Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Bulletin of Electrical Engineering and Informatics

EEI
Website

Published by IAES Indonesia Section and Partners

ISSN : - EISSN : - DOI : -

Core Subject : Engineering,

Electrical & Electronics Engineering

Arjuna Subject : -

Articles 90 Documents

3 4 5 6 7

Search results for , issue "Vol 8, No 2: June 2019" : 90 Documents clear

Capacitive Electrode Sensor Implanted on a Printed Circuit Board Designed for Continuous Water Level Measurement Abdullahi, Salami Ifedapo; Habaebi, Mohamed Hadi; Malik, Noreha Abdul
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v8i2.1515

Water level sensors are one of the practical ways to get the actual measurement of the depth of a dam or canal. The ease of deployment and easy data acquisition makes them widely used in many fields. Therefore, it will be advantageous to have a miniaturized water level sensor for easier mobility and deployment. A novel method for measuring water level using a Printed Circuit Board has been proposed in this paper. The design stages of circuit sketching, printing of sketch on PCB and etching are discussed for the electrode water level sensor. A signal conditioning circuit is necessary to maintain a steady flow of current from the power source. The fabricated electrode water level sensor was tested based on its capacitive effect while charging up and the amount of current at each electrode finger at the saturation stage. The hardware enablers for this test were the multimeter and LCR meter. Arduino microprocessor was used to test and measure the transient response time for each electrode finger. The transient response sensitivity of the electrode sensor is measured to be 0.0873 millisecond/cm while the resolution of the electrode sensor is 0.1cm over a range of 30cm water level. A multiple correlation of 0.921 was achieved for the water level, measured current and measured capacitance with P-values less than 0.05 indicating strength of the data obtained from the tests conducted. The result showed strong evidence that the electrode water level sensor can be an alternative method of measuring water level.

Investigation on the Mass Sensitivity of Quartz Crystal Microbalance Gas Sensor using Finite Element Simulation Ralib, Aliza Aini Md; Zamri, Nik Nursyahida Bt Nik Mohd; Hazadi, Ahmad Hafiz Faqruddin; Rahim, Rosminazuin Ab; Za’bah, Norfarahidah; Saidin, Norazlina
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v8i2.1521

The increasing global trends in healthcare priorities towards improving the effectiveness of diagnostic procedure by utilizing a non-invasive method which is breath analysis. This will benefit in increasing treatment efficiency and also reducing healthcare costs. Breath is a simple technique where the sample are easily obtained and can be provided immediately. The most popular method that had been used in hospital are urine and blood. Contradict with breath, urine and blood take too much time to analyse the disease and a painful process. The detection technique of breath analysis is done by using electroacoustic wave sensor from piezoelectric substrate. This acoustic wave sensor has been used to detect the changes in the frequency where it will be used to detect the disease. Breath analysis is a technique where it uses an electronic nose (E-nose) as a device. E-nose consist of Quartz Crystal Microbalance (QCM) sensor in order to differentiate odor in human breath. QCM is a sensitive weighing device which have a high efficiency. AT-cut quartz was chosen as the piezoelectric material and aluminum as the electrode. The objective of this paper is to design and simulate a QCM sensor for breath analysis application. Other than that, it also to determine the important key parameters that influence the performance of breath analysis which is sensitivity and resonant frequency. QCM sensor is being simulate by using COMSOL Multiphysics software. This is to evaluate the behavior of QCM sensor in terms of Eigen frequency analysis. The simulated QCM sensor with quartz radius of 166 um resonates at 8.871 MHz. The sensitivity of the sensor is 0.167 MHz/ng after exposed to acetone gas which act as the breath marker for detection of diseases in exhaled breath.Hence, the proposed design can be used as a non-invasive approach for early detection of disease through breath analysis.

Recyclable Waste Separation System Based on Material Classification using Weight and Size of Waste Midi, Nur Shahida; Rahmad, Muhammad Aizat; Yusoff, Siti Hajar; Mohamad, Sarah Yasmin
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v8i2.1523

Insufficient landfills problem had increased the needs to decrease the waste and recycling them. However, despite the efforts done by the government and local authorities on promoting recycling culture by introducing new laws and regulations, the awareness and willingness among the community is still low. One of the possible reasons to this is lack of effort to categorize the waste into the designated category which are paper, glass, plastic and metal. In order to address this problem, it is important to design a system that will ease the process of categorizing the waste. This can be achieve by the automation of the said process. In this work, a system consist of an algorithm and hardware to automatically categorize recyclable waste is proposed. The proposed system are utilizing weight sensor and ultrasonic sensors in order to capture the characteristics of the waste item, which are weight and size so that it can be categorized into paper, glass, plastic and metal. Here, a sytem to automatically separate household waste item is presented by combining an algorithm with a set of hardware consist of minimal number of sensors, conveyer belt and servor motors.

MM-PNEMO: A Mathematical Model to Assess Handoff Delay and Packet Loss Islam, Shayla; Hashim, Aisha Hassan Abdalla; Hasan, Mohammad Kamrul; Razzaque, Md. Abdur
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v8i2.1525

Wireless networks incorporate Mobile Nodes (MNs) that use wireless access networks to communicate. However, the communication among these MNs are not remained stable due to the poor network coverage during inter mobility. Moreover, the wireless nodes are typically small that results in resource-constrained. Thus, it is uphill to use algorithms having giant processing power or memory footprint. Accordingly, it is essential to check schemes consistently to evaluate the performance within the probable application scenario. To do so, numerical analysis could be a notable method to grasp the performance of mobility management schemes as well as the constraint of evolving mobility management solutions specifically for multi-interfaced MR in Proxy NEMO environment. This paper analyzes handoff performance by using a mathematical model of Multihoming-based scheme to support Mobility management in Proxy NEMO (MM-PNEMO) environment. Moreover, a comparative study has been made among the standard Network Mobility Basic Support Protocol (NEMO BSP), Proxy NEMO (PNEMO) and MM-PNEMO scheme respectively. The performance metrics estimated for these schemes are mainly handoff delay and packet loss. This paper also analysed the packet loss ratio and handoff gain as a function of cell radius, number of SMR and velocity respectively. It is apparent that, the MM-PNEMO scheme shows lower packet loss ratio (1%) compared to NEMO-BSP (11%) and P-NEMO (6%).

Energy Efficient Smart Street Light for Smart City using Sensors and Controller Abdullah, Aziera; Yusoff, Siti Hajar; Zaini, Syasya Azra; Midi, Nur Shahida; Mohamad, Sarah Yasmin
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v8i2.1527

Smart street light is an intelligent control of street lights to optimize the problem of power consumption of the street, late in night. Conventional street lights are being replaced by Light Emitting Diode (LED) street lighting system, which reduces the power consumption. The focus of this project is to design a system of street lights controller to provide a reduction in power consumption. The prototype was designed by using Light Dependent Resistor (LDR), Infrared sensor (IR), battery and LED. The brightness of the lamps is being controlled in this project to reduce the power consumption. The dimming of the lamps depends on the speed of object motion detected such as pedestrians, cyclists and cars. The higher speed of moving object, the greater the level of intensity. For this idea, the innovation of street lights is not quite the same as conventional street lights that are controlled by timer switch or light sensor which automatically turns light on during sunset and off during sunrise. According to the study, motion detection devices may help to save up to 40% of energy per month.

Design and implementation of a series switching SPSI for PV cell to use in carrier based grid synchronous system Tawfikur Rahman; S. M. A. Motakabber; Muhammad I. Ibrahimy; A. H. M. Zahirul Alam
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

A carrier-based grid synchronous method is proposed to develop the system efficiency, phase and power quality of the inverter output waves. The operating principle of a single-phase phase synchronous inverter (SPSI) is introduced, with proper synchronous paid to the switching-frequency synchronizing voltage made by the interleaved process, as well as actual mitigation approaches. In the construction of the SPSI, input and output filters are electrically coupled with the two sides of an inverter. The inverter power electronic switches and other electrical components are operated by carrier-based grid synchronous controller (CBGSC) with PWM regulator. The SPSI is designed and implemented with the Toshiba 40WR21 IGBT, Digital Microcontroller pulse controller (DMPC) and 4N35 Optocoupler with a fundamental frequency of 50Hz. The other parameters are considered as load resistance, =11Ω, duty cycle, 85%, carrier frequency, 2.5kHz and input DC voltage, ± 340V. In addition, LCL lowpass grid filters are used to convert squire wave to sine wave with required phase and frequency. Finally, the simulated and experimental results obtained with a carrier-based grid synchronous SPSI experimental prototype are exposed for justification, showing the phase error of 55% improvement, reduced 11% of THD and the conversion efficiency of 97.02% highly predicted by the proposed design technique to improve the microgrid system.

Stability check of doubly fed induction generator (DFIG) micro grid power system Ameerul A. J. Jeman; Naeem M. S. Hannoon; Nabil Hidayat; Mohamed M. H. Adam; Ismail Musirin; Vijayakumar V.
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

As of late, expanding interest of renewable energy and consumption of non-renewable energy source have prompted developing advancement of renewable energy technology, for example, wind energy. Wind energy has turned out to be one of the reliable sources of renewable energy, which requests extra transmission capacity and better methods for sustaining system reliability. As of now, doubly fed induction generator wind turbine is the most well-known wind turbine. This paper focuses on DFIG wind farm design using MATLAB/SIMULINK and also investigates the issues of the system stability of the DFIG wind turbine micro grid power system. This analysis includes the changes of voltage, current, real power and reactive power based on various conditions of the power system.

Experimental study on transient response of fuel cell Ameerul A. J. Jeman; Naeem M. S. Hannoon; Nabil Hidayat; Mohamed M. H. Adam; Ismail Musirin; Vijayakumar V.
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

This research work discusses a control strategy to enhance the transient response of the fuel cell and boost the real and reactive power flow from grid connected to fuel cell. The current output of the fuel cell depends on the availability of hydrogen in the fuel cell stack, a battery bank is implemented to supply the transient current and to prevent it from hydrogen saturation. The battery should only supply when there is a transient. During steady state the total power is produced by the fuel cell by regulating its hydrogen input. A prototype of the system will be created to study a control scheme which regulates the current from an input source and a battery which is connected to a dc motor. The control philosophy is based on d-q transformation and subsequently generating a reference signal that is tracked by an IGBT based inverter. The speed of the motor is controlled using pulse with modulation. The dynamic modeling of the standalone fuel cell that is connected to a dc motor is carried out using MATLAB/SIMULINK platform. The simulation results show that the control scheme works well, although the dynamic response of the system can be improved. The testing carried on the prototype proves that the concept works well, but a hydrogen control scheme should be developed to improve the efficiency of the control scheme.

Low insertion loss of surface mount device low pass filter at 700 MHz Khairil Anuar Khairi; Mohd Faizal Jamlos; Surentiran Padmanathan; Mohd Aminudin Jamlos; Muammar Mohamad Isa
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

The paper involved with the design, simulation and fabrication of 6th order elliptical-based Surface Mount Device (SMD) LPF with cutoff frequency at 700 MHz. Fabricated LPF is consisted of four PCB layers which components of SMD are soldered on the top layer. Another three layers is for grounding and shielding, power supply and grounding void. The four layers is crucial to avoid interference between components. The research has find out that the momentum simulation is definitely required to improve the signals response compared to a normal simulation by ADS software. The comparison between momentum simulated versus measured and normal simulated versus measured is 0.2 dB and 29 dB correspondingly. Such huge difference leads to conclusion that momentum simulation is saving time without having much struggles and efforts to get optimum readings. The Proposed SMD LPF has a very low insertion loss of 0.965dB with a transition region of 195 MHz which is good steepness to avoid any image frequency.

Routing performance of structured overlay in Distributed Hash Tables (DHT) for P2P Rafiza Ruslan; Ayu Shaqirra Mohd Zailani; Nurul Hidayah Mohd Zukri; Nur Khairani Kamarudin; Shamsul Jamel Elias; R. Badlishah Ahmad
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

This paper presents a routing performance analysis of structured P2P overlay network. Due to the rapid development and hectic life, sharing data wirelessly is essential. P2P allows participating peers move freely by joining and leaving the network at any convenience time. Therefore, it exists constraint when one measuring the network performance. Moreover, the design of structured overlay networks is fragmented and with various design. P2P networks need to have a reliable routing protocol. In order to analyse the routing performance, this work simulates three structured overlay protocols-Chord, Pastry and Kademlia using OMNeT++ with INET and OverSim module. The result shows that Pastry is the best among others with 100% routing efficiency. However, Kademlia leads with 12.76% and 18.78% better than Chord and Pastry in lookup hop count and lookup success latency respectively. Hence, Pastry and Kamelia architectures will have a better choice for implementing structured overlay P2P network.

Page 5 of 9 | Total Record : 90

3 4 5 6 7

Filter by Year

2019 2019

Filter By Issues

All Issue Vol 8, No 4: December 2019 Vol 8, No 3: September 2019 Vol 8, No 3: September 2019 Vol 8, No 2: June 2019 Vol 8, No 2: June 2019 Vol 8, No 1: March 2019 Vol 8, No 1: March 2019 Vol 7, No 4: December 2018 Vol 7, No 3: September 2018 Vol 7, No 3: September 2018 Vol 7, No 2: June 2018 Vol 7, No 1: March 2018 Vol 6, No 4: December 2017 Vol 6, No 3: September 2017 Vol 6, No 2: June 2017 Vol 6, No 1: March 2017 Vol 5, No 4: December 2016 Vol 5, No 4: December 2016 Vol 5, No 3: September 2016 Vol 5, No 2: June 2016 Vol 5, No 2: June 2016 Vol 5, No 1: March 2016 Vol 5, No 1: March 2016 Vol 4, No 4: December 2015 Vol 4, No 4: December 2015 Vol 4, No 3: September 2015 Vol 4, No 3: September 2015 Vol 4, No 2: June 2015 Vol 4, No 1: March 2015 Vol 4, No 1: March 2015 Vol 3, No 4: December 2014 Vol 3, No 4: December 2014 Vol 3, No 3: September 2014 Vol 3, No 2: June 2014 Vol 3, No 1: March 2014 Vol 2, No 4: December 2013 Vol 2, No 3: September 2013 Vol 2, No 2: June 2013 Vol 2, No 1: March 2013 Vol 1, No 4: December 2012 Vol 1, No 3: September 2012 Vol 1, No 2: June 2012 Vol 1, No 1: March 2012 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
,

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location , INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
,

INDONESIA