Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

International Journal of Electrical and Computer Engineering

IJECE
Website

Published by Institute of Advanced Engineering and Science

ISSN : 20888708 EISSN : 27222578 DOI : -

Core Subject : Science, Engineering,

Computer Science & IT Electrical & Electronics Engineering

International Journal of Electrical and Computer Engineering (IJECE, ISSN: 2088-8708, a SCOPUS indexed Journal, SNIP: 1.001; SJR: 0.296; CiteScore: 0.99; SJR & CiteScore Q2 on both of the Electrical & Electronics Engineering, and Computer Science) is the official publication of the Institute of Advanced Engineering and Science (IAES). The journal is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world.

Arjuna Subject : Ilmu Komputer (semua kategori) - Ilmu Komputer (Lain-Lain)

Articles 6,301 Documents

225 226 227 228 229

Circularly Polarized Cylindrical Dielectric Resonator Antenna with Different Shapes Cross Slot Zahra Rahimian
International Journal of Electrical and Computer Engineering (IJECE) Vol 4, No 6: December 2014
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (354.122 KB)

A cross slot coupled cylindrical dielectric resonator antenna (CDRA) operating in the X-band (8GHz -12GHz) frequency range is studied. The proposed CP designs are achieved by implementing a suitable cross slot on the ground plane (in the case of aperture coupled feed method), which results in excitation of two near degenerate orthogonal modes of near equal amplitudes and 90°phase difference. Attempts are made to change the geometry of slots ends to introduce a novel structure in order to achieve a better impedance bandwidth with an improved 3dB axial ratio (AR) bandwidth. It is found that the hourglass of cross slot has a great effect on the strength of coupling between the feed line and the dielectric resonator antenna. In simulation an impedance bandwidth of 46.15% and axial ratio bandwidth of 22% has been achieved with the above geometry. An improvement of 12% in impedance bandwidth and 11.2% in Axial ratio bandwidth is obtained over conventional rectangular cross slot.DOI:http://dx.doi.org/10.11591/ijece.v4i6.6484

Adapted Branch-and-Bound Algorithm Using SVM With Model Selection Mohamed Mustapha Kabbaj; El Afia Abdellatif
International Journal of Electrical and Computer Engineering (IJECE) Vol 9, No 4: August 2019
Publisher : Institute of Advanced Engineering and Science

Branch-and-Bound algorithm is the basis for the majority of solving methods in mixed integer linear programming. It has been proving its efficiency in different fields. In fact, it creates little by little a tree of nodes by adopting two strategies. These strategies are variable selection strategy and node selection strategy. In our previous work, we experienced a methodology of learning branch-and-bound strategies using regression-based support vector machine twice. That methodology allowed firstly to exploit information from previous executions of Branch-and-Bound algorithm on other instances. Secondly, it created information channel between node selection strategy and variable branching strategy. And thirdly, it gave good results in term of running time comparing to standard Branch-and-Bound algorithm. In this work, we will focus on increasing SVM performance by using cross validation coupled with model selection.

Performance Evaluation of Quarter Shift Dual Tree Complex Wavelet Transform Based Multifocus Image Fusion Using Fusion rules Radha N.; T.Ranga Babu
International Journal of Electrical and Computer Engineering (IJECE) Vol 9, No 4: August 2019
Publisher : Institute of Advanced Engineering and Science

In this paper, multifocus image fusion using quarter shift dual tree complex wavelet transform is proposed. Multifocus image fusion is a technique that combines the partially focused regions of multiple images of the same scene into a fully focused fused image. Directional selectivity and shift invariance properties are essential to produce a high quality fused image. However conventional wavelet based fusion algorithms introduce the ringing artifacts into fused image due to lack of shift invariance and poor directionality. The quarter shift dual tree complex wavelet transform has proven to be an effective multi-resolution transform for image fusion with its directional and shift invariant properties. Experimentation with this transform led to the conclusion that the proposed method not only produce sharp details (focused regions) in fused image due to its good directionality but also removes artifacts with its shift invariance in order to get high quality fused image. Proposed method performance is compared with traditional fusion methods in terms of objective measures.

Enlarge Medical Image using Line-Column Interpolation (LCI) Method Jufriadif Na'am; Julius Santony; Yuhandri Yuhandri; Sumijan Sumijan; Gunadi Widi Nurcahyo
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 5: October 2018
Publisher : Institute of Advanced Engineering and Science

Quality of medical image has an important role in constructing right medical diagnosis. This paper recommends a method to improve the quality of medical images by increasing the size of the image pixels. By increasing the size of pixels, the size of the objects contained therein is also greater, making it easier to observe. In this study medical images of Brain CT-Scan, Chest X-Ray and Panoramic X-Ray were processed using Line-Column Interpolation (LCI) Method. The results of the treatment are then compared to Nearest Neighbor Interpolation (NNI), Bilinear Interpolation (BLI) and Bicubic Interpolation (BCI) processing results. The experiment shows that Line-Column Interpolation Method produces a larger image with details of the objects in it are not blurred and has equal visual effects. Thus, this method is expected to be a reference material in enlarging the size of the medical image for ease in clinical analysis.

Projectile velocity control on coilgun using genetic algorithms Basuki Winarno; Rakhmad Gusta Putra; Indarto Yuwono; Bambang Sumantri; Agus Indra Gunawan
International Journal of Electrical and Computer Engineering (IJECE) Vol 9, No 6: December 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (952.351 KB)

Multistage Coilgun is an electromagnetic coil composed of more than one coil so that can throw a projectile. The velocity of the projectile coming out of the tube must be controlled. The mechanism can be done by a multistage coilgun design that has a varying number of turns. Each coil that coincides with one another is wrapped separately. The motion of projectile following the velocity profile is perfomed by designing a multistage coil in different layer number based on the energy needed, and therefore the coil is more efficient. Furthermore, the velocity of the projectile is controlled by controlling the current injected to the coil using the Genetic Algorithm method. A prototype of a multistage coilgun system with the proposed coil variation is built in this work. The test is carried out 7 times with an average final velocity of the projectile of 29,89 m/s. While the results of the numerical simulation are 32,63 m/s. Testing error compared to simulation is 9,15%.

Design and Development of a Shortwave near Infrared Spectroscopy using NIR LEDs and Regression Model Kim Seng Chia; Yit Peng Tan
International Journal of Electrical and Computer Engineering (IJECE) Vol 7, No 6: December 2017
Publisher : Institute of Advanced Engineering and Science

Near infrared (NIR) spectroscopic technology has been getting more attention in various fields. The development of a low cost NIR spectroscopy is crucial to reduce the financial barriers so that more NIR spectroscopic applications will be investigated and developed by means of the NIR spectroscopic technology. This study proposes an alternative to measure shortwave NIR spectrum using one collimating lens, two slits, one NIR transmission grating, one linear array sensor, and one microcontroller. Five high precision narrow bands NIR light emitting diodes (LEDs) were used to calibrate the proposed spectroscopy. The effects of the proposed two slits design, the distance between the grating and linear array sensor, and three different regression models were investigated. The accuracy of the proposed design was cross-validated using leave-one-out cross-validation. Results show that the proposed two slits design was able to eliminate unwanted signals substantially, and the cross-validation was able to estimate the best model with root mean squared error of cross-validation of 3.8932nm. Findings indicate that the cross-validation approach is a good approach to estimate the final model without over-fitting, and the proposed shortwave NIR spectroscopy was able to estimate the peak value of the acquired spectrum from NIR LEDs with RMSE of 1.1616nm.

Hybrid energy storage system optimal sizing for urban electrical bus regarding battery thermal behavior Si Mohamed Faresse; Mohamed Assini; Abdallah Saad
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 3: June 2020
Publisher : Institute of Advanced Engineering and Science

This paper proposes an algorithm for sizing the hybrid energy storage system of an urban electrical bus regarding battery thermal behavior. The aim of this study is to get the supercapacitors optimal contribution part in the hybrid energy storage system to keep the battery temperature within its allowable limit. A semi-active parallel topology that uses supercapacitors as a main source of energy is considered. According to the bus mechanical parameters and the ARTEMIS driving cycle, the power and energy demand are calculated. Using mathematical models for the battery, supercapacitors and DC-DC converter, several simulations are performed for different hybridization percentages. While observing the evolution of battery temperature, the most favorable hybridization percentage is defined.

Single view vs. multiple views scatterplots Federico Manuri; Andrea Sanna; Fabrizio Lamberti
International Journal of Electrical and Computer Engineering (IJECE) Vol 9, No 2: April 2019
Publisher : Institute of Advanced Engineering and Science

Among all the available visualization tools, the scatterplot has been deeply analyzed through the years and many researchers investigated how to improve this tool to face new challenges. The scatterplot visualization diagram is considered one of the most functional among the variety of data visual representations, due to its relative simplicity compared to other multivariable visualization techniques. Even so, one of the most significant and unsolved challenge in data visualization consists in effectively displaying datasets with many attributes or dimensions, such as multidimensional or multivariate ones. The focus of this research is to compare the single view and the multiple views visualization paradigms for displaying multivariable dataset using scatterplots. A multivariable scatterplot has been developed as a web application to provide the single view tool, whereas for the multiple views visualization, the ScatterDice web app has been slightly modified and adopted as a traditional, yet interactive, scatterplot matrix. Finally, a taxonomy of tasks for visualization tools has been chosen to define the use case and the tests to compare the two paradigms.

An Infrared-Aided Lighting Control System For Physically Impaired Omotosho Oludayo Hannah; Michael O. Kolawole
International Journal of Electrical and Computer Engineering (IJECE) Vol 3, No 5: October 2013
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (203.18 KB)

In recent years the need to provide greater convenience for the physically impaired community is a challenging issue: the reason being that more reliable and cost effective system are required. This paper proposes a cost effective infrared-based solution for automatic control of electrical circuitry and systems in a residential building to aid easy access for physically impaired and/or elderly people. This electronic system has been designed to meet the need of users such that it switches ON the lighting circuits on the detection of entry into a room and switches OFF the circuit as soon as the room is empty. One of the most important features of this design is the ability to automatically adjust the power consumption on the basis of human presence in a room. The device is simple both in its functionality and implementation.DOI:http://dx.doi.org/10.11591/ijece.v3i5.3627

Low Noise Amplifier using Darlington Pair At 90nm Technology Rashmi Singh; Rajesh Mehra
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 4: August 2018
Publisher : Institute of Advanced Engineering and Science

The demand of low noise amplifier (LNA) has been rising in today’s communication system. LNA is the basic building circuit of the receiver section satellite. The design concept demonstrates the design trade off with NF, gain, power consumption. This paper reports on with analysis of wideband LNA. This paper shows the schematic of LNA by using Darlington pair amplifier. This LNA has been fabricated on 90nm CMOS process. This paper is focused on to make comparison of three stage and single stage LNA. Here, the phase mismatch between these patameters is quantitavely analyzed to study the effect on gain and noise figure (NF). In this paper, single stage LNA has shown the 23 dB measured gain, while the three stages LNA has demonstrated 29 dB measured gain. Here, LNA designed using darlington pair shows low NF of 3.3-4.8 dB, which comparable to other reported single stage LNA designs and appreciably low compared to the three stages LNA. Hence, findings from this paper suggest the use of single stage LNA designed using Darlington pair in transceiver satellite applications.

Page 227 of 631 | Total Record : 6301

225 226 227 228 229

Filter by Year

2011 2026

Filter By Issues

All Issue Vol 16, No 1: February 2026 Vol 15, No 6: December 2025 Vol 15, No 5: October 2025 Vol 15, No 4: August 2025 Vol 15, No 3: June 2025 Vol 15, No 2: April 2025 Vol 15, No 1: February 2025 Vol 14, No 6: December 2024 Vol 14, No 5: October 2024 Vol 14, No 4: August 2024 Vol 14, No 3: June 2024 Vol 14, No 2: April 2024 Vol 14, No 1: February 2024 Vol 13, No 6: December 2023 Vol 13, No 5: October 2023 Vol 13, No 4: August 2023 Vol 13, No 3: June 2023 Vol 13, No 2: April 2023 Vol 13, No 1: February 2023 Vol 12, No 6: December 2022 Vol 12, No 5: October 2022 Vol 12, No 4: August 2022 Vol 12, No 3: June 2022 Vol 12, No 2: April 2022 Vol 12, No 1: February 2022 Vol 11, No 6: December 2021 Vol 11, No 5: October 2021 Vol 11, No 4: August 2021 Vol 11, No 3: June 2021 Vol 11, No 2: April 2021 Vol 11, No 1: February 2021 Vol 10, No 6: December 2020 Vol 10, No 5: October 2020 Vol 10, No 4: August 2020 Vol 10, No 3: June 2020 Vol 10, No 2: April 2020 Vol 10, No 1: February 2020 Vol 9, No 6: December 2019 Vol 9, No 5: October 2019 Vol 9, No 4: August 2019 Vol 9, No 3: June 2019 Vol 9, No 2: April 2019 Vol 9, No 1: February 2019 Vol 8, No 6: December 2018 Vol 8, No 5: October 2018 Vol 8, No 4: August 2018 Vol 8, No 3: June 2018 Vol 8, No 2: April 2018 Vol 8, No 1: February 2018 Vol 7, No 6: December 2017 Vol 7, No 5: October 2017 Vol 7, No 4: August 2017 Vol 7, No 3: June 2017 Vol 7, No 2: April 2017 Vol 7, No 1: February 2017 Vol 6, No 6: December 2016 Vol 6, No 5: October 2016 Vol 6, No 4: August 2016 Vol 6, No 3: June 2016 Vol 6, No 2: April 2016 Vol 6, No 1: February 2016 Vol 5, No 6: December 2015 Vol 5, No 5: October 2015 Vol 5, No 4: August 2015 Vol 5, No 3: June 2015 Vol 5, No 2: April 2015 Vol 5, No 1: February 2015 Vol 4, No 6: December 2014 Vol 4, No 5: October 2014 Vol 4, No 4: August 2014 Vol 4, No 3: June 2014 Vol 4, No 2: April 2014 Vol 4, No 1: February 2014 Vol 3, No 6: December 2013 Vol 3, No 5: October 2013 Vol 3, No 4: August 2013 Vol 3, No 3: June 2013 Vol 3, No 2: April 2013 Vol 3, No 1: February 2013 Vol 2, No 6: December 2012 Vol 2, No 5: October 2012 Vol 2, No 4: August 2012 Vol 2, No 3: June 2012 Vol 2, No 2: April 2012 Vol 2, No 1: February 2012 Vol 1, No 2: December 2011 Vol 1, No 1: September 2011 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Tole Sutikno

Contact Email
ijece@iaesjournal.com

Phone
-

Journal Mail Official
ijece@iaesjournal.com

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Tole Sutikno

Contact Email ijece@iaesjournal.com

Phone -

Journal Mail Official ijece@iaesjournal.com

Editorial Address -

Location Kota yogyakarta, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Tole Sutikno

Contact Email
ijece@iaesjournal.com

Phone
-

Journal Mail Official
ijece@iaesjournal.com

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA