbunan bahan cair, baik berupa minyak mentah, produk BBM, hasil minyak olahan, maupun bahan-bahan kimia lainnya. Korosi merupakan salah satu hal yang menjadi penghalang dalam sebuah proses penyimpanan terlebih lagi dalam fluida cair. Metode yang digunakan dalam pembahasan diawali dengan studi literatur dari berbagai referensi dan penelitian sebelumnya, kemudian pengambilan data lapangan dan kemudian dianalisa.. Dari hasil pengukuran yang diambil pada bulan september 2023, untuk kondisi Tangki 11-15000KL masih bagus ditandai dengan ketebalan course 1-8 masih diatas batas minimum yang sudah ditentukan. Untuk course 1 Tact sebesar 18,77 mm dengan Tmin sebesar 13,22 mm dengan laju korosi sebesar 0,15 mm/tahun dan sisa umur sebesar 37 tahun. Untuk course 2 Tact sebesar 15,84 mm dengan Tmin sebesar 11,81 mm dengan laju korosi sebesar 0,145 mm/tahun dan sisa umur sebesar 27 tahun. Untuk course 3 Tact sebesar 15,06 mm dengan Tmin sebesar 9,45 mm dengan laju korosi sebesar 0,07 mm/tahun dan sisa umur sebesar 80 tahun. Untuk course 4 Tact sebesar 13,17 mm dengan Tmin sebesar 8,17 mm dengan laju korosi sebesar 0,06 mm/tahun dan sisa umur sebesar 83 tahun. Untuk course 5 Tact sebesar 10,23 mm dengan Tmin sebesar 6,89 mm dengan laju korosi sebesar 0,07 mm/tahun dan sisa umur sebesar 47 tahun. Untuk course 6 Tact sebesar 9,55 mm dengan Tmin sebesar 5,61 mm dengan laju korosi sebesar 0,08 mm/tahun dan sisa umur sebesar 60 tahun .Untuk course 7 Tact sebesar 9,26 mm dengan Tmin sebesar 4,33 mm dengan laju korosi sebesar 0,08 mm/tahun dan sisa umur sebesar 63 tahun. Untuk course 8 Tact sebesar 9,50 mm dengan Tmin sebesar 2,54 mm dengan laju korosi sebesar 0,08 mm/tahun dan sisa umur sebesar 84 tahun Dapat disimpulkan kondisi Tangki 11-15000KL masih dalam kondisi baik. Kata kunci: Tangki timbun,minyak,laju korosi,sisa umur tangki,ketebalan tangki
Pengaruh Variasi Arus Pengelasan Gas Metal Arc Welding (GWAM) Terhadap Sifat Mekanis Pada Sifat Seamless Gracia Irene Huka; Leslie. S. Loppies; Josef Matheus; Auliana Diah Wilujeng; Abdul Hamid
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2116

Abstract

GMAW welding is a metal joining process with a melting process with the addition of a coil of wire in the form of electrodes and protective gas. Seamlees pipe, also known as seamless pipe, is an iron pipe without a connection. This study aims to produce data from the results of bending and impact testing on seamlees pipes by varying the welding current with a current of 21.5 volts, 22.5 volts, and 23.5 volts in GMAW welding. After the seamless pipe is welded, impact and bending tests are carried out on the seamlees pipe. From the bending/bending strength test, the highest flexural strength occurred at a current of 21.5 and 22.5 volts, while the lowest flexural strength occurred at a current of 23.5 volts. From the impact test, the highest strength occurred at 21.5 and 22.5 volts and the lowest was at 23.5 volts.  Keywords: Seamlees pipe, GMAW welder, Bending Strength, Impact Strength.  
PENGARUH VARIASI SUDUT PENGELASAN KAMPUH V DAN KETINGGIAN ELEKTRIKAL STICK OUT PENGELASAN GMAW TERHADAP SIFAT MEKANIS BAJA ST-42 Fredrik Demataco; Nevada. J.M Nanulaita; Lukman Hadiwijaya; Ratna Ayu Pawestri Kusuma Dewi
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2120

Abstract

GMAW (Gas Metal Arc Welding), which is a solid or tubular welding electrode that is fed continuously mechanically from a roll of electrode wire inside the welding machine. The electrode is fed via a gun or torch by maintaining the height of the arc formed between the tip of the electrode wire and the material being welded or the base metal. GMAW (Gas Metal Arc Welding) is MAG (Metal Active Gas) and MIG (Metal Inert Gas) welding which is very efficient and fast in the process.Low carbon steel contains less than 0.3% carbon in the carbon steel mixture. Low carbon steel cannot be hardened because the carbon content is not enough to form a martensite structure. Welded joints are material or plate joints that are used for the welding process with the aim of getting maximum penetration from the joint.In this research, we are looking at the effect of the GMAW (Gas Metal Arc Welding) welding process with MIG (Metal Inert Gas) type on ST-42 steel by varying the V seam angle with a stick out height of 5 mm on the mechanical properties in the HAZ area.The hardness value before the welding process at an angle of 15 is in the HAZ area of 30.03 HRD for corners 30 and 45 is 32.51 HRD and 33.98 HRD, while for the impact strength at an angle of 15 is 0.2725 J/mm2, an angle of 30  and 45 namely 0.2439 J/mm2 and 0.2320 J/mm2 Keywords: Welding, HAZ (Heat Affected Zone), Impact Strength, Hardness
Pengaruh Variasi Persentase Hardener pada Campuran Clear Coat Terhadap Kekerasan Cat Pada Pengecatan Body Kendaraan Hermon Latumaerissa; Nevada. J.M Nanulaita; Roy R Lekatompessy; Laily Ulfiyah
Journal Mechanical Engineering Vol. 1 No. 3 (2023): Desember
Publisher : Jurusan Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31959/jme.v1i3.2121

Abstract

Painting is a process of applying paint in liquid form to an object, to create a thin layer which then creates a hard layer or layer of paint. The function of painting itself is to give a layer to an object so that the object's lifespan can be longer. Attachment of paint to the surface can be done in many ways, wiping, smearing, brushing, spraying, dipping or in other ways. Attachment of paint by spraying is the paint attachment that is most often found in automotive painting workshops. Apart from that, attaching paint by spraying is easier in adjusting the area where painting will be carried out, the results are also good if done correctly. The quality of good painting results is influenced by many factors such as skills, materials used, etc., while determining good painting results is based on several factors, such as surface roughness, gloss power, etc. The hardness of the painting results is also greatly influenced by the percentage of hardener mixture in the paint mixture. The paint in question here is color paint (top coat). This research is to determine the best percentage of clearcoat in the painting process by testing the hardness of the painting results. The results obtained by varying the percentage of the mixture in the best clearcoat are in the percentage variations of 100 (Base): 55 (Hardener) + Thiner or Solvent (10% of Base) is 83.49 H, 100 (Base): 55 (Hardener) + Thiner or Solven (10% of Base) is 82.99 H, 100 (Base) : 45 (Hardener) + Thiner or Solven (10% from Base) is 82.51 H and the lowest is the variation 100 (Base): 60 (Hardener) + Thiner or Solvent (10% of Base) namely 79.57 H. Keywords: Painting, Clearcoat, Hardener and Paint hardness

Page 1 of 2 | Total Record : 20