Garuda - Garba Rujukan Digital

All

Journal of Research and Technology

jrt
Website

Published by Universitas NU Sidoarjo

ISSN : 24605972 EISSN : 24776165 DOI : -

Chemical Engineering, Chemistry & Bioengineering Engineering Environmental Science Industrial & Manufacturing Engineering

Journal of Research and Technology published since 2015 contains a collection of a selected articles from the results of research and study of literature which is relevant to industrial , chemical, and environment engineering. Target readers of the Journal of Research and Technology are scientists, academics, and practitioners from various fields of industry.

Arjuna Subject : -

Articles 10 Documents

Search results for , issue "Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016" : 10 Documents clear

ANALISIS PENGARUH KUALITAS PELAYANAN AKADEMIK TERHADAP LOYALITAS MAHASISWA UNUSIDA DENGAN PENDEKATAN PARTIAL LEAST SQUARE (PLS) Untung Usada; Luqman Hakim; Anita T. Kurniawati
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

University does not only provide graduates in quantity but also concern about the quality and high discipline,capable of being dinamisator, innovator, motivator and agent of change and to thread high quality of human resources for the various types and levels of expertise. University should care to students’ service quality. University of Nahdlatul Ulama Sidoarjo is a new university in Sidoarjo. This University insists to improve the service quality. Service improvement is expected to affect the students’ satisfaction and trust. So it will be impected on students’ loyalty. The purpose of this study is to identifythe impact of satisfaction level of service quality and trust which are expected to affect the students’ loyalty. The method used in this study is Partial Least Square (PLS), SmartPLS 2.0. The analysis results of existing models shows that service quality has an important role in keeping the students’ loyalty. For students, excellent service will give satisfaction and trust so the loyalty can be risen. Keywords: Service quality, Customer loyalty, Partial Least Square (PLS).

PENGARUH KONSENTRASI SURFAKTAN DAN KECEPATAN PUTAR PENGADUK TERHADAP PROSES PEMISAHAN BITUMEN DARI ASBUTON Nora Amelia Novitrie; Susianto; Ali Altway
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

Asbuton is a rock contain of the bitumen. Asbuton can be used as road construction alternatives after extracting bitumen from the mineral. A method for separating bitumen is separation process using hot water medium. The process was carried out in a stirred tank, 200 grams of asbuton was mixed with diesel oil and added by hot chemical solution (surfactant) in the digestion tank. The separation process in the extractor was made at 900C and time set was 30 minutes. Surfactan concentration and the speed of stirrer were set according to the variable. After the process completed, the mixture was moved into a beaker glass and 500 ml hot water was added. The mixture of diesel oil and bitumen will float in the surface then the density will be measured to determine the bitumen concentration. It can be concluded that concentration of surfactant solution and speed of stirrer have the significant results. The highest recovery percentage of bitumen is 81,99 %. Keywords: Asbuton, Hot water, Speed of stirrer, Surfactant.

PENGEMBANGAN TEKNIK PRODUKSI MASSAL BIOMAS ECENG GONDOK Tatuk Tojibatus Sa’adah; Dwi Haryanta
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

Siltation and the presence of water hyacinth plants on a sewer/river is a cause of flooding in urban areas (beaches). Water hyacinth grows fast in rivers, sewer, boezem, lake and or water storage areas, which impedes the water flow and encourages a silting. Rivers dredging or reservoirs of waste water hyacinths just stacked on the edge of river that makes the dirty environment. The research aims to develop a composting technique made from water hyacinth in a mass scale. Factorial experimental treatments (1) Packaging B1: open, B2: plastic bags (glangsing), and B3: buried; and (2) Starter S1: mixture EM4 30%, S2: mixture EM4 20% + urea 1kg/3 liter, and S3: mixture EM4 10% + urea 2 kg/3 liter, so there are nine treatment combinations. Experimental units are water hyacinth biomass as much as one cubic, nine cubic overall. The research results devoted to volume shrinkage, variable temperature, pH, change in smell, colour and biomass texture of water hyacinth during the first two weeks showed a high variation among treatments, but in the fifth week, all of variables were homogeneous relatively and showed almost complete indicators of composting process. Depreciation amounted to 68-78% volume, temperature 26-29oC, pH of 7.0-7.5; texture is brittle, blackish brown color and relatively odorless. C/N biomass ratio at composting mass of water hyacinth from 33-37, and at fifth week the results are varied for the treatment of S1, S2B1, and S3B1 value is still above 20 while the other is below 20, and the lowest at 16.9 S3B3 treatment. Keywords: Composting technology mass, Water hyacinth biomass, Starter, Packaging

PERANCANGAN PREDIKSI FINANCIAL DISTRESS PADA PERUSAHAAN MANUFAKTUR YANG TERDAFTAR DI BURSA EFEK INDONESIA Rina Sri Wulandari
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

The global economic crisis led many companies especially manufacturing companies be through financial distress. Financial distress is a situation where firms in difficulty conditions before be through bankruptcy. Predictions on the financial conditionimportant by manager, auditors, and investors to make policy decisions. The more accurate the predictions were done, the risk are guaranteed getting smaller either by companies or investors. Therefore, this study aimed to design a prediction model offinancial distress companies listed on the stock exchange Indonesia. This study uses the Data Envelopment Analysis (DEA) method. DEA method used to measure the efficiency of the company. The company that inefficient indicate that the company isthreatened with bankruptcy. Ratios of the company’s financial statements are used as data to be processed using the DEA method. Keywords: Financial distress, Data Envelopment Analysis (DEA), Efficiency.

PEMBUATAN PURWARUPA SISTEM INFORMASI PERSEDIAAN OPTIK STUDI KASUS: UD AGNES, MALANG prasetyo, waluyo
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

UD Agnes/Agnes Optic (AO) was established in 1990 and located at Jalan Imam Bonjol Kota Batu in Malang. This business is engaged in optical products and services. In this study, the research focus is product of eyeglass lenses. OA business development process has faced obstacles in inventory problem and manual restock process. During this time inventory management has not been managed well so it takes a long time to check inventory stock. EOQ method is used to calculate the inventory in gaining restock time and reduce stock inventory searching time so as to produce information about costs and benefits in each period. The result obtained are optimal restock time period for each stock, reduction of searching time inventory, information cost, and the profit obtained by AO. Keywords: Optical Product, Stock, EOQ, Restock.

ATAP DESALINASI SEBAGAI SOLUSI PEMENUHAN KEBUTUHAN AIR BERSIH DI DAERAH PESISIR Ulvi Pri Astuti
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

Seawater or brackish water processing technology to freshwater was known as desalination. Process desalination of evaporation is one of the desalination technique, that effective and economics especially to a coastal area that have larger sun intensity than another. Therefore, in this research will discuss about designing house roof society in coastal region. Tub evaporative and basic tub plate planning size that made for 4,5m x 10m house of floordeck 600 coated with 5,4 cm concrete thick mess. Tub evaporativesize is 3m × 10m × 0,02m. Collective freshwater channel are besides the tub with size 0,75m × 10m. The sketch of roof used easel that made of galvalume profile C 100mm × 50mm × 20mm × 4mm and gording is made of hollow 40mm × 40mm × 0,5mm. Outside cover roof is polytron polycarbonate with 4,2 mm thickness and inside roof fiberglass with 1 mm thickness. Freshwater volume can be produced by tub space 3m × 10m × 0,003m is 89,74 L by seven hours heating process on 485 W/m2 sun intensity. Keywords: Evaporative Desalination, Floordeck 600, Polycarbonate.

ANALISIS SIFAT MEKANIK KOMPOSIT Al 2075 REINFORCEMENT DENGAN ELECTROLESS ABU DASAR BATUBARA Adhi Setiawan; Arita Rochma Nilasari; M. Ari
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

Aluminium composite 2075 manufacturing required a strenghthener such as bottom ash which has been through the electroless plating process that serves coating the bottom ash and sticks to aluminium casting process. The oxidation of 100oC produce 0,0126 µm Mg thickness oxidation, 200oC produce 0,0146 µm Mg thickness oxidation, and 300oC produces 0,0506 µm Mg thickness oxidation. Mechanical properties were tested by using worn-out test and hardness test based on new material function that will be used to replace existing disc brake material. Harness test showed that castings are using oxidized ash powder with higher temperature and produce resistant material than in low temperature. Casting mixture with oxidized bottom ash 100oC produce specific abrasion of 2,008 x 10-6mm2/kg, produce of1,814 x 10-6mm2/kg for oxidized 200oC, and produce of 1,675 x 10-6mm2/kg for oxidized 300oC. Keywords: Aluminium 2075, Bottom ash, Composite, Electroless plating, Hardness test, Worn-out test.

PENGARUH WAKTU DAN TEMPERATUR HIDROLISIS DALAM PROSES SINTESIS FURFURAL DARI SEKAM PADI DENGAN MENGGUNAKAN METODE HIDROLISIS DAN DEHIDRASI Cindi Amborowati; Uni Adriani; Indah Lukyta Aditya; Hanifati Feviasari; Tidar Kumala Hastin; Arief Adhiksana
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

Rice fields in East Kalimantan is one of productive land. It looks from many piles of rice husk waste in rice milling. The rice husk waste has not been used much, so this research used the rice husk waste as raw material of furfural manufacturing. This research has three stages, there are raw material preparation, hydrolysis, and product analysis. At the preparation stage, rice husk is diminished to 100 mesh, then dried in oven. Hydrolysis process used sulfuric acid 1% as catalyst with the variation times were 10, 40, 70, 100, 130 (minutes) and temperature are 30, 50, 70, 90, 105 (°C). Then hydrolysis result was filtered and the filtrate was quantitatively analyzed by volumetric method. Highest result of time variation obtained was at 130 minutes with furfural concentration as much 8,182 mol/L, while highest result of temperature variation obtained was at 105 °C with furfural concentration as much 10,741 mol/L. Keywords: Sulfuric Acid, Furfural, Hydrolysis, Rice Husk.

PENGEMBANGAN PRODUK LAMPU MEJA BELAJAR DENGAN METODE KANO DAN QUALITY FUNCTION DEPLOYMENT (QFD) Aji, Edy Rustam; Yuliawati, Evi
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

The demand for students, college students or office workers to do their study and work require them to sit longer in their study or work place. The place of study must be designed in order to be comfortable, ergonomic, and has aesthetics touches. Study lamp is one of important aspects in study place. Study lamp desi gn has improved in its aspects and function. However, along with its improvement, there are demands of additional function to the existing designs. On that account, this research aims to design and produce the desk lamp with additional functions according to users’ requirement. To realize this aim, Kano and Quality Function Deployment (QFD) methods are applied. The calculation result showed 12 attributes (customer requirements ) and 10 technical parameter priorities were implemented in the design of desk lamp product. The additional functions of this desk lamp are alternating automatic power off between the desk lamp and night lamp whenever one of the lamp not in use, flip design, digital clock, fan, night lamp, cellular phone charger, stationary case, and ability tostay on during the electricity black out. Keywords: Desk Lamp, Kano, Quality Function Deployment (QFD).

ANALISIS PENGENDALIAN KUALITAS PRODUKSI BOGIE BARBER S2HD9C MENGGUNAKAN METODE LEAN SIX SIGMA DI PT BARATA INDONESIA (PERSERO) GRESIK Suparno; Hamim, Moh. Ismail; Prasetiawan, Heru
Journal of Research and Technology Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016
Publisher : 2477 - 6165

This study aimed to analyze the quality control and waste that occurs in side frame S2HD9C production using lean six sigma method with DMAIC approach in PT Barata Indonesia (Persero) Gresik. Side frame S2HD9C is a part of bogie barber S2HD9C products. This study focused on six sigma phase on defect analysis and sigma performance, while lean six sigma phase focused on the analysis of waste and sigma performance. The data used in this study are two types: primary and secondary data, qualitative and quantitative. Primary data were obtained from field observations, while secondary data obtained from the study of the document. This study conducted with the approach of DMAIC (define, measure, analyze, improve, control). After the analysis at six sigma stage, it is known that there are 5 types of defects that occur in January to April 2016, they are trapped gas defect 58.18%, broken core defect 21.82%, sand dropdefect 12.73%, brake mold defect 5.46% and misplace core defect 1.82%. And sigma value achievement level of each defect are as follows: trapped gas defect 1235.71 DPMO = 4.52σ, broken core defect 463.392 DPMO = 4.81σ, sand drop defect 270.312 DPMO = 4.96σ, brake mold defect 115.848 DPMO = 5.18σ and misplace core defect 38.616 DPMO = 5.45σ. In lean six sigma stage, it is known that there are 4 types of waste, they are: waste defect product, waste waiting time (delay), waste transportation, and waste excess process. Here are achievement values of each waste: waste defect product 6890 DPMO = 3.96σ and value capability process 1.31 = 3.94σ, waste waiting time (delay) value capability process 1 = 3σ, waste transportation value capability process 1.31 = 3.94σ and waste excess process 1499.75 DPMO = 4.47σ.Keywords: DPMO, Defects, Lean six sigma, Waste.

Page 1 of 1 | Total Record : 10

Filter by Year

2016 2016

Filter By Issues

All Issue Vol. 11 No. 1 (2025): JRT Volume 11 No 1 Juni 2025 Vol. 10 No. 2 (2024): JRT Volume 10 No 2 Des 2024 Vol. 10 No. 1 (2024): JRT Volume 10 No 1 Juni 2024 Vol. 9 No. 2 (2023): JRT Volume 9 No 2 Des 2023 Vol. 9 No. 1 (2023): JRT Volume 9 No 1 Juni 2023 Vol. 8 No. 2 (2022): JRT Volume 8 No 2 Des 2022 Vol. 8 No. 1 (2022): JRT Volume 8 No 1 Juni 2022 Vol. 7 No. 2 (2021): JRT Volume 7 No 2 Des 2021 Vol. 7 No. 1 (2021): JRT Volume 7 No 1 Jun 2021 Vol. 6 No. 2 (2020): JRT Volume 6 No 2 Des 2020 Vol. 6 No. 1 (2020): JRT Volume 6 No 1 Jun 2020 Vol. 5 No. 2 (2019): JRT Volume 5 No 2 Des 2019 Vol. 5 No. 1 (2019): JRT Volume 5 No 1 Jun 2019 Vol 5, No 2 (2019) Vol 5, No 1 (2019) Vol. 4 No. 2 (2018): JRT Volume 4 No 2 Des 2018 Vol. 4 No. 1 (2018): JRT Volume 4 No 1 Jun 2018 Vol 4, No 2 (2018) Vol 4, No 1 (2018) Vol. 3 No. 2 (2017): JRT Volume 3 No 2 Des 2017 Vol. 3 No. 1 (2017): JRT Volume 3 No 1 Jun 2017 Vol 3, No 2 (2017) Vol 3, No 1 (2017) Vol. 2 No. 2 (2016): JRT Volume 2 No 2 Des 2016 Vol. 2 No. 1 (2016): JRT Volume 2 No 1 Jun 2016 Vol. 2 No. 1 (2016): JRT Volume 1 No 1 Jun 2016 Vol 2, No 2 (2016) Vol 2, No 1 (2016) Vol. 1 No. 1 (2015): JRT Volume 1 No 1 Des 2015 Vol 1, No 01 (2015) More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Muchammad Tamyiz

Contact Email
muchammad_tamyiz@yahoo.com

Phone
-

Journal Mail Official
muchammad_tamyiz@yahoo.com

Editorial Address
-

Location
Kab. sidoarjo,

Jawa timur

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Muchammad Tamyiz

Contact Email muchammad_tamyiz@yahoo.com

Phone -

Journal Mail Official muchammad_tamyiz@yahoo.com

Editorial Address -

Location Kab. sidoarjo, Jawa timur INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Muchammad Tamyiz

Contact Email
muchammad_tamyiz@yahoo.com

Phone
-

Journal Mail Official
muchammad_tamyiz@yahoo.com

Editorial Address
-

Location
Kab. sidoarjo,

Jawa timur

INDONESIA