Dwi Wahini Nurhajati, Dwi Wahini
Center for Leather, Rubber, and Plastic, Jl. Sokonandi No. 9 Yogyakarta

Published : 25 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 25 Documents
Search

Pengaruh dosis iradiasi sinar ultra violet pada pelapisan film pet dengan resin resol Nurhajati, Dwi Wahini
Majalah Kulit, Karet, dan Plastik Vol 9, No 17 (1994): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (840.789 KB) | DOI: 10.20543/mkkp.v9i17.415

Abstract

PET film coating process in this research is a photopolymerization process between resin resol (phenol resol or bisphenol A resol) with acrylate monomers on PET film via interaction with ultra violet – rays. Irradiation dose used in this research was varied from 420 mJ/cm2 to 1680 mJ/cm2. The result of an increasing in the irradiation dose. The increasing of irradiation dose caused the PET film surface more drying.INTISARI Proses pelapisan film PET pada penelitian ini merupakan proses photopolimerisasi resin resol (phenol resol bisphenol A resol) dengan monomer akrilat diatas film PET melalui interaksi dengan sinar ultra violet. Pada penelitian ini dosis iradiasi yang digunakan divariasi dari 420 mJ/cm2 sampai 1680 mJ/cm2. Dari hasil analisa diperoleh bahwa : Jumlah polimer yang terbentuk pada permukaan film PET naik dengan naiknya dosis iradiasi. Naiknya dosis iradiasi menyebabkan permukaan film pelapis bertambah kering
Pemanfaatan minyak kulit biji mete sebagai plasticizer dalam pembuatan sol sepatu Herminiwati, Herminiwati; Nurhajati, Dwi Wahini; Lestari, Sri Brataningsih Puji
Majalah Kulit, Karet, dan Plastik Vol 20, No 1 (2004): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2066.231 KB) | DOI: 10.20543/mkkp.v20i1.239

Abstract

The objective of the research was to study cashew nut shell liquid (CNSL) utilized as rubber plasticizer in shoe soles preparation. CNSL found from pressed cashew nut shells. CNSL consists of anacardict acid (90%) and cardol (10%). To remove the poison ivy, CNSL was treated by heating them at temperature 1200C for two hours. Sulfuric acid was also added to remove the impurities such as nitrogenous, sulphur and inorganic matters. Compounding process was carried out on two roll mill. Shoe sole compounds were prepared in various level of CNSL and Minarex B oil either separated formulation or in combination. Vulcanized rubber was then tested based on SNI 12-0172-1987 : Canvas shoes for general. The result of the research showed that CNSL can be utilized as rubber plasticizer in the shoe soles preparation. Compound with 5 phr CNSL provided good physical properties and conformed the requirements of SNI 12-0172-1987, such as tensile strength 136,4 kg/cm2, elongation at break 198,3%, tear resistance 63,56 kg/cm2, hardness 62,3 shore A, density 1,13 g/cm3, Grasselli abrasion resistance 0,711 mm3/ kgm, permanent set 6,40% and no crack detected on the flex cracking test. The research showed also that compound with the addition of 5 phr Minarex B oil into the compound, the CNSL provided better physical properties.  Keywords : cashew nut shell liquid, plasticizer, shoe soles.    Penelitian ini bertujuan untuk memanfaatkan minyak kulit biji mete (Cashew nut shell liquid) sebagai plasticizer karet dalam pembuatan sol sepatu. Minyak kulit biji mete (CNSL) diperoleh dari pengepresan kulit biji mete glondong. CNSL tersusun dari 90% asam anakardat dan 10% kardol. Untuk menghilangkan gatal dan toksisnya CNSL di –treatmen dengan pemanasan pada suhu 1200C selama 2 jam. Asam sulfat ditambahkan untuk menghilangkan pengotor seperti senyawa-senyawa nitrogen, sulfur dan bahan onorganik. Pembuatan kompon dilakukan dengan mesin two roll mill. Kompon sol sepatu dibuat dengan berbagi kadar CNSL maupun minyak Minerex B baik secara sendiri atau kombinasi. Vulkanisat karet diuji berdasar SNI 12-0172-1987 : Sepatu kanvas untuk umum. Hasil penelitian menunjukkan bahwa CNSL dapat dimanfaatkan sebagai plasticizer untuk pembuatan sol sepatu. Kompon dengan kadar CNSL sebesar 5 phr memberikan sifat fisis yang baik dan memenuhi syarat SNI 12-0172-1987, dengan sifat-sifat sebagai berikut : tegangan putus 136,4 kg/cm3,  perpanjangan putus 198,3%, ketahanan sobek 63,56 kg/cm2, kekerasan 62,3 shore A, bobot jenis 1,13 g/cm3,  ketahanan kikis Grasselli 0,711 mm3/kgm, perpanjangan tetap 6,40 % dan tidak retak pada uji ketahanan retak lentur. Penelitian juga menunjukkan bahwa dibandingkan dengan penambahan minyak Minarex B sebesar 5 phr, maka CNSL memberikan sifat fisis lebih baik. Kata Kunci : minyak kulit biji mete, plasticizer, sol sepatu.
Ekstraksi ion krom dalam asam nitrat dengan teknologi membran cair untuk limbah industri penyamakan kulit Nurhajati, Dwi Wahini; Prayitno, Prayitno; Kismolo, Endro
Majalah Kulit, Karet, dan Plastik Vol 15, No 2 (1999): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2504.551 KB) | DOI: 10.20543/mkkp.v15i2.258

Abstract

The objective of the research was to use of liquid membrane emulsion technique for the extraction of chrom in the nitrate acid solution. The liquid membrane phase as emulsion consists of kerosene as the solvent, sorbitan monooleat (span-80) as the surfactant, trioktil amin, as the carrier, natrium hidroksida as the internal phase. The optimum conditions obtained for making membrane, the liquid membrane phase was consists of organic phase (O), the internal liquid phase (W) with the ratio of O/W = 1, the concentration sorbitan monooleat (span-80) in the membrane phase was 4%(v/v), the optimum time to achieve a emulsion was 5 minutes, the rate of stirring for membrane 8000 rpm. The  optimum conditions obtained for extraction chrom ion as of chrom nitrate  from solution with percentage of liquid membrane extraction used of 97,8% and the percentage of liquid membrane extraction used of 97,8% and the percentage of liquid-liquid extraction of 81,24% were as follow : the concentration of nitric acid in external phase was 3M, the concentration of tri oktil amin in the membrane phase was 5% (v/v), the concentration of natrium hidroksida in internal phase was 1% (v/v), the extraction time was 15 minutes and volume ratio of membrane phase and external phase was 1 : 3. The addition of Fe and Zn ions solution decreased the percent extraction of chrom ion. INTISARI Penelitian ini bertujuan untuk meneliti teknik membran cair dalam ekstraksi krom pada larutan asam nitrat. Fasa membran yang berupa emulsi terdiri dari kerosene sebagai pelarut, sorbitan monooleat (span-80) sebagai surfaktan, tri oktil amin (TOA), sebagai zat pembawa serta natrium hidroksida sebagai fasa internal. Kondisi optimum yang diperoleh untuk pembuatan membrane cair, fasa membran terdiri dari fasa organic (O), fasa internal (W) dengan perbandingan O/W = 1, konsentrasi sorbitan monooleat dalam fasa membran 4%(v/v), waktu optimum pembuatan emulsi 4 menit, kecepatan pengadukan 8000 rpm. Kondisi optimum yang diperoleh untuk mengekstraksi krom dari larutan yang mengandung krom nitrat dengan prosen ekstraksi membran-cair sebesar 97,80% dan proses ekstraksi cair-cair sebesar 81,24% adalah sebagai berikut : konsentrasi asam nitrat dalam fasa eksternal adalah 3M, konsentrasi tri oktil amin dalam fasa membran adalah 5%(v/v), konsentrasi natrium hidroksida, dalam fasa internal 1%(v/v), 1 M dan lamanya waktu ekstraksi ialah 15 menit dan perbandingan  volume fasa membran dan volume fasa eksternal adalah 1 : 3. Penambahan ion ferro dan seng dalam larutan krom akan menurunkan prosen ekstraksi krom
Pengaruh variasi jumlah penggunaan RSS dan NBR terhadap sifat rol karet mesin cetak Musthofa, Hadi; Prayitno, Prayitno; Priyono, Bambang; Nurhajati, Dwi Wahini
Majalah Kulit, Karet, dan Plastik Vol 15, No 2 (1999): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1641.766 KB) | DOI: 10.20543/mkkp.v15i2.263

Abstract

-
Penelitian penggunaan monomer n-butil akrilat untuk peningkatan mutu kulit secara iradiasi Nurhajati, Dwi Wahini; Wiryodiningrat, Suliestiyah; Kadarijah, Kadarijah; Setyowati, Penny
Majalah Kulit, Karet, dan Plastik Vol 11, No 21 (1996): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (500.312 KB) | DOI: 10.20543/mkkp.v11i21.380

Abstract

Research on the utilization of n-butyl acrylate monomer for quality improvement leather by irradiation cobalt-60 gamma-rays is carried out as follows: Javanese crust hide was impregnated with water emulsions of n-butyl acrylate monomer for 2 hours, packed in to poly ethylene bags, sealed, then irradiated by cobalt-60 gamma rays (doses : 5 to 25 kGy). The irradiated leather was washed by water, dried and then physical tested. The results of physical  test of leather modified with n-butyl acrylate showed the increasing of tensile strength and elongation, decreasing of water absorption, resistance against the flexing test of 20,000 times, and PH was constant. Organoleptic test showed that the softly of the modified leather was no different with unmodified leather.  INTISARI Penelitian penggunaan monomer n-butyl akrilat untuk peningkatan mutu kulit secara iradiasi dilakukan dengan prosedur sebagai berikut : Kulit kras sapi Jawa diimpregnasi dengan emulsi monomer n-butil akrilat dalam air selama 2 jam, kemudian dimasukkan ke dalam kantung poli etilen, ditutup, selanjutnya diiradiasi dengan sinar gamma kobal-60 (dosis 5-25 kGy). Kulit yang sudah diradiasi dicuci dengan air, dikeringkan, lalu diuji sifat fisisnya. Hasil uji sifat fisis kulit yang telah dimodifikasi dengan monomer n-butil akrilat menunjukkan kenaikan kuat tarik dan kemuluran, penurunan penyerapan air, tahan terhadap bengkukan sebanyak 200.000  kali, dan PH tetap. Hasil pengamatan secara organoleptis menunjukkan  bahwa kelemasan kulit yang dimodifikasi tidak berbeda dengan kulit yang tidak dimodifikasi. 
Penelitian pengaruh teknik pencetakan kompon sol karet terhadap sifat fisisnya Nurhajati, Dwi Wahini; Suraswati, Agustin; Pramono, Pramono; Supriyadi, Supriyadi
Majalah Kulit, Karet, dan Plastik Vol 10, No 20 (1995): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1087.912 KB) | DOI: 10.20543/mkkp.v10i20.445

Abstract

The objective of this research is to know the influence of molding technique to the physical properties for rubber sole compound by a hydraulic press machine and a vulcanization molding machine. In the same process condition, there are physical properties different between the soles were molded by a hydraulic press machine and the soles were molded by a hydraulic press machine was reached on the vulcanization time 15 min at temperature 165C, and pressure 100 kg/cm2. Whereas optimal physical test value for the soles were molded by a vulcanization molding machine was reached on the vulcanization time 20 min, at temperature 165C, and pressure 1500 psi. INTISARI               Penelitian ini bertujuan untuk mengetahui pengaruh teknik pencetakan kompon sol karet dengan mesin “hydraulic press” dan mesin cetak vulkanisasi terhadap sifat fisisnya. Pada kondisi proses yang sama ada perbedaan sifat fisis antara sol yang dicetak dengan mesin “Hydraulic press” dan mesin cetak vulkanisasi. Sifat fisis optimal untuk sol karet yang di cetak dengan mesin “hydraulic press” dicapai dalam waktu 15 menit pada suhu 1650C dan tekanan 100 kg/cm2. Sedangkan sifat fisis optimal untuk sol karet yang dicetak dengan mesin cetak vulkanisasi dicapai dalam waktu 20 menit pada suhu 1650C dan tekanan 1500 psi. 
Pengaruh carbon black pada pembuatan plastik untuk irigasi sistem tetes Yuniari, Arum; Nurhajati, Dwi Wahini; Karsiati, Niken
Majalah Kulit, Karet, dan Plastik Vol 17, No 1-2 (2001): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1743.11 KB) | DOI: 10.20543/mkkp.v17i1-2.254

Abstract

The objective of this experiment was to know the influence carbon black was added to the plastics for drip irrigation systems. Plastics of 0,2 mm thickness for drip irrigation system was made from mixing of lwo density polyethylene (LDPE), high density polyethylene (HDPE) and carbon black by a blown film machine on the fixed processing condition. The investigated carbon black content were 0; 2,5; 5; 7,5; and 10 phr respectively and LDPE/HDPE ratio were 0/100, 50/50, 100/0 respectively. The physical properties tes showe and increasing of carbon black decreasing tensile strength, elongation at break, tear strength and brittleness. The best formulation was consist of HDPE 100 phr and carbon black 10 phr, with the physical properties as follows : tensile strength 158 kg/cm2, elongation at break 140%, and tear strength 91,46 kg/cm2.INTISARIPenelitian ini bertujuan untuk mengetahui pengaruh carbon black pada pembuatan plastic untuk irigasi system tetes. Plastic tebal 2 mm dibuat dari low density polyethylene (LDPE), high density polyethyln (HDPE) dan carbon black menggunakan mesin blown film pada kondisi proses yang tetap. Carbon black yang digunakan adalah 0; 2,5; 5; 7,5; 10 phr dan ratio LDPE/HDPE adalah 0/100, 50/50, 100/0 phr. Sifat fisis menunjukkan bahwa kenaikan carbon black menurunkan kuat tarik, kemuluran, kuat sobek dan kerapuhan. Formulasi terbaik terdiri dari HDPE 100 phr dan carbon black 10 phr, dengan sifat fisis sebagai berikut : kuat tarik 158 kg/cm2, kemuluran 140% dan kuat sobek 91,46 kg/cm2.
Pengaruh alkali pada pembuatan film pelapis (“coating film”) menggunakan teknologi sinar ultraviolet Nurhajati, Dwi Wahini
Majalah Kulit, Karet, dan Plastik Vol 6, No 10-11 (1991): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1070.739 KB) | DOI: 10.20543/mkkp.v6i10-11.465

Abstract

Coating film in this research is defined as the product of polymerization (crosslinking) of acrylate monomers whit phenol resin directly on substrate via interaction with incide UV irradiation. A thin layer consist of phenol resin (resole or novolac), monofunctional acylate monomer (ECA), and hexafunctional acylate monomer (DPCA-60) gives the crossliked polymer under UV irradiation. In order to enhance the insoluble polymer yield, effect of alkali addition was studied. Ba(OH)2 and KOH are most effective for phenol and novolac, respectively, from the viewpoint of insoluble polymer yield. INTISARIFilm pelapis (“Coating Film”)dalam penelitian ini didefinisikan sebgai hasil polimerisasi (rantai silang) dari monomer-monomer akrilat dengan resin phenol, langsung pada substrat melaluiinsiden irradiasi sinar ultra violet. Lapisan tipis yang terbuat dari campuran resin phenol (resole atau novolak), monomer akrilat monofungsional (ECA) dan monomer akrilat hexafungsiona (DPCA-60) memberikan polimer rantaisilang dengan adanyya irradiasi sinar ultra violet (UV). Dalam hal untuk menaikkan hasil polimer yang tidak larut dalam pelarut, pengaruh alkami sebagai bahan tambahan diteliti.Ba(OH)2 merupakan alkali yang paling efektif untuk phenol resole dan KOH paling effektid untuk novoloak, dalam hal menaikkan hasil polimer yang tidak larut dalam pelarut.
Penggunaan resin epoksi untuk pegangan alat-alat dapur Nurhajati, Dwi Wahini; Suraswati, Agustin; Pramono, Pramono; Supriyanto B, Supriyanto B; Supriyadi, Supriyadi
Majalah Kulit, Karet, dan Plastik Vol 14, No 26 (1999): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (560.785 KB) | DOI: 10.20543/mkkp.v14i26.300

Abstract

Application of epoxy resin to make the kitchen tolls holder was investigated. Optimum compound of kitchen tools holder was reached for compound which it consist of epoxy resin : 100 parts, hardener 100 parts, carbon black 50 parts. Applied test in hot water show that the kitchen tools holder from research is better than the kitchen  tools holder from markets.   INTISARI Telah dilakukan penelitian tentang penggunaan resin epoksi untuk pegangan alat-alat dapur. Formula kompon pegangan alat dapur yang optimum dicapai untuk kompon yang berisi resin epoksi 100 bagian, hardener 100 bagian, dan carbon black  50 bagian. Hasil uji pemakaian dalam air panas menunjukkan bahwa pegangan alat-alat dapur hasil penelitian lebih baik dibandingkan pegangan alat-alat dapur yang ada di pasaran. 
Komposit dari sampah plastik fleksibel dan serbuk gergaji Nurhajati, Dwi Wahini; Yuniari, Arum; Herminiwati, Herminiwati; Lestari, Sri Brataningsih Puji
Majalah Kulit, Karet, dan Plastik Vol 19, No 1 (2003): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1668.277 KB) | DOI: 10.20543/mkkp.v19i1.245

Abstract

A composite made from the flexsible plastic waste and saw dust was studied. The objectives of this research was to find the optimum ratio of the flexible plastic waste and saw dust in its application on a floor tile. The investigated ratio of flexible plastic waste / saw dust were 100/0; 90/10; 80/20; 70/30; 60/40; and 50/50 respectively. The composites were prepared on a rheocord-90 machine at 600C for 10 minutes. The composites were tested for their physical properties I, e flexibility, dimensional stability, curling, volatility, tensile strength, elongation at break, and hardness. The physical properties testing result show that a composite by using the flexible plastic waste and saw dust in comparation of 90/10 could meet the requirements of SNI 03/4060/1996 for Vinyl Floor. The increasing saw dust content in composites decreased tensile strength, elongation at break, flexibility, and hardness, but increased dimensional stability, and volatility. Tensile strength of all composites was higher than particle board.   Keywords : composites, flexible plastic waste, saw dust, floor tile.