Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Indonesian Journal of Chemistry

ijc
Website

Published by Universitas Gadjah Mada

ISSN : 14119420 EISSN : 24601578 DOI : -

Core Subject : Science, Engineering,

Chemical Engineering, Chemistry & Bioengineering Chemistry

Indonesian Journal of Chemistry is an International, peer-reviewed, open access journal that publishes original research articles, review articles, as well as short communication in all areas of chemistry including applied chemistry. The journal is accredited by The Ministry of Research, Technology and Higher Education (RISTEKDIKTI) No : 21/E/KPT/2018 (in First Rank) and indexed in Scopus since 2012. Since 2018 (Volume 18), Indonesian Journal of Chemistry publish four issues (numbers) annually (February, May, August and November).

Arjuna Subject : -

Articles 1,981 Documents

74 75 76 77 78

Transport Properties, Mechanical Behavior, Thermal and Chemical Resistance of Asymmetric Flat Sheet Membrane Prepared from PSf/PVDF Blended Membrane on Gauze Supporting Layer Nita Kusumawati; Pirim Setiarso; Maria Monica Sianita; Supari Muslim
Indonesian Journal of Chemistry Vol 18, No 2 (2018)
Publisher : Universitas Gadjah Mada

Asymmetric polysulfone (PSf) membrane is prepared using phase inversion method and blending with polyvinylidene fluoride (PVDF) on the gauze solid support. Casting solution composition optimization has been done to get PSf/PVDF membrane with best characteristics and permeability. The result shows that blending on PSf with PVDF polymer using phase inversion method has been very helpful in creating an asymmetric porous membrane. Increased level of PVDF in casting solution has increased the formation of asymmetry structure and corresponding flux membrane. The result from thermal test using Differential Scanning Calorimetry (DSC)-Thermal Gravimetric Analysis (TGA) shows the resistance of the membrane to temperature 460 °C. Membrane resistance against acid looks from undetectable changes on infrared spectra after immersion process in H2SO4 6–98 v/v%. While membrane color changes from white to brownish and black is detected after the immersion process in sodium hydroxide (NaOH) 0.15–80 w/v%.

Optimization and Validation of an HPLC-UV Method for Determination of Benzoic Acid and Sorbic Acid in Yogurt and Dried-Yogurt Products Using a Design of Experiment Ala Yahya Sirhan
Indonesian Journal of Chemistry Vol 18, No 3 (2018)
Publisher : Universitas Gadjah Mada

A method for the determination and analysis of benzoic acid and sorbic acid in yogurt and dried-yogurt products has been developed. This method was based on the use of a simple solid-liquid extraction method, followed by the high-performance liquid chromatography with a UV detector (HPLC–UV), enhanced with the aid of response surface methodology and design of experiment (DOE). The method excludes the use of complicated procedures, time-consuming and labor-intensive pre-treatment processes. Separation of the benzoic acid and sorbic acid with higher selectivity and sensitivity, and within reasonable retention time was performed by using an isocratic mobile phase of acetate buffer (pH 5.6)-methanol 60:40 at a column temperature of 25 °C. Optimization of sample preparation and analytical conditions gave recoveries in the range of 81 to 111% at spike levels of 2–20 mg/L and the relative standard deviations (RSDs) was lower than 9% in all cases. The intra-day precision and inter-day precision results were in the range of 8.4–8.5% and 10.4–11.0%. Additionally, the limits of detection (LOD) were 0.66 and 0.51 mg/L and the limits of quantification (LOQ) were 1.3 and 1.0 mg/L for benzoic acid and sorbic acid, respectively.

QMCF-MD Simulation and NBO Analysis of K(I) Ion in Liquid Ammonia Yuniawan Hidayat; Ria Armunanto; Harno Dwi Pranowo
Indonesian Journal of Chemistry Vol 18, No 2 (2018)
Publisher : Universitas Gadjah Mada

Ab initio of Quantum Mechanics Charge Field Molecular Dynamic (QMCF-MD) of K(I) ion in liquid ammonia has been studied. A Hartree-Fock level of theory was coupled with LANL2DZ ECP basis set for K(I) ion and DZP (Dunning) for ammonia. Two regions as first and second solvation shell were observed. In the first solvation shell at distance 3.7 (Å), K(I) ion was coordinated by four to eight ammonia molecules dominated by K(NH3)6+ species. Second shell of solvation was ranging between 3.7 Å to 7.3 Å. Within simulation time of 20 ps, the frequent exchange processes of ligands indicating for a very labile solvation structure. Four mechanism types of ligand exchange between first and second solvation shell were observed. Mean residence time of ligand is less than 2 ps confirming weak in ion-ligand interaction. Evaluation of K(NH3)6+ using natural bond orbital analysis shows that the Wiberg bond Index is less than 0.05 indicating weak electrostatic interaction of K-N.

Incorporation of Poly(Vinyl Alcohol) for The Improved Properties of Hydrothermal Derived Calcium Phosphate Cements Nurul Nabilah Razali; Iis Sopyan
Indonesian Journal of Chemistry Vol 18, No 2 (2018)
Publisher : Universitas Gadjah Mada

Calcium phosphate cement (CPC) has been synthesized via a straightforward hydrothermal route. Calcium oxide and ammonium dihydrogen phosphate were used as calcium and phosphate precursors. The precursors were refluxed in distilled water at 90–100 °C and dried overnight until the calcium phosphate powder was formed. CPC was then produced by mixing the powder and distilled water at the powder-to-liquid (P/L) ratio of 1.5. Poly(vinyl alcohol) (PVA) of 1 to 7% (w/w) was added and its effect on physical properties was investigated. It was proved that PVA addition up to 7% (w/w) has shortened the setting time but decreased the injectability. The PVA free CPC has the initial and final setting times of 71 and 187 min, respectively and the injectability of 99.92%. The compressive strength also increased with the amount of PVA added in CPC. In addition, soaking CPC in Ringer's solution for 7, 14 and 21 days also gave remarkable effects on cohesion, microstructure and mechanical properties of the cement.

Simultaneous Analysis of 6-Mercaptopurine, 6-Methylmercaptopurine, and 6-Thioguanosine-5’-monophosphate in Dried Blood Spot Using Ultra Performance Liquid Chromatography Tandem Mass Spectrometry Supandi Supandi; Yahdiana Harahap; Harmita Harmita; Rizka Andalusia
Indonesian Journal of Chemistry Vol 18, No 3 (2018)
Publisher : Universitas Gadjah Mada

6-Mercaptopurine is a chemotherapeutic agent of the antimetabolite class. This study aims to analyze simultaneous validation of 6-mercaptopurine (6-MP), 6-methylmercaptopurine (6-MMP), and 6-thioguanosine-5’-monophosphate (6-TGMP) in dried blood spot (DBS) using ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). An accurate volume of 60 μL blood was spotted onto DBS-CAMAG paper and then extracted using methanol 90% (v/v) containing an internal standard of 5-fluorouracil (5-FU). Separation was performed using a Waters Acquity UPLC BEH AMIDA column 1.7 μm (2.1 x 100 mm) with a mobile phase mixture of 0.2% (v/v) formic acid in water−0.1% (v/v) formic acid in acetonitrile-methanol with gradient elution and flow rate of 0.2 mL/min. Mass detection was done using Waters Xevo TQD with positive electrospray ionization (ESI) for 6-MP, 6-MMP, 6-TGMP and negative ESI for 5-FU, in multiple reaction monitoring mode. Detection rates of 6-MP, 6-MMP, 6-TGMP and 5-FU were m/z 153.09 > 119.09; 167.17 > 126.03; 380.16 > 168.00); 129.09 > 42.05, respectively. This method is linear across the range 25.5–1020 ng/mL for 6-MP, 6-MMP and 6-TGMP. This method is valid for the in vitro simultaneous analysis of 6-MP, 6-MMP and 6-TGMP in DBS, based on European Medicine Agency guidelines.

Analytical Method Validation and Determination of Free Drug Content of 4-n-Butylresorcinol in Complex Lipid Nanoparticles Using RP-HPLC Method Rini Dwiastuti; Marchaban Marchaban; Enade Perdana Istyastono; Florentinus Dika Octa Riswanto
Indonesian Journal of Chemistry Vol 18, No 3 (2018)
Publisher : Universitas Gadjah Mada

Lipid nanoparticles, one of nanoparticle technology results has been developed both as a drug delivery system and as a research object. Complex lipid nanoparticle, in the drug delivery system development, has an advantage due to its less toxicity. It is important to develop a validated analytical method to determine the drug content in the system of nanoparticle lipid. This research aimed to develop a valid RP-HPLC method to determine free drug content of 4-n-butylresorcinol in the liposome matrix followed by the determination of the encapsulation efficiency (EE%). A system of the RP-HPLC method has been developed using a column of C18 and methanol-redistilled water-glacial acetic acid 79:20:1 (v/v) as the mobile phase with pH maintained at 2.1–2.6. This method was validated in the parameters of selectivity, sensitivity, linearity, accuracy, and precision. During 30 days of storage, the complex lipid nanoparticle system showed the increase in the EE% value during storage time.

Isolation, Cellulase Activity Test and Molecular Identification of Selected Cellulolytic Bacteria Indigenous Rice Bran Akyunul Jannah; Aulanni`am Aulanni`am; Tri Ardyati; Suharjono Suharjono
Indonesian Journal of Chemistry Vol 18, No 3 (2018)
Publisher : Universitas Gadjah Mada

Rice bran is the waste product of rice milling which is abundant in Indonesia, it can be used as a raw material for the manufacture of bioethanol by fermentation. Before being fermented, rice bran must be hydrolyzed into glucose by biomass degrading. This study was aimed to isolate indigenous cellulolytic bacteria from rice bran as producer of cellulolytic enzymes and resulted in 22 bacterial isolates that demonstrated cellulolytic activity being identified. Among them, BE 8 and BE 14 isolates showed the highest endoglucanase activity at 2.16 and 1.31 U/mL respectively. Identification of the 16S rDNA showed that BE 8 belongs to Bacillus subtilis and BE 14 in Bacillus cereus.

Removal Efficiency of Nitrite and Sulfide Pollutants by Electrochemical Process by Using Ti/RuIrO2 Anode Aris Mukimin; Agus Purwanto
Indonesian Journal of Chemistry Vol 18, No 2 (2018)
Publisher : Universitas Gadjah Mada

In general, wastewater treatment by physical, chemical and biological methods are only focused on TSS, BOD and COD removals that the effluent still contains anion pollutant as NO2- and S2-. Electrochemical technology is a proper method for those pollutants treatment due to its fast process, easy operation and minimum amount of sludge. Electrocatalytic reactor with 8 L capacity using Ti/RuIrO2 cylinder as anode and Fe plate as cathode was arranged and applied to treat anion pollutants. Hydraulic retention time (30, 60, 90 and 120 min), salt concentration (250, 500 and 750 mg/L) and voltage (4, 5, and 6 V) were chosen as operation variables and NO2- and S2- concentrations as parameter indicators. Nitrite removal efficiency reached 75 and 99.7% after 60 and 120 min of electrolysis, respectively, while sulfide could obtain higher efficiency, i.e., 97 and 99.9% after 60 and 90 min, respectively, at operation variables of potential of 5 V and salt of 500 mg/L. Removal process is dominated by indirect oxidation mechanism by HClO/ClO- oxidators generated at anode surface as intermediate products. The lifespan of electrode and electric consumption are two main factors of operation cost. Electric consumed was 0.452 kWh per 1 g nitrite removed.

Ag/AgCl Reference Electrode Based on Thin Film of Arabic Gum Membrane Sagir Alva; Aiman Sajidah binti Abdul Aziz; Mohd Ismahadi bin Syono; Wan Adil bin Wan Jamil
Indonesian Journal of Chemistry Vol 18, No 3 (2018)
Publisher : Universitas Gadjah Mada

The Ag/AgCl reference electrode based on the Arabic Gum (AG) hydrogel films was successfully developed. The Arabic Gum concentration used in this study was 10–40% (w/v) with an optimum concentration of 20% (w/v). In this study, reference electrode performance testing is based on DmV response of Cl-ion’s measurements, stability tests and performance testing against ISE sensors such as K+, NH4+, and NO3-. The Ag/AgCl based reference electrode of the Arabic Gum film shows an average DmV of 4.0 ± 0.7 mV when response test is performed against a standard Ag/AgCl double junction electrode in various concentrations of Cl-ion’s. Meanwhile, in stability testing conducted in a 0.01 M KCl solution for 72 h found drift of < 0.6 mV/h. The reference performance test of the Arabic Gum reference electrode with three types of ISE NH4+, K+ and NO3- commercial sensors obtaining a slope closer to the Nernst value is 54.9 ± 0.9, 52.3 ± 0.5 and -53.2 ± 0.2 mV/dec with all having a linear distance of 0.1–10-5 M.

Desorption and Re-Adsorption of Procion Red MX-5B Dye on Alumina-Activated Carbon Composite Fatma Fatma; Poedji Loekitowati Hariani; Fahma Riyanti; Wiwin Sepriani
Indonesian Journal of Chemistry Vol 18, No 2 (2018)
Publisher : Universitas Gadjah Mada

The alumina-activated carbon has the ability to adsorb and desorb the procion red MX-5B. The research evaluated the influence of desorption agent, contact time, and temperature on desorption process of procion red MX-5B dye with alumina-activated carbon composite and the adsorption capacity of the composite after desorption process. The desorption agents used in desorption process were solution with pH 2−10, H2O2 30 % (v/v), methanol 70% (v/v) and ethanol 70% (v/v). The variation of contact time was in the range from 30 to 270 min and the temperature was set between 30−75 °C. The result concluded that the highest desorption efficiency up to 98.56% was achieved using ethanol 70% (v/v) for 240 min at 45 °C. The desorption kinetic followed the pseudo-first-order with the release constant (kdes) of 6.56 × 10-2 min-1. The SEM micrograph showed there is a more porous surface on the composite after the desorption compared to before the desorption. The EDX analysis indicated that alumina content in the composite was reduced after desorption process. FTIR spectra of the composite before and after desorption process showed a peak of Al−O at 592 and 590 cm-1 which was proved that alumina still exists in the composite after the desorption process. The alumina-activated carbon composite was re-used to adsorb procion red MX-5B dye. After three times of desorption and re-adsorption process, the capacity adsorption was decreased from 12.38 to 7.38 mg/g.

Page 76 of 199 | Total Record : 1981

74 75 76 77 78

Filter by Year

2001 2026

Filter By Issues

All Issue Vol 26, No 1 (2026) Vol 25, No 5 (2025) Vol 25, No 4 (2025) Vol 25, No 3 (2025) Vol 25, No 2 (2025) Vol 25, No 1 (2025) Vol 24, No 6 (2024) Vol 24, No 5 (2024) Vol 24, No 4 (2024) Vol 24, No 3 (2024) Vol 24, No 2 (2024) Vol 24, No 1 (2024) Vol 23, No 6 (2023) Vol 23, No 5 (2023) Vol 23, No 4 (2023) Vol 23, No 3 (2023) Vol 23, No 2 (2023) Vol 23, No 1 (2023) Vol 22, No 6 (2022) Vol 22, No 5 (2022) Vol 22, No 4 (2022) Vol 22, No 3 (2022) Vol 22, No 1 (2022) Vol 22, No 2 (2022) Vol 21, No 6 (2021) Vol 21, No 5 (2021) Vol 21, No 4 (2021) Vol 21, No 3 (2021) Vol 21, No 2 (2021) Vol 21, No 1 (2021) Vol 20, No 6 (2020) Vol 20, No 5 (2020) Vol 20, No 4 (2020) Vol 20, No 3 (2020) Vol 20, No 2 (2020) Vol 20, No 1 (2020) Vol 19, No 4 (2019) Vol 19, No 3 (2019) Vol 19, No 2 (2019) Vol 19, No 1 (2019) Vol 18, No 4 (2018) Vol 18, No 3 (2018) Vol 18, No 2 (2018) Vol 18, No 1 (2018) Vol 17, No 3 (2017) Vol 17, No 2 (2017) Vol 17, No 1 (2017) Vol 16, No 3 (2016) Vol 16, No 2 (2016) Vol 16, No 1 (2016) Vol 15, No 3 (2015) Vol 15, No 2 (2015) Vol 15, No 1 (2015) Vol 14, No 3 (2014) Vol 14, No 2 (2014) Vol 14, No 1 (2014) Vol 13, No 3 (2013) Vol 13, No 2 (2013) Vol 13, No 1 (2013) Vol 12, No 3 (2012) Vol 12, No 2 (2012) Vol 12, No 1 (2012) Vol 11, No 3 (2011) Vol 11, No 2 (2011) Vol 11, No 1 (2011) Vol 10, No 3 (2010) Vol 10, No 2 (2010) Vol 10, No 1 (2010) Vol 9, No 3 (2009) Vol 9, No 2 (2009) Vol 9, No 1 (2009) Vol 8, No 3 (2008) Vol 8, No 2 (2008) Vol 8, No 1 (2008) Vol 7, No 3 (2007) Vol 7, No 2 (2007) Vol 7, No 1 (2007) Vol 6, No 3 (2006) Vol 6, No 2 (2006) Vol 6, No 1 (2006) Vol 5, No 3 (2005) Vol 5, No 2 (2005) Vol 5, No 1 (2005) Vol 4, No 3 (2004) Vol 4, No 2 (2004) Vol 4, No 1 (2004) Vol 3, No 3 (2003) Vol 3, No 2 (2003) Vol 3, No 1 (2003) Vol 2, No 3 (2002) Vol 2, No 2 (2002) Vol 2, No 1 (2002) Vol 1, No 3 (2001) Vol 1, No 2 (2001) Vol 1, No 1 (2001) Article in press ARTICLE IN PRESS More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kab. sleman,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kab. sleman, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kab. sleman,

Daerah istimewa yogyakarta

INDONESIA