Claim Missing Document
Check
Articles

Found 3 Documents
Search
Journal : Jambura Journal of Electrical and Electronics Engineering

Analisis Tegangan Tembus Dan Hidrofobisitas Isolator Nano Komposit Resin Epoksi Dan SiO2 Amelya Indah Pratiwi; Muhammad Asri
Jambura Journal of Electrical and Electronics Engineering Vol 3, No 2 (2021): Juli - Desember 2021
Publisher : Teknik Elektro - Universitas Negeri Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (237.073 KB) | DOI: 10.37905/jjeee.v3i2.10763

Abstract

Penelitian ini bertujuan untuk mengetahui karakteristik tegangan tembus dan sifat hidrofobik dari isolator resin epoksi dengan dan tanpa bahan pengisi abu arang tongkol jagung. Penambahan bahan pengisi sebanyak 15 gram, 30 gram dan 45 gram abu arang tongkol jagung, DGEBA 100 ml, MPDA 50 ml. Metode pengujian tegangan tembus berdasarkan standar IEC 1109 dan metode pengukuran hidrofobisitas berdasarkan IEC 62073 yakni metode sudut kontak. Nilai Tegangan tembus tertinggi  pada sampel SI00 (tanpa filler) kondisi kering bersih yakni sebesar 74,64 kV dan tegangan tembus terendah pada sampel SI45 kondisi kering bersih sebesar 17,81 kV. Penambahan jumlah sampel bahan pengisi hanya memperburuk tegangan tembus isolator. Sampel SI00, SI15, SI30, dan SI45 bersifat hidrofilik atau menyerap air. Penambahan bahan pengisi pada resin epoksi juga semakin membuat permukaan isolator menyerap air. Pada sampel dengan bahan pengisi 45 gram abu tongkol jagung sudah mengalami breakdown pada tegangan 17,81 kV sehingga tidak dilanjutkan untuk kondisi pengujian yang lain.This study aims to measure the breakdown stress and hydrophobic properties of epoxy resin insulators with and without corncob charcoal ash as filler. Addition of filler as much as 15 grams, 30 grams and 45 grams of corncob charcoal ash, 100 ml DGEBA, 50 ml MPDA. The breakdown voltage testing method is based on IEC 1109 standard and the hydrophobicity measurement method according to IEC 62073 is the contact angle method. The highest value of the breakdown voltage in the SI00 sample (without filler) is in the clean dry condition of 74.64 kV and the lowest in the SI45 sample in the clean dry condition is 17.81 kV. Increasing the sample size of the filler only exacerbates the breakdown voltage of the insulator. Samples SI00, SI15, SI30, and SI45 are hydrophilic or absorb air. The addition of fillers to the epoxy resin also makes the surface of the insulator absorb air. In the sample with 45 grams of corn cobs ash filler, it has been damaged at a voltage of 17.81 kV so that it cannot be used for other test conditions. 
Sistem Monitoring Informasi Kualitas dan Kekeruhan Air Tambak Berbasis Internet of Things Sudirman Melangi; Muhammad Asri; Stephan Adriansyah Hulukati
Jambura Journal of Electrical and Electronics Engineering Vol 4, No 1 (2022): Januari - Juni 2022
Publisher : Teknik Elektro - Universitas Negeri Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (529.438 KB) | DOI: 10.37905/jjeee.v4i1.12061

Abstract

Terjadinya perubahan keadaan air tambak yang tidak dapat diprediksi, yang disebabkan oleh suhu, kandungan atau unsur-unsur yang terlarut dalam air tambak dapat mempengaruhi mutu dari hasil budidaya tambak, dan petani tidak dapat memantau terus-menerus perubahan keadaan air tambak mereka secara langsung, maka dibuatlah penelitian ini dengan tujuan membuat sistem monitoring untuk menginformasikan kualitas dan kekeruhan air pada tambak dengan konsep Internet of Things (IoT) dengan menampilkan secara realtime nilai kualitas dan kekeruhan air menggunakan Smartphone. Obyek pengujian berasal dari dua sampel air tambak yang berbeda dan satu air sumur sebagai pembanding. Metode pada sistem monitoring menggunakan dua sensor agar lebih akurat dalam melihat kondisi air tambak, sensor TDS meter untuk mendeteksi kualitas air dan sensor SEN0189 untuk mendeteksi kekeruhan air, kemudian data sensor dikirim menggunakan konsep IoT dimana mikrokontroler NodeMCU sebagai penerima data sensor bertindak sebagai pengirim informasi keadaan air secara online ke Smartphone menggunakan aplikasi Blynk. Dari hasil pengujian sistem monitoring pada aplikasi Blynk dapat menampilkan grafik dari data kualitas air dalam satuan ppm dan data kekeruhan air dalam satuan mg/l, rata-rata sensor mendapatkan data untuk kedua sampel air tambak dengan nilai yang tinggi, sedangkan sampel air sumur lebih rendah.Unpredictable changes in pond water conditions caused by temperature, content, or dissolved elements in pond water can affect the quality of freshwater aquaculture. As farmers are not able to continuously monitor changes in the state of their pond water directly, this study was made with the aim of creating a monitoring system to inform pond water quality and turbidity with the Internet of Things (IoT) concept, by displaying in real-time the quality and turbidity values using a smartphone. The objects of the test were taken from two different pond water samples and one well water for comparison. The method used in the monitoring system is two sensors, in order to increase the accuracy in observing the condition of pond water, where the TDS meter sensor was used to detect water quality, and the SEN0189 sensor was to detect water turbidity. The sensor data was sent using the IoT concept, where the NodeMCU microcontroller as the sensor data receiver sends information on the condition of the water to the Smartphone using the Blynk application. The results of the monitoring system test on the Blynk application can display the graph of water quality data in ppm units and water turbidity data in mg/l units, where the average sensor receives data for both pond water samples with high values, while well water samples are lower. 
Rancang Bangun Prototipe Peringatan Dini Banjir Menggunakan Raspberry Pi Berbasis IoT Restu Adjie priatim; Muhammad Asri; Syahrir Abdussamad
Jambura Journal of Electrical and Electronics Engineering Vol 5, No 2 (2023): Juli - Desember 2023
Publisher : Electrical Engineering Department Faculty of Engineering State University of Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37905/jjeee.v5i2.19696

Abstract

Permasalahan yang sering terjadi ketika adanya bencana alam berupa tanah longsong, angin ribut, banjir, gempa bumi adalah tidak adanya peringatan dini untuk masyarakat yang terdampak bencana alam, sehingga hal ini banyak merugikan masyarakat yang saat itu tidak sempat menyelamatkan barang-barang atau benda-benda yang dianggap penting. Berdasarkan permasalahan ini maka peneliti akan membuat prototipe peringatan dini bencana alam. Prototipe alat yang akan dibuat adalah peringatan dini untuk bencana banjir dengan tujuan untuk membantu masyarakat agar supaya dapat mengetahui lebih dini mengenai bencana banjir ini serta diharapkan dapat meminimalisir kerugian bagi masyarakat. Metode yang digunakan adalah perangcangan dan eksperimen. Sistem peringatana ini merupakan alat peringatan awal akan terjadinya banjir dengan mendeteksi ketinggian air dengan menggunakan Raspberry Pi sebagai pengontrolnya dan IoT sebagai sistem pengiriman informasi kondisi ketinggian air. Alat ini dibuat dari rangkaian pendukung seperti sensor HC-SR04 sebagai pendeteksi ketinggian air, LED sebagai lampu indikator ketinggian air, dan buzzer sebagai alarm peringatan. Sistem IoT bekerja dengan baik dan mengirimkan informasi tentang kondisi ketinggian air yang telah ditentukan. Dari hasil pengujian alat ini sistem mendeteksi level air yang dapat mengirimkan informasi level normal, waspada, siaga, dan awas sebagai level tertinggi, serta dapat mengirimkan notifikasi dan suara alarm yang akan berbunyi pada saat level waspada dan siaga terjadi secara otomatis, informasi juga akan dikirim ke smartphone menggunakan aplikasi Blynk. Dengan demikian sistem deteksi ini dapat dimanfaatkan untuk mengirimkan informasi lebih awal jika terjadinya bencana banjir.The problem that often occurs when there are natural disasters in the form of landslides, hurricanes, floods, earthquakes is that there is no early warning for people who support natural disasters, so this is detrimental to the people who at that time did not have time to save goods or objects. which is considered important. Based on this problem, researchers will create a prototype of natural disaster early warning. The prototype tool that will be made is an early warning against floods with the aim of helping the community to find out earlier about this flood disaster and is expected to minimize losses for the community. The method used is design and experiment. This warning system is an early warning tool for flooding by detecting the water level using the Raspberry Pi as the controller and IoT as a system for sending information on the condition of the water level. This tool is made of a series of supports such as the HC-SR04 sensor as a water level detector, an LED as a water level indicator light, and a buzzer as an alarm warning. The IoT system works well and sends information about predetermined water level conditions. From the test results of this tool a water level detection system that can send information on normal, alert, standby and alert levels as the highest level, and can send sound notifications and alarms that will sound when the alert and standby levels occur automatically, information will also be sent to a smartphone using the Blynk app. Thus this detection system can be used to send information earlier if a flood disaster occurs.