cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
Redaksi Jurnal Rekayasa Mesin Jurusan Teknik Mesin Fakultas Teknik, Universitas Brawijaya Jl. MT. Haryono 167 Malang, Jawa Timur Indonesia 65145
Location
Kota malang,
Jawa timur
INDONESIA
Rekayasa Mesin
Published by Universitas Brawijaya
ISSN : 23381663     EISSN : 24776041     DOI : 10.21776/ub.jrm
Core Subject : Engineering,
Mechanical Engineering
Rekayasa Mesin is published by Mechanical Engineering Department, Faculty of Engineering, Brawijaya, Malang-East Java-Indonesia. Rekayasa Mesin is an open-access peer reviewed journal that mediates the dissemination of academicians, researchers, and practitioners in mechanical engineering. Rekayasa Mesin accepts submission from all over the world, especially from Indonesia. Rekayasa Mesin aims to provide a forum for national and international academicians, researchers and practitioners on mechanical engineering to publish the original articles. All accepted articles will be published and will be freely available to all readers with worldwide visibility and coverage. The scope of Rekayasa Mesin are the specific topics issues in mechanical engineering such as design, energy conversion, manufacture, and metallurgy. All articles submitted to this journal can be written in Bahasa and English Language.
Arjuna Subject : -
Articles 965 Documents
 52   53   54   55   56 
PENGARUH PENAMBAHAN ADJUSTER PADA KOMPOR BRIKET TERHADAP JARAK PEMBAKARAN DAN LAJU PERPINDAHAN PANAS KONDUKSI Haurissa, Jusuf; Riupassa, Helen; Nanlohy, Hendry; Suyatno, Suyatno
Jurnal Rekayasa Mesin Vol. 15 No. 1 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i1.1373

Abstract

The effective and efficient use of biomass briquettes is strongly influenced by the type of stove used and the way it is used. This study aims to design a briquette stove by adding an adjuster: the test fuel used honeycomb briquettes and forest fern charcoal. The heat transfer from burning honeycomb briquettes to a pot of water needs to be maintained so that the heat (temperature) remains constant during the combustion process. In the current use of briquettes, the distance between the briquette flame and the pot of water is unstable because the space is getting further away from the pool of cooking water. The combustion distance is getting farther because the bottom of the initial honeycomb briquettes burns out, causing the surface of the briquettes to decrease and move away from the surface of the water pot. Thus the heat given to the pool of water will reduce. The briquette stove needs to be added with an adjuster to overcome this problem. This adjuster serves to raise the honeycomb briquettes if the surface of the briquettes decreases. With the addition of an adjuster, it will be analyzed how much the heat transfer rate and the stability of the burning distance of the honeycomb briquettes will be. In this study, 2 test models will be used: a stove with an adjuster and a stove without an adjuster, using 14 holes in honeycomb briquettes made from forest ferns using starch (tapioca) adhesive. The distance between the surface of the briquettes and the pot of boiled water is 5 cm. The results showed that the briquette stove using an adjuster could maintain the stability of the combustion distance between the surface of the briquette and the pot of water being cooked with an average temperature t = 567.83 0C and conduction heat transfer q = 5285.699 Watt.
PENGARUH VARIASI KECEPATAN PUTAR DAN DIAMETER PIN TOOLS TERHADAP KUAT GESER DAN STRUKTUR MAKRO SAMBUNGAN FRICTION STIR WELDING DISSIMILAR HIGH DENSITY POLYETHYLENE-POLYPROPYLENE Suwanda, Totok; Ardiyansyah, Nur
Jurnal Rekayasa Mesin Vol. 14 No. 3 (2023)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v14i3.1376

Abstract

The purpose of this study is to find out the effect of pin tool turn speed and pin tool diameter on strong shear and macro structure on the friction stir welding dissimilar high-density polyethylene and polypropylene sheets. Variations in welding process parameters used in this study were: rotary speed of 980, 1560, 2360 rpm, and pin tool diameter of 4 and 5 mm. The shape of the cylinder pin, the feeding speed of 11 mm/min, and the plunge depth of 7.8 mm were maintained constant. The results showed that the highest shear strength value was obtained on the connection with a rotary speed of 1560 rpm and a pin tool diameter of 5 mm 4.8 N / mm2 or 23.71% of the tensile strength of raw material high density polyethylene. Observations of macro structures show that the pin tool diameter 5 mm has only slight defects in the stir zone.
DESAIN KONSEP PURWARUPA MESIN INJECTION MOLDING TIPE VERTIKAL UNTUK DAUR ULANG LIMBAH PLASTIK SKALA RUMAH TANGGA Sufiyanto, Sufiyanto; Niam, Waridin; Marfizal, Marfizal; Aziz, Myson
Jurnal Rekayasa Mesin Vol. 14 No. 3 (2023)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v14i3.1380

Abstract

Plastic waste is the main cause of environmental pollution. It is necessary to research the design of the Injection Molding machine to process plastic waste. This study describes the design concept of a vertical type Injection Molding machine prototype by considering the factors to be utilized by small-scale plastic recycling businesses. The design stage starts from the identification of component requirements to the design of 3D drawings. The results of this study obtained a prototype design of a Vertical Injection Molding Machine. The embodiment of the design is not only determined directly by the design team and the manufacturing team, but is obtained from customer requests described in the technical specifications. At the concept design stage, there are 5 sub-functions and each function has 3 to 4 options. From the combination of these sub-functions and options, 3 assembly sketches were obtained so that 3 alternative design concepts were obtained. From the results of the concept assessment, design concept C was chosen from several alternative concepts.
PENGARUH VARIASI SUDUT DAN JARAK PENEMBAKAN SANDBLASTING PADA PROSES PRETREATMENT TERHADAP KUALITAS PELAPISAN CAT DAN SIFAT KOROSI PADA BAJA KARBON RENDAH Saputra, Indra Adi; Widodo, Teguh Dwi; Yuliati, Lilis
Jurnal Rekayasa Mesin Vol. 15 No. 1 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i1.1382

Abstract

The purpose of this study was to determine the effect of variations in the angle and distance of sandblasting on paint coating quality and corrosion properties of low carbon steel. The success of a coating is highly dependent on surface roughness, so sandblasting is needed to clean and create a surface roughness profile with the aim that the paint can coat the surface perfectly. The test method used in this research is the pull off test method for testing the adhesive strength of paint and open circuit potential (OCP) for testing the corrosion potential. The sandblasting variations used are angles of 45⁰, 60⁰, 75⁰ and nozzle distances of 15 cm, 35 and 50 cm. The tests carried out were roughness, paint thickness, paint adhesive strength and corrosion potential. From the test results it can be concluded that the greater the angle and the closer the sandblasting nozzle distance, the greater the surface roughness. The greater surface roughness affects the paint layer to be thicker and has a high paint adhesion strength, resulting in a smaller corrosion potential. In this study, the highest test results were obtained at an angle of 75⁰ and a distance of 15 cm with a surface roughness value of 5.981 µm, a paint thickness of 115 µm, a paint adhesive strength of 7.28 MPa and an initial corrosion potential position of -0.101 V then a final position of -0.063 V.
THE EFFECT OF THERMAL RESISTANCE OF CEILING LAYER ON THE PERFORMANCE OF AN AIR CONDITIONER AND ROOM TEMPERATURE DISTRIBUTION Siang, Jeri Tangalajuk; Patabang, Daud
Jurnal Rekayasa Mesin Vol. 15 No. 1 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i1.1386

Abstract

The effectiveness of an air conditioner does not only depend on the design of the air-conditioner solely. Several factors affect the effectiveness of the cooling process of a room. One of the main factors in obtaining optimal results in the cooling process of a room is the rate of heat flow that enters a conditioned space. The amount of heat flow that enters a conditioned room affects the final temperature of the room. The ceiling is a part of the room that has a immense heat-flow rate. That is because the air temperature above the plafond is relatively high, and the thickness of the room plafond is relatively compact. It is necessary to analyze the room plafond material thermal resistance in increasing the heat absorbtion efficiency of household air conditioners. The thermal resistance of the material effect on the average room temperature, room temperature map, and the energy consumption is examined experimentally. The result shows that by occupying the plafond with a Styrofoam layer, the average room temperature decreases by 1.3⁰C, the air conditioner cooling capacity decreases by 0.402 kW, electric current decreases by 0.006 A compared to the existing room condition.
ANALISIS KINERJA MESIN ROTARY DRYER BERBAHAN BAKAR GAS LPG UNTUK PENGERINGAN GABAH Ritonga, Abdul Mukhlis; Mustaufik, Mustaufik; Hitapriya , Adeka Sangtraga; Khasanah, Jannata Utswatun
Jurnal Rekayasa Mesin Vol. 15 No. 2 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i2.1391

Abstract

Drying of grain is a process to reduce the water content. One of the obstacles in the drying process is the weather factor. The use of a rotary dryer with LPG gas fuel can be used as an alternative to dry grain. The purpose of this study was to determine the performance of the rotary dryer in grain drying including the optimum machine capacity, reduction in the moisture content of the material, drying energy, drying rate, and drying efficiency. The research method used is the experimental method. The condition of the grain moisture content tested was water content between 18%-22% and thermostat temperature between 50°C-60°C (treatment 1), moisture content between 23%-27%, and thermostat temperature between 60°C-70° C (treatment 2) with a total mass of 500 kg of grain. The results showed that the rotary dryer machine can be used to dry grain efficiently. The rotary dryer machine produces an average optimum capacity of 104.02 kg/hour in treatment 1 and 111.90 kg/hour in treatment 2, the decrease in water content in treatment 1 is 5.92% and in treatment 2 is 8.65%, drying energy in average 188.453 .1 kJ in treatment 1 and 162.862.7 kJ in treatment 2, Drying rate on average 2.71 % db/hour in treatment 1 and 4.47 % db/hour in treatment 2, Drying efficiency on average 32.67% in treatment 1 and 50.92 % in treatment 2.
A RECENT REVIEW ON THE FAILURE ANALYSIS OF BOILER TUBE Utomo, Faris Fadhil; Rashyid, Muhammad Ibnu; Nugraha, Ariyana Dwiputra; Muflikhun, Muhammad Akhsin
Jurnal Rekayasa Mesin Vol. 15 No. 2 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i2.1392

Abstract

The failure analysis in the industrial systems i.e. power plan, oil, and gas companies, has been reported by many researchers. One of the most reported has occurred in the Boiler system. Among the components of the boiler, problems, and failures often took place in the tube. The purposes of the recent study are to describe, classify, and review the latest update of the failure behavior of the boiler tube. The failure was formed by overheating, creep, stress corrosion, cracking, erosion, oxidation, and post-weld heat treatment (PWHT). The current works are listed based on the methods used to identify the failures, failure observations, and case studies updated from the boiler tube failure condition. The research suggests that to replace the failure tubes, analysis related to the stress induced outside and inside the tube, environment conditions, and lifetime maintenance works need to be considered.
ANALISIS PENGARUH MEDAN MAGNET TERHADAP UKURAN ATOMISASI BAHAN BAKAR CAMPURAN GASOLINE DAN BIOETANOL Nufus, Tatun Hayatun; Dianta Mustofa Kamal; Gun Gun R Gunadi; Candra Damis Widiawati; Asep Apriana; Muhammad Todaro
Jurnal Rekayasa Mesin Vol. 15 No. 2 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i2.1398

Abstract

The atomization process plays a very important role because the success or failure of combustion in the combustion chamber is influenced by the size of the liquid fuel mist. The occurrence of good atomization from atomized is determined by the size of the fuel droplets and the size of the nozzle diameter. Reducing the droplet diameter can increase the velocity, which can affect the Reynolds number and cause turbulence effects. The effect of turbulence provides a vortex effect, which enhances the heat transfer process between hot air and fuel particles in the combustion chamber. In this research, the effect of fuel magnetization on droplet size is analyzed. The fuel used is E0, E10, E20, E30, and E100, all types of fuel are channeled through an electromagnetic field of 1500 Gauss. Next, the particle size was tested using a Particle Size Analyzer, Bettersize BeNano 90 Zeta. The result was a decrease in particle size of 8-27%. The particle size measured using the PSA (particle size analysis) tool and theoretical calculations is <10% different. Each tool has an accuracy limit for PSA with a maximum accuracy of around 5%. These results provide initial information that the fuel magnetization process can improve engine performance.
IMO-COMPLIANT ANALYSIS OF THE LARGE ANGLE STABILITY OF CHEMICAL TANKERS DURING THE LOADING AND UNLOADING LIQUID CAUSTIC SODA Firdhaus, Ahmad; Pujo, Mulyatno Imam; Luqman, Hakim Muhammad; Sekar, Wangi Nimas Ayu
Jurnal Rekayasa Mesin Vol. 14 No. 3 (2023)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v14i3.1409

Abstract

MT. Sinar Masela 8831 DWT is a ship transporting oil and chemicals certified by IMO Chemical Class 2,3. According to Chapter B, SOLAS CHAPTER VII, regarding water safety, loading and unloading oil and chemicals is categorized as dangerous due to water damage and pollution. Various studies are needed to expedite the loading and unloading process to reduce damage and pollution in the waters. One of these studies is regarding the stability of ships in accordance with IMO criteria. The study was conducted to determine the ship stability on the MT. Sinar Masela is in the loading-unloading process. This study applies eight conditions with seven-compartment tanks on the ship using software to analyze the stability calculation when the loading-unloading process meets the stability criteria set by IMO A.749(18) Ch 3. The results show the measure of stability in eight conditions with a seven-compartment tank during the loading and unloading process has a higher GZ value in all states, which has met the IMO stability criteria. Comparison of stability calculations on loading and unloading has an average difference of 0.226 m at 2.075 deg at the GZ value in each condition.
PENINGKATAN PRODUKSI BAHAN BAKAR HIDROGEN DENGAN BANTUAN NATURAL SURFACTANT PADA PROSES WATER SPLIT Purnami, Purnami; Dewi, Fransisca Gayuh Utami; Wardana, ING; Sasongko, Mega Nur; Yusuf, M Umar; Nugroho, Willy Satrio
Jurnal Rekayasa Mesin Vol. 15 No. 1 (2024)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v15i1.1413

Abstract

Hydrogen is an alternative fuel due to its environmental friendliness and abundance. Hydrogen can be produced through water-splitting technique, in which the Oxygen (O2) and Hydrogen (H2) are separated. Water electrolysis is one of many causes of water-splitting that effectively results H2 with high purity. One drawback of electrolysis is the low efficiency. In this study, a rice straw natural surfactant was utilized to improve the efficiency. Rice straw with the volume of 5 ml, 10 ml, dan 15 ml were added to the electrolyte solution. This study shows the rice straw based natural surfactant contains hydrophilic and hydrophobic sides. Both sides capable to reduce the surface tension of the solution which destabilizes water molecules. The aromatic magnetic field of rice straw surfactant homogenizes the water net dipole moment due to the diamagnetism of water. These contributes towards the weakened hydrogen bond of the water in the solution. The synergy between hydrophobic and hydrophilic sides is potent to alter hydrogen production rate through intrinsic magnetism.

Page 54 of 97 | Total Record : 965

 52   53   54   55   56 

Filter by Year

2010 2025


Reset
Filter By Issues
All Issue Vol. 16 No. 3 (2025) Vol. 16 No. 2 (2025) Vol. 16 No. 1 (2025) Vol. 15 No. 3 (2024) Vol. 15 No. 2 (2024) Vol. 15 No. 1 (2024) Vol. 14 No. 3 (2023) Vol. 14 No. 2 (2023) Vol. 14 No. 1 (2023) Vol. 13 No. 3 (2022) Vol. 13 No. 2 (2022) Vol. 13 No. 1 (2022) Vol 12, No 2 (2021) Vol 12, No 1 (2021) Vol 11, No 3 (2020) Vol 11, No 2 (2020) Vol 11, No 1 (2020) Vol 10, No 3 (2019) Vol 10, No 2 (2019) Vol 10, No 1 (2019) Vol 9, No 3 (2018) Vol 9, No 2 (2018) Vol. 9 No. 1 (2018) Vol 9, No 1 (2018) Vol 8, No 3 (2017) Vol 8, No 2 (2017) Vol 8, No 1 (2017) Vol 7, No 3 (2016) Vol 7, No 2 (2016) Vol. 7 No. 2 (2016) Vol 7, No 1 (2016) Vol 6, No 3 (2015) Vol 6, No 2 (2015) Vol 6, No 1 (2015) Vol 5, No 3 (2014) Vol 5, No 2 (2014) Vol 5, No 1 (2014) Vol 4, No 3 (2013) Vol 4, No 2 (2013) Vol 4, No 2 (2013) Vol 4, No 1 (2013) Vol 3, No 3 (2012) Vol 3, No 3 (2012) Vol 3, No 2 (2012) Vol 3, No 1 (2012) Vol 3, No 1 (2012) Vol 2, No 3 (2011) Vol 2, No 2 (2011) Vol 2, No 1 (2011) Vol 1, No 3 (2010) Vol 1, No 2 (2010) Vol 1, No 1 (2010) More Issue