Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Logic : Jurnal Rancang Bangun dan Teknologi

LOGIC
Website

Published by Politeknik Negeri Bali

ISSN : 1412114X EISSN : 25805649 DOI : -

Core Subject : Science, Education,

Computer Science & IT Education

Logic : Jurnal Rancang Bangun dan Teknologi is a peer-reviewed research journal aiming at promoting and publishing original high quality research in all disciplines of engineering and applied technology. All research articles submitted to Logic should be original in nature, never previously published in any journal or presented in a conference or undergoing such process across the world. All the submissions will be peer-reviewed by the panel of experts associated with particular field. Submitted papers should meet the internationally accepted criteria and manuscripts should follow the style of the journal for the purpose of both reviewing and editing.

Arjuna Subject : -

Articles 8 Documents

Search results for , issue "Vol 19 No 1 (2019): March" : 8 Documents clear

Analysis of the Effect of Temperature on Tire's Durability on Engkel Truck Vehicle Wayan Suastawa; Ida Bagus Putu Sukadana
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

Tires are a very important component of a vehicle, a variety of charges are imposed on the tires when the vehicle is stationary or moving. The various loading styles directly rest on the air trapped in the tire, and cause the rise of pressure to flow in accordance with the magnitude of the various forces it receives. The rise in tire pressure mainly occurs when the vehicle is in motion, where the tire gets a compressive force from the constant load of the vehicle and the shock load due to the road contour. High pressure and rising and falling causes heat on the tire which then heat is moved to the rubber tire layer. Besides also because of the heat when the surface of the tire tread rub against the road during acceleration and braking. Assuming that heat is the main cause of tire damage then this study will try to analyze the influence of tire rubber temperature on the ability of work to withstand the air pressure in the tire. The loading received by the tire rubber coating is assumed to be the same as the tensile test that will be applied to the tire when used. This tensile test will be carried out on the rubber tire layer by heat treatment before it is tested. Temperature treatment starts from a temperature of 30 until 110 with a range of 20 degrees, with the expected stress value and the best strain obtained at that temperature range. The tire samples used in this study are two of the most used tire brands on ankle truck trucks which are the most widely used truck types. With tensile test the tire performance is generally very good at low temperature up to 70 degree temperature, above 70 degree temperature tire performance began to decrease due to the increased strain on the tire material so that the ability to resist high pressure by the pneumatic force of the wind inside the tire decreased relative Against the increase in tire temperature.

Tellurium Effect on ASTM A 220 Graphite Malleable Cast Iron Mohammad Nur Hidajatullah; Achmad Sambas; Khansa Sarah Puspita
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

The result of investigation of tellurium malleable cast iron are presented in the paper. Various small quantity of tellurium are added in the ladle before pouring molten metal. The main aim of investigation was determination of the influence composition of tellurium on graphite microstructure and mechanical properties. In addition, the final mechanical property of composition determined by hardness measurements. The favourable influence of the addition of tellurium into malleable cast iron molten metal on the tested properties after annealing as well as an percentation of graphite structure from 2% up to 6.5% and increase hardness from 38 HRc up to 43 HRc

Error Optimization in Electrical Power Quality Monitoring Data Isdawimah Isdawimah
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

In the application of electrical power quality control, the necessity for data processing becomes very important. The measurement data obtained is the latest data and measured in real time with good time resolution and with low error. The object of research is the quality of electric power, the research is about ways of measuring quality of electrical power to obtain accurate data in accordance with actual conditions. This method is capable of measuring data of electrical power quality that changes very quickly with a low error. This data is used as a basis for improving the quality of electric power accurately and accurately.

Ground Fault Protection Using Open Break Delta Grounding Transformer in Ungrounded System Supriyanto Suhono; Hari Purnama; Heri Budi Utomo
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

One of the most common and difficult problems to solve in distribution power systems is the location and elimination of the ground fault. For the study of an electrical distribution network in ungrounded system operating at 20 kV on the primary and 380 V on the secondary. The model uses smaller nominal voltages consisting of 380 V on the primary and the secondary. The Ground fault protection system scheme uses over voltage relays and open break delta transformers, whereas for fault location detection using voltage transformers in star star connections.The highest single line to ground fault value is used for consideration of ballast rating selection. The single line to lowest ground fault value is used for setting the threshold on the voltage relay (59N). Referring to the result of the calculation of the highest single phase to ground voltage at point 1 is 144∠1800 volts, and the lowest point at 4 is 132∠1800 volts. A 200 ohm ballast impedance with 150 watts of power capacity, and an overvoltage threshold setting of 120 volts with TDS of 40. One phase fault protection mechanism works well at each point of interference, and voltage transformers are protected from overheating and damage.

Redesign of Clove Dryer Simulation Machine Using Heat Waste of Radiator as the Heat Source I Kadek Ervan Hadi Wiryanta
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

In this study, a redesign to a clove dryer simulation tool using exhaust heat from radiator as a source of heat energy has been done. The dryer simulation tool consists of reservoir tank, a heater, a pump to circulate the water in the system, a radiator as a heat exchanger and a drying chamber with 2 shelves. The redesign stage is carried out by fixing the piping insulation system, changing the pipe and adding valve controls to vary the velocity of the fluid flow. Variations made are variations in the mass flow rate of 0.09 kg / s and 0.18 kg /s with a constant air flow rate of 1 m/s. The results of the analysis show that at a higher mass flow rate of 0.18 kg/s the average rate of heat transfer from the radiator air side is higher, which is around 3971.65 watts. The effectiveness of the radiator will also be higher at a higher mass flow rate, the average is 0.34 at a mass flow rate of 0.09 kg/s and 0.43 at a mass flow rate of 0.18 kg /s. For drying rates with a load of 2 kg of cloves with a higher flow rate of liquid will be faster, which is about 5 hours with a flow rate of 0.18 kg/s and 6.5 hours at a flow rate of 0.09 kg/s

Design and Development of Login Security System Using Radio Frequency Identification I Gede Sujana Eka Putra; Ni Luh Putu Labasariyani
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

System security is important in information systems to prevent unauthorized users from accessing data. Login system applies security using encrypted passwords stored on RFID cards. This research designed login security system storing encrypted password using MD5 encryption into the Mifare Tag RFID card and equipped NFC reader to read data from RFID Card. By storing encrypted password characters on RFID cards, login system security is stronger and cannot be traced by unauthorized parties to log into systems. Some stage of system design are through study of literature, designing process flow, system algorithms, designing encryption methods and system interfaces, writing card module coding, card reading module coding, implementation, and system testing. The system login applied by scanning RFID card on the NFC reader, if the password on RFID matches then the user successfully logs into the system. Based on the testing of RFID Tag readings, the maximum distance from the reading of RFID Tag cards is up to 7 cm with a reading range of 00 to 300 with a success rate of 100% authentication. By using RFID Tag cards, increase security for logging into the system, because user cannot log in without having a card with the appropriate password.

Design of Ergonomic Work Desk for Workbench Practicum Kurnia Dwi Artika; Rusuminto Syahyuniar; Adhiela Noer Syaief
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

Polytechnics as vocational education that applies more mastery of ability in the field of technology by prioritizing 70% practicum and 30% theory. As for workbench practicum, it is one of the basic practicum in the Automotive Engineering Department. This practicum contains basic mechanical work that is within the scope of conventional machining. The problem is the ineffectiveness in conducting the practicum process, where facilities and infrastructure are minimal and far away from the reach of work equipment, thus inhibiting the bench work practicum process. So it needs to be conducted on ergonomic workbench by determined good body position or movement based on the RULA value. The results of the application of ergonomic bench design workbench related that with setting equipment in one table, worker position, and the use of equipment had a value of RULA was 4.

Songket Industry Wastewater Processing Using Electrocoagulation Method Rusdianasari Rusdianasari; Ibnu Hajar; Indri Ariyanti
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 1 (2019): March
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

The increment of Songket popularity as the traditional fabric from South Sumatra increases the production of Songket and the wastewater produced during the dying process. The dying process produces the reddish wastewater, and if it is disposed of directly into the environment, it will have a negative impact on the waters. The wastewater treatment of this reddish liquid is by electrocoagulation method. Electrocoagulation method is contaminants removal by electrical and chemical treatment system. The electrocoagulation method in this research was conducted in a batch where the wastewater was treated using 16.5 x 7.0 x 0.2 cm aluminum electrode. The parameters varied were the current density and processing time to determine the pH value, color intensity, BOD5, COD, TSS, and phenol levels. The optimum condition obtained from this study at a current density of 25 A/m2 with a processing time of 160 minutes. The effectiveness of Songket wastewater electrocoagulation was 67.28% for TSS, 54.13% for BOD5, 63.64% for COD, color intensity 79.21% and phenol content of 74.93% respectively. The result has fulfilled the quality standard of textile industry wastewater treatment.

Page 1 of 1 | Total Record : 8

Filter by Year

2019 2019

Filter By Issues

All Issue Vol 21 No 2 (2021): July Vol 21 No 1 (2021): March Vol 20 No 3 (2020): November Vol 20 No 2 (2020): July Vol 20 No 1 (2020): March Vol 19 No 3 (2019): November Vol 19 No 2 (2019): July Vol 19 No 1 (2019): March Vol 18 No 3 (2018): November Vol 18 No 2 (2018): July Vol 18 No 1 (2018): March Vol 17 No 3 (2017): November Vol 17 No 2 (2017): July Vol 17 No 1 (2017): March Vol 16 No 3 (2016): November Vol 16 No 2 (2016): July Vol 16 No 1 (2016): March Vol 15 No 3 (2015): November Vol 15 No 2 (2015): July Vol 15 No 1 (2015): March Vol 14 No 3 (2014): November Vol 14 No 2 (2014): July Vol 14 No 1 (2014): March Vol 13 No 3 (2013): November Vol 13 No 2 (2013): July Vol 13 No 1 (2013): March More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kab. badung,

Bali

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kab. badung, Bali INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kab. badung,

Bali

INDONESIA