Garuda - Garba Rujukan Digital

p-Index From 2021 - 2026

2.782

P-Index

This Author published in this journals

All Journal Jurnal Pengabdian Kepada Masyarakat Universitas Bangka Belitung PROMINE Jurnal GEOSAPTA IKRA-ITH ABDIMAS MINERAL JAGE

Delita Ega Andini

Program Studi Teknik Pertambangan, Fakultas Teknik , Universitas Bangka Belitung

Author-ID : 5340726

Humanities Civil Engineering, Building, Construction & Architecture Computer Science & IT Earth & Planetary Sciences Education Energy Engineering Environmental Science Materials Science & Nanotechnology Social Sciences Other

Published : 34 Documents Claim Missing Document

Claim Missing Document

Articles

Title

1 2 3

Kajian Teknis Geometri Jalan Tambang Front 242 Untuk Pencapaian Produktivitas Alat Angkut Di PT Semen Padang (Persero) Tbkntuk Pencapaian Produktivitas Alat Angkut Di PT Semen Padang (Persero) Tbk Jeffry Reynold Silalahi; Delita Ega Andini; Guskarnali Guskarnali
MINERAL Vol 3 No 2 (2018): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

PT Semen Padang (Persero) Tbk is one of the cement producing companies in Indonesia. The supply of limestone used as the main raw material in the manufacture of cement is obtained through the mining process in the IUP area of the company. Mining roads are one of the facilities that must be considered in limestone mining activities because it is a major support in the process of transporting limestones obtained from the working Front. Inadequate road conditions can lead to less productive means of transport in the transport process, which causes production inaccessibility. The mining roads in the 242 working Front are considered to be poor so that a technical study of the mine road is required in accordance with the AASHTO Manual Rular Highway Design standard so that the geometry of the mine road is not good enough so that improvements can be made, engineering studies include road width, cross slope, superelevation, road slope, as well as a study of the carrying capacity of the soil and the influence of the mine road on fuel consumption. Based on the results of the study, the geometry of the mine road is as followsthe haulage width of one lane is minimum 14 m, the width of the haul road is two lanes of 24 m, the width of the two lanes is 25 m minimum, the superelevation value is 1%, cross slope is 48 cm, the slope can be 16% of the vehicles are transported while the slope based on AASHTO is 10%, the slope of the road becomes the biggest factor that influences fuel consumption because it makes the conveyance exert great power. Mine path geometry that is not suitable causes a time of barrier of 86.85 seconds with a cycle time of 22.3 minutes using an average speed of 15 km / h resulting in a production of 1,343.04 tons / hour, while if made temporary road the transport means can reach ideal speed with time on average 29 km / h and 27 km / h, cycle time 17.75 minutes with a production of 1,687.4 tons / hour.

PENGARUH VARIABEL SHAKING TABLE TERHADAP KADAR DAN RECOVERY PENCUCIAN BIJIH TIMAH PRIMER PT MENARA CIPTA MULIA KABUPATEN BELITUN VARIABEL SHAKING TABLE TERHADAP KADAR DAN RECOVERY PENCUCIAN BIJIH TIMAH PRIMER PT MENARA CIPTA MULIA KABUPATEN BELITUNG TIMUR Dihan Fauzan; Janiar Pitulima; Delita Ega Andini
MINERAL Vol 3 No 2 (2018): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

The process of washing primary tin ore at PT Menara Cipta Mulia in the final stage uses gravity concentration method to separate mineral cassiterite from its impurity minerals. The separation process uses a shaking table with 2 stages of washing to minimize the waste of valuable minerals (losses). In the initial stages of washing, the primary shaking table and finishing stages use secondary shaking table. Currently the use of shaking tables at PT MCM does not have default standards in operation and still uses trial and error. Reseach method by varying the slope variables of the table in the primary tool shaking table 4 variations, namely 0.95°, 1.27°, 1.59°, 1.91° and washing water velocity of 3 variations, namely 0.6 m/s, 0.9 m/s, 1.2 m/s while on secondary shaking table tools 3 variations are slope that is 0.64°, 0.95°, 1.27° and washing water velocity of 3 variations is 0.6 m/s, 0.9 m/s, 1.2 m/s with this variable variation, the sample is obtained for the grade test and recovery calculation. The optimal results on the primary shaking table were at 1.27 degrees with an average recovery of 56.43% and grade Sn of 51.28%. Optimal water velocity is 0.9 m/s with an average recovery of 50.97% and grade Sn of 52.19%. While the optimal results for the secondary shaking table are at a slope of 0.64 degrees with recovery averaging 40.88% and grade of 71.64% with an optimal water velocity is 0.9 m/s with an average recovery of 32.24% with concentrate grade Sn 72.18%. The greater the value of the slope angle and water velocity be used, the smaller the recovery of washing tin ore produced but the smaller the recovery value indicates the higher the concentration of the resulting concentrate.

Pengaruh Fragmentasi Hasil Peledakan Batugranit Terhadap Produktivitas Hopper Crusher Di PT Bumi Warna Agung Perkasa Desa Air Mesu Kabupaten Bangka Tengah Bobby Bagaskara; Janiar Pitulima; Delita Ega Andini
MINERAL Vol 3 No 2 (2018): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

The destroyed process or to split the rock with blasted system have effective value and good economic compared with mechanical tools method. Blasted activity effective become is anothere standard the success of activity loading processing to influence achievement targets of mining productivity. This research aim to increasing the productivity hopper crusher baited rate and minimize total percentage of boulder, so that material reduction activity in hopper crusher become was more effective. The study was on 14 blasted is project from PT Bumiwarna Agung Perkasa. Data this research consist of geometry, blasted fragmentation, cycle time loading hopper. This research used method with geometry an estimates used R.L.Ash method with fragmentation analysis used Kuz-Ram and image analysis. From analysis data there is actual fragmentation 74.680% base on Kuz-Ram and 64.942% base on image analysis with an actual boulder total Kuz-Ram 25.320 % and 35.057% base on image analysis, with result the average time reduction 8.21 minute and an average productivity 131.80 m3/hour. It is minimize total percentage of boulder, needed to revise blasted geometry based on R.L. Ash theory with reduction boulder size >80 cm by 12.042% with keep the target volume production 40026.8 BCM. It is productivity hopper crusher may work better.

Identifikasi Penyebaran Zona Mineralisasi Endapan Timah Menggunakan Metode Induksi Polarisasi Konfigurasi Dipole - Dipole Di Bukit Sambunggiri Kecamatan Merawang Kabupaten Bangka Rafi Sasena; Guskarnali Guskarnali; Delita Ega Andini
MINERAL Vol 4 No 1 (2019): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

Tin is one of the many mining products found in the Bangka Belitung Islands region. Geophysical exploration was carried out in the Bukit Sambunggiri area, Merawang District, Bangka Regency using the dipole-dipole configuration polarization to detect polarizationel ectricity on surface of metal material and induction method to identify the distribution of tin deposit mineralization. The parameters is measuring area of 21 Ha with 6 tracks, length A, B, C is 640 meters, D, E, F is 840 meters, spacing between tracks 50 meters, spacing between electrodes 10 meters and equipment used is Multy Channel RS / IP Supersting. Processing measurement data using Res2dinv software to create 2D cross sections and Montaj Oasis for 3D cross sections. The results of resistivity and chargeability data processing of a total of six trajectories have 3 trajectories which have a clear mineralization area, that is, A trajectory is assumed to be at a distance of 250 - 350 meters and depths from 0 - 50 meters which are characterized by medium-high chargeability - 30) msec and low resistivity (<700) Ohm.m. On track D, it is estimated that there are three parts at a distance of 100 - 220 meters in depth of 50-50 meters, distance of 335 - 440 meters in depth of 50-130 meters and distance of 590 - 680 meters in depth of 50-130 meters. 430 meters at a depth of 0 - 150 meters. The results of interpretation of track A to track C are suspected to have zones of tin mineralization with secondary deposits and it is known that the mineralized zone is thought to be located below the bog iron zone with secondary tin deposits. This is due to the fact that the bog iron is hard rock like granite which is oxidized, so minerals that have a high level of resistance to weathering such as cassiterite and quartz will be released from the rock body and deposited in the lower layer. While path D to trajectory F is suspected to be the continuation of the zone of tin mineralization with primary deposits. This is presumably because the location of the mineralization area spreads between intrusion of granite rocks which have a high chargeability and resistivity value.

Evaluasi Keserasian Kerja Alat Gali Muat dan Alat Angkut Guna Pencapaian Target Produksi Batugamping 350.000 ton/bulan pada Pit 242 Bukit Karang Putih PT Semen Padang (Persero) di Kecamatan Lubuk Kilangan Sumatera Barat M.Arief Adilah; E.P.S.B Taman Tono; Delita Ega Andini
MINERAL Vol 4 No 1 (2019): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

The tendency of increasing demand for limestone as one of the raw materials for making cement, it is necessary to have appropriate mining to fulfill these needs. The importance of synchronization of loading and hauling equipments in working optimally and efficiently will influences the ability of mechanical devices in productivity. Match factors can find out the comparison of the number of loading and hauling equipment working in mining operations. Analysis of the calculation of match factors based on the circulating time of mechanical devices and the number of devices operating, data taken 30 times a month in July 2018. The primary data such as; circulation time of mechanical devices, resistance factors, bucket and vessel real capacity, effective working time of devices and number of devices, while secondary data such as; devices specifications, devices and operator work time, layout maps, rainfall and company production targets. The research method used is the calculation and analysis of quantitative data on factors that influence the ability of mechanical devices in production. The production target for limestone mining in pit 242 is 350,000 tons / month using a Hitachi ex 2500-6 Excavator unit synchronized with five units of Dumptruck Komatsu HD 785-7. Current devices production capability is 262,198.66 tons / month with a value factor of 0.80. The problem that occurs is not yet achieved the planned production target, this is due to the still low effective working time and work efficiency as a result of existing constraints. Efforts to increase production can be done by improving the effective working time of initially 637.99 minutes per day to 707.30 minutes per day or 81.29% of the total available working time, adding the number of bulk filling to 6 times and adding transportation equipment as many as two units, so that production increased to 361,415.82 tons per month and the value of the match factor for mechanical devices increased to 0.96.

Evaluasi Teknis Pengolahan Batu Granit Untuk Pencapaian Target Produksi 40.000 Ton/Bulan Pada PT Bumiwarna Agung Perkasa Di Desa Air Mesu Timur Bangka Tengah Reza Reza; E.P.S.B Taman Tono; Delita Ega Andini
MINERAL Vol 4 No 1 (2019): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

PT Bumiwarna Agung Perkasa, abbreviated as PT BWAP has a crushing plant which is divided into two units, namely primary crusher and the secondary crusher unit. Granite stone crushing plant of PT BWAP has production target 40.000 tons/month, but the production target has not been achieved, which 15.185,21 tons on June and 23.406,94 tons on July 2018, because there are production barriers which cause the available work of these two units to reduce and improve production targets, therefore to achieve production targets, evaluation of the demolition plant is needed. The method used in this study is the tool availability method. The data needed is the speed of feed raw material, tool working time, tool standby time and the weight of product samples taken on the conveyor belt. The main calculation of the primary primary crusher unit is very low at 32,67 % with a total production of only 26.940,20 tons/month and the secondary crushing unit is also very low at 42,45 % with a total production of 20.424,92 tons/month. After repairs, the working efficiency of the primary crusher unit increased to 75,69 % and the work efficiency of the secondary crusher increased to 78,15 % and to increase feeding to the secondary crusher unit, activating the two vibro feeders, so that the feed increased from 190,34 tons/hour to 260,06 tons/hour and the final production of crushing plant increased to 53.352 tons/month.

Analisis Keberhasilan Reklamasi berdasarkan Keputusan Menteri Energi dan Sumber Daya Mineral Nomor 1827 Tahun 2018 pada Lahan Bekas Tambang Air Jelitik 3 PT TIMAH Tbk Kabupaten Bangka Guskarnali Guskarnali; Regita Kasih Parenty; Delita Ega Andini
MINERAL Vol 4 No 2 (2019): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

PT Timah Tbk is a mining industry company which produces the tin metal. A mining former area which is chosen as the research location is Lahan Air Jelitik 3. This research aims to analyze the success of Lahan Air Jelitik 3’s reclamation based on Matrik 16 and Matrik 17 of Keputusan Menteri Energi Sumber Daya Mineral Nomor 1827 Tahun 2018. The research starts with collecting the primary data which consists of 43 and 29 coordinate points of Lahan Air Jelitik 3’s adjustment and revegetation, the length and width of 22 erosion in Blok 1, 24 erosion in Blok 2 and 4 landslide in both blocks, the height and diameter of 35 primary plants and the length of 5 cover crops. Those primary data and secondary data are processed by calculating the broad realization of Lahan Air Jelitik 3’s adjustment and revegetation, the amount of plants, the average of plant’s height and diameter, the stability of area and valuating the success of adjustment area, the success of revegetation, the success of last completion based on Matrik 16, also calculating the success reclamation value based on Matrik 17. The result of data processing shows the success value of adjustment and hoard area is 0.5, top soil’s spreading is 0.91, erosion and sedimentation’s control is 0, cover crop’s revegetation is 0.86, fast growing plant’s revegetation is 0.1765, local plant’s revegetation is 0.726, acid mine drainage’s management is 0, plant’s closure is 0.1059 and plant’s maintenance is 0.333. The reclamation’s success percentage 50.65% in Lahan Air Jelitik 3 PT Timah Tbk shows that the reclamation in that area is not good enough and the area needs improvement especially in plant’s maintenance, erosion and sedimentation’s control and acid mine drainage’s management.

Analisis Pengaruh Perubahan Nilai Total Moisture Dan Ash Content Terhadap Nilai Kalori Batubara Di Unit Pelabuhan Pt Bukit Asam Tbk Tarahan Bandar Lampung Alldino Hernanto; Janiar Pitulima; Delita Ega Andini
MINERAL Vol 5 No 1 (2020): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

The coal industry emphasizes the quality of coal because quality will always be directly related to consumers and the company's revenue because the higher the quality of coal, the more expensive the selling price of coal, therefore this research was conducted to determine the difference in coal quality in railroad cars (demolition) and when analyzing for stockpile, the effect of total moisture and ash content on coal calories and the factors causing these changes. In this study, qualitative and quantitative methods were used where the steps taken in this research were sampling in the railroad car and in the stockpile and then using the proximate analysis and analysis of coal calories from the analysis and correlation and regression analysis to determine the effect of total moisture and ash content. against coal calories. The proximate analysis of the coal samples is disassembly total moisture which is 8.49% ar, in the stockpile, which is 10.32 % ar ash content demolition which is 5.37, in the stockpile which is 8.62 % ar and the calorific value of demolition is 7181 cal/gr, in the stockpile that is 6800 kal / gr so that each of the total moisture parameters, ash content and calorific value changes by 1.40 % ar, at 3.25 % ar, and by 400 Kal / gr. Based on the regression results, the total effect of total moisture and ash content on the first calorie each increase of 1 % ar the total moisture value will reduce calories by 123.36 cal/gr, each increase of 1 % ar the value of ash content will reduce coal calorific value by 78.76 cal/gr. The change in value is due to the occurrence of contamination in the stockpile area, the occurrence of swabakar in the stockpile, and the influence of high rainfall on coal

Analisis Pengaruh Geometri Jalan Tambang Dari Front Penambangan ke Stockpile Terhadap Keselamatan Kerja PT Caritas Energi Indonesia Sarolangun Jambi Rika Fitriani; Guskarnali Guskarnali; Delita Ega Andini
MINERAL Vol 5 No 2 (2020): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

PT Caritas Energi Indonesia (CEI) is a company engaged in coal mining in Sarolangun Jambi. Based on the work accident data in the last 5 years of PT Caritas Energi Indonesia on the hauling coal getting road using dump truck transport Equipment Scania 380 P that resulted casualty and inflicted loss for the company both in terms of equipment repair and treatment of victims. The method on this research is to use quantitative data to calculate the width of straight road for sixty one segments, the width of bend road for fourteen segments, calculating the superelevation for fourteen segments, calculating hauling road slope (grade) for sixty one segments, calculating the cross slope for sixty one segments, analyzing the effect of road geometry on Occupational Health and Safety. The width of the straight road is 7 m for one line and 11 m for two lines, all segments were qualified, except Segment 0+400, Segment 0+700, Segment 1+600, thereforeit is necessary to increase the width of road to fit the standard, the width of the bend roadis 8 m for a single line and 13 m for two lines, all segments were qualified, exceptSegment 0+500, Segment 1+000 and Segment 4+100, superelevationbased on standard is 4%, not all of the superelevations were qualified so it needs to increase the width of the bend road so that it might avoid the centrifugal force while passing through the bend, all the grade of segmentswere qualified. PT Caritas Energi Indonesia didn’t have cross slope so the company needs to pay attention and make cross slope according to the standard of 40 mm/m. The geometry of the mining road of PT Caritas Energi Indonesia weren’t qualified, it might effectedwork accident so that it needs improvement accordance with standards

Perencanaan Sistem Pemompaan pada Penambangan Timah Primer Shaft Lacat 4 Pt Menara Cipta Mulia Kelapa Kampit Belitung Timur Aryuni Yusra Hamid; Delita Ega Andini; Haslen Oktarianty
MINERAL Vol 6 No 1 (2021): MINERAL
Publisher : Jurusan Teknik Pertambangan Universitas Bangka Belitung

This research was conducted to redesign the pumping system in the air drying process within a maximum of 25 days. The method used is descriptive and quantitative methods with actual data in the form of pressure and suction pipe elevation, pipe length and diameter, catchment area, actual discharge and pump head, location coordinates.The runoff discharge is 1.89 m3 / s, is prevented from entering the mine area by creating a channel with discharge flow of 2.12 m3 / s. The total volume on Shaft Lacat 4 is 34,591.7 m3 . The pump at a depth of 20 m has a discharge of 229.37 m 3 / hour, while a depth of 28 m has a discharge of 210.73 m3 / hour. Assuming the ground water is 200.64 m3 / hour, the addition of one pump with a discharge of 36 m3 / hour so that the drying time for 24 days is 11.8 hours. Production is stacking the sump of 1 x 1 x 1.5 m, making a channel with dimensions of 10 cm x 10 cm.

Co-Authors Aditya, Ismu Alamsyah, Muhammad Izhar Alfitri Rosita Alldino Hernanto Aryuni Yusra Hamid Bobby Bagaskara Dihan Fauzan Edwin Harsiga EPSB Taman Tono Fajar Indah Puspita Sari Ferdinand De Lessep Samosir Franto, Franto Franto, Franto Guskarnali, Guskarnali Haslen Oktarianty Irvani Irvani Irvani, Irvani Irvani, Irvani Janiar Pitulima Jeffry Reynold Silalahi Kristina Damayanti Panjaitan M.Arief Adilah Novi Herlinda Nur Annisa Oktarianty, Haslen Rafi Sasena Rahmad Tanjung Rajesta F. Wardana Ramadhan, Setiawan Regita Kasih Parenty Reza Reza Rika Fitriani Riztia Ramadhanti Silaban, Cindy Grestina Suryani Suryani

Title Search

Found 25 Documents Search Journal : MINERAL

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 25 Documents
Search
Journal : MINERAL