Garuda - Garba Rujukan Digital

Extendable Geoslicer: A New Technique in Collecting Unconsolidated Sediment and Soil Samples Yulianto, Eko; Supriatna, Nandang; Lili, Endang
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.115-122Geoslicer is a field gear for active fault geology studies invented in Japan, in 1997. It was formerly addressed to overcome some difficulties in studying active faults. Lately, it has also been applied for tsunami, geological, liquefaction geology, geo-archaeology, and Quaternary geology in common. Despite evidently effective in those studies, it still bears several disadvantages. Several modifications and developments have been implemented to eliminate these disadvantages. A new type geoslicer was invented as a result, Extendable Geoslicer. This new type geoslicer has been tested and showed good performance in relation with the disadvantages of the old type. Extendable geoslicer is evidently operated more easily, cheaper, handier, and works in all field types.

Advanced Applications of Synthetic Aperture Radar (SAR) Remote Sensing for Detecting Pre- and Syn-eruption Signatures at Mount Sinabung, North Sumatra, Indonesia Saepuloh, Asep; Mirelva, Prima Rizky; Wikantika, Ketut
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.123-140Mount Sinabung was re-activated at August 28th, 2010 after a long repose interval. The early stage of a phreatic eruption was then followed by magmatic eruptions at September 15th, 2013 for years until now. To understand the ground surface changes accompanying the eruption periods, comprehensive analyses of surface and subsurface data are necessary, especially the condition in pre- and syn-eruption periods. This study is raised to identify ground surface and topographical changes before, intra, and after the eruption periods by analyzing the temporal signature of surface roughness, moisture, and deformation derived from Synthetic Aperture Radar (SAR) data. The time series of SAR backscattering intensity were analyzed prior to and after the early eruption periods to know the lateral ground surface changes including estimated lava dome roughness and surface moisture. Meanwhile, the atmospherically corrected Differential Interferometric SAR (D-InSAR) method was also applied to know the vertical topographical changes prior to the eruptions. The atmospheric correction based on modified Referenced Linear Correlation (mRLC) was applied to each D-InSAR pair to exclude the atmospheric phase delay from the deformation signal. The changes of surface moistures on syn-eruptions were estimated by calculating dielectric constant from SAR polarimetric mode following Dubois model. Twenty-one Phased Array type L-band SAR (PALSAR) data on board Advanced Land Observing Satellite (ALOS) and nine Sentinel-1A SAR data were used in this study with the acquisition date between February 2006 and February 2017. For D-InSAR purposes, the ALOS PALSAR data were paired to generate twenty interferograms. Based on the D-InSAR deformation, three times inflation-deflation periods were observed prior to the early eruption at August 28th 2010. The first and second inflation-deflation periods at the end of 2008 and middle 2009 presented migration of magma batches and dike generations in the deep reservoir. The third inflation-deflation periods in the middle of 2010 served as a precursor signal presenting magma feeding to the shallow reservoir. The summit was inflated about 1.4 cm and followed by the eruptions. The deflation of about 2.3 cm indicated the release pressure and temperature in the shallow reservoir after the early eruption at August 28th, 2010. The last inflation-deflation period was also confirmed by the increase of the lava dome roughness size from 5,121 m2 on July to 6,584 m2 on August. The summit then inflated again about 1.1 cm after the first eruption and followed by unrest periods presented by lava dome growth and destruction at September 15th, 2013. The volcanic products including lava and pyroclastics strongly affected the moisture of surface layer. The volcanic products were observed to reduce the surface moisture within syn-eruption periods. The hot materials are presumed responsible for the evaporation of the surface moisture as well.

Sedimentation Process of Rambatan Formation in Larangan Brebes, North Serayu Range, Central Java Astuti, Bernadeta Subandini; Isnaniawardhani, Vijaya; Abdurrokhim, Abdurrokhim; Sudradjat, Adjat
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.141-151Rambatan Formation in the western part of North Serayu Basin, Brebes, Central Java, comprises generally flysch facies of turbidite sediments deposited in a deep marine environment. This formation is equivalent to Merawu Formation found in the eastern part of the basin and deposited in the environment of tidal flat to subtidal. The turbidite sediments were highly controlled by a rapid downward movement taking place continuously during Early to Late Miocene. The variation of the depositional environment has been the object of this research which aims to understand the sedimentation process of Rambatan Formation in this type locality with a modern turbidite approach. Rambatan Formation was deposited in N13-N19, as a deep marine sediment channel, turbidite, and deep marine tidal zone. The sedimentation was affected by gravity flow and contourite. The sediments on N13-N14 were marked by turbidite sediments until Middle N17. The sediment supply increased on Middle N17, as a sediment filler on a channel marked by contourite mud layer (muddy slump) and debris flow, with sources from the north. The increase of sediment supply was followed by an environmental transformation from a deep marine channel into deep marine tidal area. In N19, the sediments were redeposited as turbidite sediment, starting with debris flow in Middle N18.

Exhumation and Tectonomagmatic Processes of the Granitoid Rocks from Sulawesi, Indonesia: Constrain from Petrochemistry and Geothermobarometry Study Maulana, Adi; Imai, Akira; Watanabe, Koichiro; van Leeuwen, Theo; Widodo, Sri; Musri, Musri
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17014/ijog.6.2.153-174

DOI:10.17014/ijog.6.2.153-174Exhumation and tectonomagmatic processes of the granitoid from Sulawesi were discussed using petrochemistry (e.g. petrographic and major element compositions) and geothermobarometry data (mineral chemistry data). Detailed petrographic observations were conducted to determine the mineral composition, texture, and structure of the granitoid rocks, whereas the whole rock composition were determined using XRF method, and the mineral chemistry was analyzed using Electron Microprobe Analyzer (EPMA). The granitoids are classified as calc-alkaline, metaluminous I-type. Pressures of 0.91 to 1.2 kbar and emplacement depths of 3.2 to 4.3 km at temperatures of 677 - 729°C were estimated for Mamasa Pluton. Whereas Masamba Pluton was emplaced at pressures of 2.3 to 2.8 kbar, temperatures of 756 - 774°C, and emplacement depths of 8.2 to 10 km. Moreover, Lalos-Toli and Sony Plutons were emplaced at temperatures of 731 to 736°C and 601 to 609°C, respectively. The pressures varying from 3.1 to 3.3 kbar and 3.2 to 3.4 kbar, equate to an emplacement depth of 11.3 and 11.6 km, respectively. Gorontalo Pluton emplaced at temperatures of 662 - 668°C with the pressure range from 2.6 to 2.7 kbar, is equivalent to 9.3 km deep. Varied oxidation state (ranging from -14 to 19) is inferred from the mineral assemblages, showing a strong association with highly oxidized I-type series granitic rocks. The exhumation rate estimation shows that Mamasa and Masamba Plutons were exhumed respectively at a rate of 0.37 and 1.6 mm/year, whereas Lalos-Toli and Sony Plutons at 1.4 and 2.7 mm/year, respectively. Gorontalo Pluton located in the Northern Sulawesi Province was exhumed at 0.42 mm/year. The rapid exhumation rate of Sony Pluton is attributed to the active vertical movement of Palu-Koro Fault Zone which has been active since Pliocene. It shows that faulting may play an important role in differential exhumation of intrusive bodies in the orogenic belt.

Mineralogical and Geochemical Characterization of Jordanian Olivine and Its Ability to Capture CO2 by Mineralization Process Dwairi, Reyad Al
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.175-183Olivine rich rocks outcrop in Kharazeh area (KHO) and Jurf Eldaraweesh (JDO) Basaltic rocks southern Jordan. KHO and JDO have been characterized for their mineralogical and geochemical properties investigated for their potential use in CO2 capture by mineralization process. The effects of particle size, temperature, and contamination time were examined in the mineralization process. Two grain sizes of olivine for each type were used in capture experiments. The first grain size is the separated size fraction between 1 to 0.7 mm (KHO1 and JDO1), while the second grain size is the separated size fraction between 0.7 to 0.3 mm (KHO2 and JDO2). For the mineralization purpose, a chemical reactor was used to determine the olivine CO2 capture capacity. Thin section studies aided by XRD identification for KHO indicated the presence of olivine crystals as the main mineral with percentage reaches 48% plagioclase, augite, and magnetite. While the mineral content for JDO is (35%) olivine, plagioclase, clinopyroxene, and opaque minerals. Olivine chemical composition results show the high MgO percentage for KHO ranges between 47.5 and 50.13%, while the percentage of MgO varies from 43.6% and 44.6% for JDO. The CO2 mineralization process results were interpreted using percentage removal curves. CO2 capture percentage reaches the highest percentage (48%) using KHO2 and 100o C temperature. In summary, it can be concluded that CO2 can be removed from atmosphere using Jordanian olivine rich rocks.

Facies Associations of Early Cretaceous Arumit Formation and Early to Late Cretaceous Ungar Formation in Vulmali and Ungar Islands, Tanimbar (Indonesia) Fakhruddin, Rakhmat
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17014/ijog.6.2.185-208

DOI:10.17014/ijog.6.2.185-208Cretaceous sediments are among the important petroleum system elements for hydrocarbon exploration in Tanimbar area. However, little is known about their facies associations and depositional environments. Facies association analyses have been carried out in fourteen surface sections. Early Cretaceous Arumit Formation comprises three facies associations: subtidal, intertidal, and supratidal deposits. A progradational open-coast tidal flat depositional environment suggests the deposition of sediments of the Arumit Formation. The presence of tidal rhythmites, mud drapes, and fluid mud in those sediments are diagnostic features of a tide domination process in deposition of this unit. Early to Late Cretaceous Ungar Formation in the studied area consists of four facies associations: intertidal, marine offshore to lower shoreface, upper shoreface, and foreshore deposits. An open-coast wave dominated depositional environment is proposed for deposition of sediments of the Ungar Formation. Wave dominated environments in the coarsening upward interval is represented by hummocky cross stratification, cross-bedded sand and gravel, planar parallel stratification, and low-angle stratified beds.

Characteristics of Arun Carbonate Reservoir and Its Implication To Optimize the Most Potential Gas Resource Zone In Arun Gas Field, Aceh, Indonesia Atmadibrata, Riza; Muslim, Dicky; Hirnawan, R. Febri; Abdurrokhim, Abdurrokhim
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.209-222Since the discovery of major oil and gas reserves in carbonate rocks in the Middle East, carbonate reservoirs became important to the petroleum industry. Carbonate rocks have covered only 20% of the sedimentary rock records. However, carbonate reservoirs hold 50% of the world petroleum reserves. Arun Carbonate Reservoir is one of the biggest proven retrograde gas reservoirs in the world. After more than thirty years of production, Arun Carbonate Reservoir had an initial gas in place of 14.1 TCF residual hydrocarbon gas. The issue makes Arun Carbonate Reservoir became an interest to be studied for the development and production of hydrocarbon in other carbonate reservoirs in Indonesia. One of the fundamental topics to be studied is the characteristics of Arun Carbonate Reservoir itself. The characteristics of carbonate reservoir usually cause a lot of geologic and engineering problems in the development and production of hydrocarbon reserves. This paper aims to identify the characteristics of Arun Carbonate Reservoir and its implication to delineate the potential gas resource zone in the Arun Gas Field, Aceh, Indonesia. The data from sixteen wells have been examined through several multidiscipline studies: geophysics (well logging), geology (facies, lithology and diagenetic analyses), and petrophysics (core analysis). The result of this study shows that Arun Carbonate Reservoir (N5-N8) contains limestone 92%, 5% dolomite, and 3% dolomitic limestone (or other), and petrophysically have 16% porosity and 13.5 md permeability in average. Arun Carbonate Reservoir is divided into four facies (Reef, Near Reef, Inter Reef Lagoon, and Middle Shelf). Of four facies in Arun Carbonate Reservoir, only two facies which can be categorized as productive facies: Reef and Lagoonal Facies. The potential zones of hydrocarbon resources have vertically been documented in Arun Carbonate Reservoir.

Extendable Geoslicer: A New Technique in Collecting Unconsolidated Sediment and Soil Samples Eko Yulianto; Nandang Supriatna; Endang Lili
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.115-122Geoslicer is a field gear for active fault geology studies invented in Japan, in 1997. It was formerly addressed to overcome some difficulties in studying active faults. Lately, it has also been applied for tsunami, geological, liquefaction geology, geo-archaeology, and Quaternary geology in common. Despite evidently effective in those studies, it still bears several disadvantages. Several modifications and developments have been implemented to eliminate these disadvantages. A new type geoslicer was invented as a result, Extendable Geoslicer. This new type geoslicer has been tested and showed good performance in relation with the disadvantages of the old type. Extendable geoslicer is evidently operated more easily, cheaper, handier, and works in all field types.

Advanced Applications of Synthetic Aperture Radar (SAR) Remote Sensing for Detecting Pre- and Syn-eruption Signatures at Mount Sinabung, North Sumatra, Indonesia Asep Saepuloh; Prima Rizky Mirelva; Ketut Wikantika
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.123-140Mount Sinabung was re-activated at August 28th, 2010 after a long repose interval. The early stage of a phreatic eruption was then followed by magmatic eruptions at September 15th, 2013 for years until now. To understand the ground surface changes accompanying the eruption periods, comprehensive analyses of surface and subsurface data are necessary, especially the condition in pre- and syn-eruption periods. This study is raised to identify ground surface and topographical changes before, intra, and after the eruption periods by analyzing the temporal signature of surface roughness, moisture, and deformation derived from Synthetic Aperture Radar (SAR) data. The time series of SAR backscattering intensity were analyzed prior to and after the early eruption periods to know the lateral ground surface changes including estimated lava dome roughness and surface moisture. Meanwhile, the atmospherically corrected Differential Interferometric SAR (D-InSAR) method was also applied to know the vertical topographical changes prior to the eruptions. The atmospheric correction based on modified Referenced Linear Correlation (mRLC) was applied to each D-InSAR pair to exclude the atmospheric phase delay from the deformation signal. The changes of surface moistures on syn-eruptions were estimated by calculating dielectric constant from SAR polarimetric mode following Dubois model. Twenty-one Phased Array type L-band SAR (PALSAR) data on board Advanced Land Observing Satellite (ALOS) and nine Sentinel-1A SAR data were used in this study with the acquisition date between February 2006 and February 2017. For D-InSAR purposes, the ALOS PALSAR data were paired to generate twenty interferograms. Based on the D-InSAR deformation, three times inflation-deflation periods were observed prior to the early eruption at August 28th 2010. The first and second inflation-deflation periods at the end of 2008 and middle 2009 presented migration of magma batches and dike generations in the deep reservoir. The third inflation-deflation periods in the middle of 2010 served as a precursor signal presenting magma feeding to the shallow reservoir. The summit was inflated about 1.4 cm and followed by the eruptions. The deflation of about 2.3 cm indicated the release pressure and temperature in the shallow reservoir after the early eruption at August 28th, 2010. The last inflation-deflation period was also confirmed by the increase of the lava dome roughness size from 5,121 m2 on July to 6,584 m2 on August. The summit then inflated again about 1.1 cm after the first eruption and followed by unrest periods presented by lava dome growth and destruction at September 15th, 2013. The volcanic products including lava and pyroclastics strongly affected the moisture of surface layer. The volcanic products were observed to reduce the surface moisture within syn-eruption periods. The hot materials are presumed responsible for the evaporation of the surface moisture as well.

Sedimentation Process of Rambatan Formation in Larangan Brebes, North Serayu Range, Central Java Bernadeta Subandini Astuti; Vijaya Isnaniawardhani; Abdurrokhim Abdurrokhim; Adjat Sudradjat
Indonesian Journal on Geoscience Vol 6, No 2 (2019)
Publisher : Geological Agency

DOI:10.17014/ijog.6.2.141-151Rambatan Formation in the western part of North Serayu Basin, Brebes, Central Java, comprises generally flysch facies of turbidite sediments deposited in a deep marine environment. This formation is equivalent to Merawu Formation found in the eastern part of the basin and deposited in the environment of tidal flat to subtidal. The turbidite sediments were highly controlled by a rapid downward movement taking place continuously during Early to Late Miocene. The variation of the depositional environment has been the object of this research which aims to understand the sedimentation process of Rambatan Formation in this type locality with a modern turbidite approach. Rambatan Formation was deposited in N13-N19, as a deep marine sediment channel, turbidite, and deep marine tidal zone. The sedimentation was affected by gravity flow and contourite. The sediments on N13-N14 were marked by turbidite sediments until Middle N17. The sediment supply increased on Middle N17, as a sediment filler on a channel marked by contourite mud layer (muddy slump) and debris flow, with sources from the north. The increase of sediment supply was followed by an environmental transformation from a deep marine channel into deep marine tidal area. In N19, the sediments were redeposited as turbidite sediment, starting with debris flow in Middle N18.

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Ivan Ferdian

Contact Email
ivan.ijgbg@gmail.com

Phone
-

Journal Mail Official
ivan.ijgbg@gmail.com

Editorial Address
-

Location
Kota bandung,

Jawa barat

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Ivan Ferdian

Contact Email ivan.ijgbg@gmail.com

Phone -

Journal Mail Official ivan.ijgbg@gmail.com

Editorial Address -

Location Kota bandung, Jawa barat INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Ivan Ferdian

Contact Email
ivan.ijgbg@gmail.com

Phone
-

Journal Mail Official
ivan.ijgbg@gmail.com

Editorial Address
-

Location
Kota bandung,

Jawa barat

INDONESIA