Claim Missing Document
Check
Articles

Found 11 Documents
Search

Studi Kualitas Energi Listrik Gedung Fakultas Teknik Universitas Bangka Belitung Asmar Asmar; Wahri Sunanda
Jurnal Serambi Engineering Vol 6, No 2: April 2021
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v6i2.2916

Abstract

One of the performances of the electric power system can be seen from the quality of electrical energy. In this study, the measurement of the quality of electrical energy was carried out using a power quality meter to obtain the values of current, voltage, frequency, total current harmonic distortion and total voltage harmonic distortion in the building of the Faculty of Engineering, Universitas Bangka Belitung. From measurements on the 3 existing buildings, it was found that the measured voltage value range was still at  + 5% to - 10% of the 220 Volt secondary distribution voltage value and the frequency value was still in the range of 49.5 Hz to 50.5 Hz. The total value of voltage harmonic distortion is still below the required value, but the total value of current harmonic distortion is above the required value.
Analisis Kelayakan Pemasangan Load Break Switch (LBS) Penyulang Rindik Pada Proses Manuver Antar Penyulang Di PLN ULP Toboali Syarifah Syarifah; Rudy Kurniawan; Asmar Asmar
ELECTRON : Jurnal Ilmiah Teknik Elektro Vol 2 No 1 (2021): Jurnal Electron, Mei 2021
Publisher : Jurusan Teknik Elektro Fakultas Teknik Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Sistem distribusi tenaga listrik merupakan hal yang sangat penting terhadap penyaluran listrik ke konsumen, terutama pada kontinyuitas pelayanan tegangan dan daya. saat ini dikarena adanya maintenence circuit Breaker pada penyulang Rindik, maka penyulang Rindik harus dilakukan manuver beban dengan pemasangan Load Break Switch diantara kedua penyulang. dari itu perlu dilakukan analisis mengenai aliran daya antara kondisi eksisting dan sesudah manuver, didapatkan berdasarkan Simulasi Software pada kondisi pertama dilihat dari tegangan ujung penyulang Bencah yaitu 19,423 kV, dengan Rugi-rugi daya sebesar 0,196 MW. Hasil aliran daya kondisi kedua dapat dilihat pada tegangan ujung pada penyulang Bencah yaitu sebesar 18,153 kV dengan rugi daya sebesar 0,294 MW dan Hasil Simulasi Software kondisi ketiga aliran daya dapat dilihat dari ujung penyulang Bencah dan penyulang Kota, nilai tegang ujung penyulang Bencah yaitu sebesar 18,769 kV dan tegangan ujung pada penyulang Kota yaitu sebesar 19,395 kV dengan rugi daya keseluruhan yaitu sebesar 0,304 MW. Dilihat dari hasil simulasi 3 kondisi simulasi manuver yang dilakukan, manuver beban yang menghasilkan tegangan ujung yang baik, serta memiliki rugi-rugi daya yang paling kecil, adalah pada simulasi manuver kondisi pertama sehingga dapat dinyatakan Load Break Switch Gang asem kondisi pertama layak untuk dipasang.
Pengaruh Temperatur Deproteinasi Pada Deasetilasi Kitin Cangkang Udang Krosok (Penaeus semisulcatus) Terhadap Adsorpsi Logam Besi (Fe) Herman Aldila; Asmar Asmar; Verry Andre Fabiani; Desy Yuliana Dalimunthe; Megiyo Megiyo; Riko Irwanto
Stannum : Jurnal Sains dan Terapan Kimia Vol 2 No 1 (2020): April
Publisher : Department of Chemistry - Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/jstk.v2i1.1722

Abstract

Penelitian ini bertujuan menganalisis pengaruh variasi temperatur deproteinasi pada daya adsorbsi kitosan udang krosok (Penaeus semisulcatus) terhadap logam besi (Fe) pada air kolong bekas penambangan timah timah di Pulau Bangka. Bahan baku kitosan yang digunakan dalam penelitian ini merupakan limbah cangkang udang krosok dari industri rumah tangga pembuatan ebi. Kitosan limbah cangkang udang ebi telah disintesis dalam tiga tahapan meliputi: deproteinasi, demineralisasi, dekolorisasi dan deasetilasi. Pada penelitian ini proses sintesis menggunakan variasi temperatur deproteinasi masing-masing: 30oC, 60oC, dan 90oC. Berdasarkan analisis data FTIR, dapat ditentukan nilai derajat deasetilasi sampel berturut-turut sebesar: 32,01% ; 30,94% dan 28,74%. Peningkatan temperatur deproteinasi menyebabkan nilai derajat deasetilasi kitosan menjadi menurun. Penurunan ini diakibatkan oleh rusaknya struktur kitin pada sampel akibat temperatur yang meningkat. Kandungan logam Fe pada air kulong yang digunakan dalam penelitian ini mencapai 6,1 ppm. Adsorbsi kitosan pada logam Fe dapat menurunkan kadar terlarut mencapai rata-rata 99,67% dari kadar awal. Kandungan gugus hidroksil pada kitosan menyebabkan terjadinya reaksi pembentukan senyawa hidroksida turunan dari logam besi terlarut. Senyawa besi hidroksida tersebut akan terpisah dari air dan membentuk endapan. Semakin besar nilai derajat deasetilasi maka akan semakin besar kandungan gugus hidroksil sehingga menyebabkan daya adsorbsi kitosan semakin meningkat.
PENGARUH KETIDAKSEIMBANGAN BEBAN TERHADAP STABILITAS STEADY STATE Asmar Asmar
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 5 No 1 (2018): Jurnal Ecotipe, April 2018
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/ecotipe.v5i1.33

Abstract

The stability of the electric power system is related to the balance of power in the system. When a power change occurs, the rotor will swing affecting the power angle, rotation speed, frequency and stability of the system. The Unbalanced load causes the momentary power of the generator to contain the sinusiodal component. To know the effect of sinusiodal component, must be known relation between power angle with momentary power. The relationship is determined by the symmetric component method. The power angle relationship with the momentary power obtained is applied to the swing equation. With the linearization of the equation, it can be seen the effect on steady state generator stability. The results showed that an increase in load imbalance caused a decrease in the stability limit.
RANCANG BANGUN UNIPOLAR PWM UNTUK PENGENDALIAN RANGKAIAN H-BRIDGE MENGGUNAKAN OPERATIONAL AMPLIFIER Asmar Asmar
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 1 No 1 (2014): Jurnal Ecotipe Vol.1 No.1 April 2014
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/ecotipe.v1i1.39

Abstract

Unipolar PWM control technique carried out by comparing triangular wave with two control voltages. The resulting pulses are used to control H-Bridge circuit. The technique can be done by using the functions of the operational amplifier. There are three main circuits needed is a triangular wave circuit, voltage control circuit, and a comparator circuit. With proper adjustment between the triangular waves and voltage control, voltage regulation will be obtained smooth.
PENDAYAGUNAAN CANGKANG BASAH EX HYDROCYCLONE PABRIK KELAPA SAWIT PT. PALMINDO MITRA LESTARI UNTUK PEMBANGKIT LISTRIK TENAGA BIOMASSA Muhamad Samsir; Wahri Sunanda; Asmar Asmar
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 2 No 1 (2015): Jurnal Ecotipe Vol.2 No.1 April 2015
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/ecotipe.v2i1.54

Abstract

This study aims to determine the potential of biomass electricity generated from the shell the rest of the production of palm oil mill PT. Palmindo Mitra Lestari. By converting the value of the availability of shells obtained within one hour of production with a calorific value of 23569.2595 kJ / kg and converted to 3,600,000 kJ / h = 1 MW to get the value of the power generated. The potential power output if the operating hours of the system clock generator adapted to production amounted to 13,660 MW. Average potential power that can be generated from the production of eggshell during 2013 Ex Hydrocyclone if the generating system operates 24 hours non-stop to reach 8.972 MW each hours.
ANALISIS TRANSFER DAYA PADA SALURAN TRANSMISI 150 KV DARI GARDU INDUK AIR ANYIR KE GARDU INDUK SUNGAILIAT PLN AREA BANGKA Diaz Dwiki Feranda; Asmar Asmar; Rudy Kurniawan
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 6 No 1 (2019): Jurnal Ecotipe, April 2019
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/ecotipe.v6i1.941

Abstract

Ketersediaan energi listrik yang cukup dan berkualitas merupakan tuntutan yang harus dipenuhi oleh PT. PLN (Persero). Penyaluran tenaga listrik melalui saluran transmisi 150 kV dengan jarak yang relatif panjang dan menggunakan kawat penghantar jenis aluminium selalu mengalami perubahan arus dan tegangan sehingga menimbulkan kemampuan pengiriman daya listrik menjadi tidak setabil. Pengaruh lainnya juga dapat diperoleh dari perubahan faktor daya dan sudut fasanya. Metode yang digunakan adalah metode analisis persamaan dalam bentuk hiperbolis. Pada penelitian ini menunjukkan bahwa kemampuan transfer daya dipengaruhi oleh sudut fasa. Kemampuan transfer daya aktif maksimum adalah sebesar 1962,71 kW pada VS yaitu 150?75? dan VR yaitu 150?0? dengan selisih sudut fasa adalah 75?. Sedangkan pada VS = 150?75? dan VR = 145?0? kemampuan transfer daya aktif adalah sebesar 1911,97 kW dengan selisih sudut fasa yang sama yaitu 75?. Penelitian ini memperlihatkan bahwa kemampuan transfer daya aktif dipengaruhi oleh tegangan. Kemampuan transfer daya aktif maksimum untuk nilai VR = 150?0? pada VS yang konstan yakni 150?90? adalah sebesar 2134,49 kW. Sedangkan Untuk nilai VR = 145?0? pada VS yang konstan yakni 150?90? adalah sebesar 2078,03 kW.
RANCANG BANGUN UNIPOLAR PWM DILENGKAPI DENGAN PENGATURAN FREKUENSI MENGGUNAKAN OPERATIONAL AMPLIFIER Asmar Asmar
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 6 No 1 (2019): Jurnal Ecotipe, April 2019
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/ecotipe.v6i1.942

Abstract

Pulse Width Modulation (PWM) diaplilaksikan pada rangkaian elektronika daya untuk pengendalian rangkaian konverter. Agar diperoleh kinerja yang baik, frekuensi pulsa PWM harus disesuaikan dengan jenis dan parameter konverter. Pada penelitian ini, pulsa PWM yang dihasilkan adalah unipolar PWM. Pulsa tersebut diperoleh dengan menggunakan tiga rangkaian utama, yaitu pembangkit gelombang segitiga, tegangan kontrol dan rangkaian pembanding. Komponen utama yang digunakan adalah Operational Amplifier (Op-Amp). Rangkaian yang dihasilkan dapat membangkitkan pulsa unipolar PWM dengan rentang frekuensi 30 Hz sampai dengan 5 kHz.
Rancang Bangun Aplikasi Sistem Inventory dengan Barcode di Laboratorium Teknik Elektro Universitas Bangka Belitung Asmar Asmar; Ghiri Basuki Putra
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 8 No 1 (2021): Jurnal Ecotipe, April 2021
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/jurnalecotipe.v8i1.1922

Abstract

The laboratory is a place for students to carry out practicum activities to better understand a subject. In the UBB Electrical Engineering laboratory, a lot of electronic tools and components are used so that an inventory of the equipment and components is needed so that they are easy to use. Previously, the inventory of goods at the Electrical Engineering Laboratory used a manual recording system so that its implementation was not running optimally and was still manual so that many problems occurred. To overcome this, an application is needed that is able to record equipment and components in the laboratory, the borrowing process, returns and the condition of existing goods automatically. This inventory application is made through several stages, namely, problem identification, design, application development and tool barcobe and application implementation stage. The application is made using data processing software, while the barcode is made using Barcode Studio. The results of this study have been applied to the Electrical Engineering Laboratory and are very helpful in the process of borrowing, returning, controlling the condition of existing goods in the laboratory, and making reports and can be done digitally and data storage becomes safer and electronic.
Perbandingan Efisiensi Konversi Energi Panel Surya Tipe Polycrystaline dengan Panel Surya Monocrystaline Berbasis Arduino di Kota Pangkalpinang Muhammad Yonggi Puriza; Welly Yandi; Asmar Asmar
Jurnal Ecotipe (Electronic, Control, Telecommunication, Information, and Power Engineering) Vol 8 No 1 (2021): Jurnal Ecotipe, April 2021
Publisher : Jurusan Teknik Elektro, Universitas Bangka Belitung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33019/jurnalecotipe.v8i1.2034

Abstract