cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota surabaya,
Jawa timur
INDONESIA
Teknika
ISSN : -     EISSN : -     DOI : -
Core Subject : Engineering,
Arjuna Subject : -
Articles 9 Documents
Search results for , issue " Vol 7, No 2 (2006)" : 9 Documents clear
Pemilihan Jaringan Komunikasi Remote Area Rig Onshore Dan Offshore Edy Sulistiyo,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Perkembangan teknologi internet yang sangat pesat mendorong ke arah konvergensi dengan teknologi komunikasi lainnya. Standarisasi protokol komunikasi pada teknologi VoIP seperti H.323 telah memungkinkan komunikasi terintegrasi dengan jaringan komunikasi lainnya seperti PSTN. Jaringan komunikasi yang telah luas tergelar di Indonesia adalah jaringan PSTN yang dikelola oleh PT Telkom. Untuk percangan jaringan tersebut perlu ditentukan posisi Network Operation  Center(NOC) , Point Of Presence (POP), Router , Gateway maupun pembangunan link antar kota – kota yang strategis dan efisien. Dalam perancangan jaringan VoIP, yang di tekankan kali ini adalah masalah delay dan Bandwidth. Delay didefiniskan sebagai waktu yang dibutuhkan untuk mengirimkan data dari sumber (pengirim) ke tujuan (penerima), sedangkan bandwidth adalah kecepatan maksimum yang dapat digunakan untuk melakukan transmisi data antar komputer pada jaringan IP atau internet. Teknologi konvensional menggunakan sistem telekomunikasi yang sangat boros bandwith di sisi perangkat telekomunikasi. Dari sisi data sebenarnya  relatif sama  artinya tidak terlalu jauh bedanya teknologi yang lampau dipakai dengan sekarang. Hanya di sisi penggunaan sarana telekomunikasi yang memang bisa dikatakan mengalami revolusi yang cukup berarti yaitu dengan menggunakan  teknologi yang akhir-akhir ini tengah booming di masyarakat, yaitu apa yang dinamakan teknologi VoIP (Voice over IP). VoIP ini bisa lebih menghemat bandwith karena menggunakan komprosi suara. Bisa dibayangkan bahwa jika kita menggunakan teknologi lama maka konsumsi bandwith bisa mencapai 64 kbps, jika menggunakan teknologi Voip hanya 32 Kbps maksimum. Untuk memperlancar kegiatan operasional digunakan beberapa sistem komunikasi. Tetapi   yang paling penting adalah komunikasi keluar pulau Pagerungan, karena Pagerungan tidak bisa terjangkau oleh sistem komunikasi biasa, contohnya hand phone sehingga untuk berkomunikasi dengan luar Pagerungan digunakan komunikasi satelit yang menunjang untuk komunikasi data, voice, kendali, dan juga pengawasan. Fast development of internet technology has made convergence of another communication technology. Standardization on communication technology of VoIP such as H.323 has made possibility in integrating with another communication network such as PSTN.  PSTN is the widest communication network in Indonesia is held by PT Telkom. To design the network it is needed the position of Network Operation Centre (NOC), point of  Presence (POP), Router , Gateway and also needed to construct the effective and`efficient link among strategic cities. The VoIP design emphasizes on delay and bandwidth factor. Delay is defined as the time needed for sending data from transmitter to receiver. Bandwidth is the maximum speed of data transmission among computer in IP or internet network. Conventional communication technology use inefficient bandwidth of telecommunication devices. From data transmission point of view, there are no significant difference between conventional and`modern communication technology. The new breaktroughon communication technology is the used of VoIP technology. VoIP technology has superiority in bandwidth saving because of sound compression. Because of its capability VoIP can safe the bandwidth until 59% from 64kbps to 32 kbps. For supporting operational activities, it is used some communication system, but the most important is communication system outside of Pagerungan island because on that area cannot be covered by conventional communication system such as handphone, so it is needed satellite communication system for handling data communication voice, control, and monitoring.
Analisis Sistem Pengendalian Antisurge Kompresor Menggunakan Metode Ruang Keadaan (State Space) Puput Wanarti Rusimamto,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Salah satu bentuk kondisi operasi yang tidak stabil pada kompresor adalah kondisi yang disebut surge. Untuk mencegah terjadinya surging, yang disebabkan karena rendahnya laju aliran pada suction kompresor, maka digunakan suatu sistem kontrol yang mengontrol pembalikan sebagian aliran dari discharge ke suction. Hasil perancangan dengan metode Ziegler-Nichols memberikan algoritma pengendalian dengan memberikan penampilan dinamik sistem yang diinginkan, dengan waktu settling 9,11 detik, waktu tunda 1,25 detik, waktu naik 1,82 detik, waktu puncak 2,67 detik dan offset keadaan mantap 2%. Analisa ruang keadaan memperlihatkan kriteria keadaan sistem yang diinginkan yaitu stabil, terkendali dan teramati. One of condition unstable of compressor operation is a condition which called surge. To avoid happening surge condition caused  low flow rate of suction compressor, so it was used a control system controlling reverse of part of flow from discharge to suction. The result of design by Ziegler-Nichols method give control algorithm with desired performance of dynamic system, settling time 9.11 second, delay time 1.25 second, rise time 1.82 second, peak time 2.67 second and steady state  offset 2%. State space analysis show fulfilled criterion of system condition as stable, controllable and observable.
Desain VHDL Sistem Pengirim Data Serial Asinkron 8 Bit Titiek Suheta, ; Arief Budijanto,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Dalam paper ini melaporkan hasil perancangan sistem pengirim data serial asinkron 8 bit yang dibangun dari beberapa blok rangkaiandigital yaitu rangkaian control yang merupakan rangkaian kombinasional, rangkaian counter, register dan multiplekser. Pada perancangan sistem ini menggunakan metoda Alogorithmic State Machine (ASM) sebagai tahapan pertama, kemudian merepresentasikan dalam bentuk table keadaan. Langkah berikut melakukakan verifikasi dengan VHDL tools dari Altera Maxplus 9.5. Hasil simulasi yang diperlihatkan pada gambar 8. dan gambar 9. sudah sesuai dengan rancangan menggunakan ASM.   In this paper, reported the result of the design of eight bit asinkron serial data sender system is built from digital connection is the control conection or combination connection, counter connection, register and multiplexer.In this design system, uses ASM method as the first step is doing verification with VHDL tools from altera maxplus 9.5. The result of simulation is shown in picture 8 and 9 is suitable with the design using ASM.
Studi Eksperimen Campuran Premium TT Dan Toluena (C7H8) Terhadap Daya, Konsumsi Bahan Bakar, Dan Emisi Gas Buang Pada Sepeda Motor Honda Supra Fit 100cc Luqman Syarief(, ; Aisyah Endah Palupi(2),
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

AbstrakPenambahan aditif dilakukan untuk memperbaiki kualitas BBM baik dari sisi performa maupun ekonomisnya, sedangkan sifat utama BBM yang harus dimiliki untuk kinerja optimal mesin adalah dapat memberikan campuran bahan bakar-udara dalam perbandingan yang tepat dan memberikan pembakaran secara normal pada saat yang tepat di dalam siklusnya. Sebagai bahan aditif, toluena mempunyai sensitivitas yang cukup rendah untuk membuatnya menjadi bahan bakar yang baik bagi mesin dengan beban yang berat. Toluena juga mempunyai specific gravity lebih besar dari bensin yang dapat mengurangi Sfc.Hasil penelitian secara eksperimen, menunjukkan campuran toluena pada premium TT dapat meningkatkan daya efektif (Ne), menurunkan konsumsi bahan bakar spesifik (Sfc), dan menurunkan kadar emisi (CO dan HC). Additive addition is conducted to improve the quality of fuel from both the performance and economical side, while the main charateristic which fuel must own for the optimal machine performance is to be able to give the substances mixture between fuel-air in accurate composition and give the combustion normally in an appropriate time in its cycle. As an additive, toluena have such kind of sensitivity which is low enough to make fuel which is good for the heavy burden machines. Toluena also has specific gravity which is bigger than gasoline which can lessen the Sfc.The result of this experiment shows that toluena and premium TT mixture can improve the actual horsepower (Ne), degrade specific fuel consumption (Sfc), and degrade the emission rate (CO and HC).
Pengaruh Penggunaan Catalytic Converter Tembaga Berlapis Mangan Terhadap Kadar Polutan Gas Buang Motor Bensin Empat Langkah Warju(, ; Djoko Sungkono(2),
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

One of the efforts to decrease exhaust gas emission from four stroke gasoline engine is using cuprum (Cu) coated mangan (Mn) as active metal catalyst to reduce CO, HC and NOx emission. It is placed in exhaust system that is called catalytic converter.The experiment was carried out at Fuel and Internal Combustion Engine Laboratory Mechanical Engineering Departement ITS. In this experiment Honda Karisma X 125D engine was used. The test method is done by velocity gradient at full load (full open throttle valve). The test was carried out by comparing standard engine experiment and engine experiment with catalytic converter on exhaust system. The type of the test is desk test. Data analysis is done by using descriptive methods. The analysis shows that cuprum (Cu) coated mangan (Mn) as catalytic converter with 110 gr Cu + 90 gr Mn catalyst mass decreases vehicle emission that the greatest CO emission decrease at A/F 15 or exhaust gas temperature 273-340°C is up to 96,36%.
Pengaruh Penggunaan Catalytic Converter Kuningan (Cu-Zn) Terhadap Konsentrasi Polutan Gas Buang Motor Bensin Empat Langkah Andi Sanata, ; Djoko Sungkono,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

One alternative for reduction pollutant is treating after combustion syatem. Placing catalytic converter in exhaust gas system, pollutant (CO and HC) can be decrease by chemical process such as oxidation and reduction.The experiment is being done at Internal Combustion Engine Laboratory Mechanical Engineering Department FTI-ITS. In this experiment Honda Karisma 125 cc motorcycle engine was used. The test result are comparing between standart engine experiment and engine experiment with catalytic converter on exhaust system.The analysis shows that brass (Cu-Zn) as catalytic converter with 160 gr catalyst mass treatment decreases CO pollutant up to 79,92% and HC pollutant up to 62,16% from standar engine treatment.
Pengaruh Tyre Soil Terhadap Daya Dukung Pondasi Dangkal, Pada Tanah Ekspansif Padat Dengan Pembasahan Menggunakan Bentuk Permodelan Di Laboratorium Nur Andajani,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

One of way to prevent foundation damage of expansive soil are by repairing the expansive soil using tyre soil, because it had been proven that tyre soil can function as building strengthen structure. It is important to do a certain research to exercise the effect of tyre soil of the bearing capacity  of shallow foundation. Expectedly,  result study of the using of tyre soil can strengthen bearing capacity and  the descent of the settlement.This study will be done using model experiment in the laboratory. Sample study  is the Citraland ekspansif soil with LL = 198% and given 15% fly ash. The study will be done by condition optimum of water content ( Wopt ) from proctor standard result, then will be wetting in 3 and 5 days. Each of soil type will be given small tyre soil, large soil tyre and without tyre soil. Total sample will be tested are 6 sample, comprise of 3 samples will be wetting in 3 days and 3 samples will be wetting in 5 days.The result shows that by adding tyre soil material influence of bearing capacity foundation increase, and the of settlement may decrease. For the experiment sample wetting for 3 days, treated the bearing capacity increase as 30 % for the sample added by small tyre soil and the sample added by large tyre soil will increase as 56.67 %. For the experiment sample wetting for 5 days,  the bearing capacity will increase as 33.33 % for sample by small tyre soil, and   added by larger tyre soil will increase as 56.86 %.
Pemanfaatan Abu Sekam Sebagai Bahan Penyusun Spesi Robby Tamba,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Semen portland sebagai pengikat hidrolis berdasarkan penelitian sebelumnya dapat digantikan dengan pengikat yang lain, seperti abu sekam padi (ASP), bila dicampur dengan bahan tertentu. Berdasarkan hal tersebut abu sekam padi dapat dimanfaatkan sebagai campuran spesi. Pada penelitian ini akan dicoba sejauh mana keefektifan spesi yang menggunakan kompasisi campuran 0,3 PC dengan dicampur 0,7 ASP, ditinjau dari kuat tekannya.Penelitian ini dilakukan dengan membuat kubus spesi dengan perlakuan pemberian bahan pengikat Abu Sekan Padi (ASP). Komposisi spesi yang diteliti adalah 1PC : 2PS, 1PC : 3PS, 1PC : 4PS sebagai pembanding. Sebagai uji coba dari ketiga komposisi tersebut untuk bagian PC, disubtitusi Asp sebesar 70%. Benda uji kubus masing masing kelompok dibuat 20 buah benda uji dan diuji kuat tekannya.Dari hasil pengujian menunjukkan bahwa penambahan ASP sebesar 70% dari berat semen kurang efektif dan menghasilkan kuat tekan yang jauh lebih rendah dibandingkan dengan kuat tekan spesi tanpa menggunakan Asp. Penurunannya melebihi 75% dibandingkan dengan tanpa penambahan Asp. Portland cement as hydraulic binder based on previous research can be replaced with other binder, as abu sekam padi (ASP), if mixed with specified material. Based on this matter, abu sekam padi can be used as spesi mixing. In this research, an action will be executed to know the effectiffeness of spesi which is used for mixing composition of       0,3 PC with 0,7 ASP, refer on its compressive strength.This research will be conducted by creating spesi cube with a giving treatment of abu sekam padi (ASP) material binder. This research will focus on spesi composition of 1PC : 2PS, 1PC : 3PS, 1PC : 4PS as comparison. As experimental from these three compositon for PC part, ASP distribution is 70%. Cube test material for each group will be made 20 test materials and to be tested for its compressive strength.The result of this research showed that ASP addition for 70% from its cement weight is not effective and resulted lower compressive strength than spesi without ASP. The decreasing is over 75% compare than non ASP addition.
Rencana Tata Tanam Dalam Upaya Hemat Air Di Ji. Jepun UPTD Lenteng Kabupaten Sumenep Indiah Kustini, ; Retno Widorini,
Teknika Vol 7, No 2 (2006)
Publisher : Teknika

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Penelitian ini bertujuan dalam upaya melaksanakan hemat air,  karena tahun demi tahun, kebutuhan air makin bertambah sedang siklus air tetap dan banyak mengalami gangguan alam.  Salah satu tanaman yang  kehidupnya tergantung dari air  adalah tanaman semusim yaitu padi, palawija dan tembakau yang pemberian airnya melalui jaringan irigasi. Sebagai obyek penelitian adalah rencana tata tanam di  jaringan irigasi  Jepun UPTD Lenteng,  Kabupaten Sumenep dengan baku sawah 1396 ha.  1396 ha.  Pola tanam yang ada padi – palawija/tembakau – palawija, dengan tanaman tembakau 40 – 60 % dengan intensitas yang ada 220 %. Metode yang digunakan adalah metode diskriptif kualitatif dengan didukung data sekumder  dan data lapangan   kemudian dianalisis  dengan  teori yang ada kemudian dibuat beberapa alternatip kebutuhan air tanaman padi. Faktor yang mempengaruhi agar memiliki kebutuhan air yang minimum antara lain:   pelaksanaan awal rencana tata tanam, baku sawah dibagi menjadi 3 golongan yang dilaksanakan secara rotasi, penyiapan lahan untuk pembibitan atau yang perlu digenangi dalam 1 bulan hanya 1/20 lahan dan pemberian air pada MK dilaksanakan secara giliran. Hasil penelitian menyatakan bahwa   kebutuhan air tanaman di sawah pada MH/normal setiap ha  0,23 s/d 0,29, minimal 0,20 lt/dt pol , yang sebelum dilapangan (hasil pengamatan) 0,29 s/d 0,35, minimal 0,25 lt/dt.pol  jadi didapat hemat air   0,06 lt/dt.pol. Hemat air 0,06 lt/dt dapat dimanfaatkan.untuk menaikkan intensitas pada musim kemarau  60 % dari  intensitas tanaman  220 % menjadi 280 %  per tahun. The purpose of intend expedient to compare water economical, because year in year to increase water requirement just water circulate constant and experiences earth obstruction.  Any thing vegetation that water is subsistence vegetation season this rice plant, crop and tobacco that water supply from irrigation net work.  The obyek  of the research is to practise agriculture in irrigation net work Jepun UPTD Lenteng Kabupaten  Sumenep with plant areal 1396 ha. Design practise agriculture this one rice-crop/tobacco-crop, with vegetation tobacco 40 – 60 % with intensitas 220 %.The method this research is descriptive qualitative which is supported by numeric data or percentage, that is analisis data space whith theory than artificials net field water requirement. The factor which influence product minimum water requirement are the:  perfumes  to practise agriculture in November, for tree group area rice field which rotasi method, land preparation wich substratum or stagnant water 1 month 1/20 land rice and dry season water supply too rotasi metod. The result of this research is that net field water requirement rainy season  per hectar 0,23 - 0,29 , minimal 0,20 lt/sec/crop, before income data space  0,29 - 0,35 , minimal 0,25 lt/sec/crop, so possible expendient economical water vegetation   0,06 lt/sec. Economical water 0,06 lt/sec, to make possible ascend intensitas dry season  60 % form  intensitas vegetation 220 % up to 280 %  per year

Page 1 of 1 | Total Record : 9