cover
Contact Name
Andi Syam Rizal
Contact Email
jft_fisika@uin-alauddin.ac.id
Phone
+6285242741788
Journal Mail Official
jft_fisika@uin-alauddin.ac.id
Editorial Address
Jurusan Fisika Gedung Fakultas Sains dan Teknologi Lt. 2
Location
Kab. gowa,
Sulawesi selatan
INDONESIA
Jurnal Fisika dan Terapannya
ISSN : 23021497     EISSN : 27152774     DOI : -
Core Subject : Science,
Jurnal Fisika dan Terapannya (JFT) adalah jurnal fisika yang diterbitkan oleh Jurusan Fisika, Fakultas Sains dan Teknologi, Universitas Islam Negeri Alauddin, Makassar. Jurnal ini diterbitkan dua kali setahun pada bulan Juni dan Desember. Jurnal ini mencakup artikel penelitian dalam semua aspek fisika dan terapannya. Jurnal ini pertama kali diterbitkan pada bulan Desember 2014 dan secara online di tahun 2019. Artikel hasil penelitian dalam jurnal ini berkaitan dengan fisika yang meliputi adalah fisika teori, fisika material, geofisika, fisika kesehatan, fisika instrumentasi, fisika komputasi, dan astrofisika.
Articles 189 Documents
DESAIN ALAT PENGUBAH ARUS TEGANGAN DC MENJADI ARUS TEGANGAN AC DENGAN MENGGUNAKAN TRANSISTOR 2N3055 Rahman, Rafiuddin; Lanto, Muhammad Said; Kadir, Ihsan
JFT : Jurnal Fisika dan Terapannya Vol 1 (2014): Desember
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v1i1.15744

Abstract

This research was conducted at the Department of Physics Laboratory instrumentation electronics, Faculty of Science and Technology, Alauddin State Islamic University (UIN) Makassar South Sulawesi. Formulation of research problems, namely (1) how to design transformers voltage DC voltage into AC current?, and (2) how much voltage and current is generated in transformers and DC voltage into AC?. In this study only uses transistor types (jengkol) with 2N3055 specifications. The results showed that (1) the design of transformers DC voltage into AC voltage current has been designed using 2N305 transistors to produce a form of inverters with 12 VDC input voltage and output voltage of 250 VAC. (2) The amount of voltage and current transformers resulting in a DC voltage into AC voltage currents generated before given input and output load currents.
PENGUJIAN KOEFISIEN ABSORBSI PADA PAPAN AKUSTIK MENGGUNAAN BAHAN DASAR BATANG JAGUNG DENGAN PEREKAT RESIN POLYESTER Ayu Hardianti Mahmud; Ihsan Ihsan; Sahara Sahara
JFT : Jurnal Fisika dan Terapannya Vol 7 No 2 (2020): DESEMBER
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v7i2.13830

Abstract

This study aims to determine the effect of thickness variations on the sound absorption coefficient of acoustic material from corn stalks. The study was conducted by making acoustic board samples from corn stems with Polyester Resin adhesive. In this study the thickness of the acoustic boards used were 0.7 cm, 1 cm, and 1.5 cm. The amount of frequency used is 250 Hz, 500 Hz, 1000 Hz, 2000 Hz. Based on the results of the research, the absorption coefficient value is proportional to the thickness, where the greater the thickness of a material, the lower the coefficient value produced. In the thickest sample with a thickness of 1.5 cm for a frequency of 250 Hz, the absorption coefficient value is 0.177, while at the frequency of 2000 Hz the absorption coefficient value is 0.084.
UJI KUAT TEKAN DAN KEAUSAN BAHAN KAMPAS REM DARI KOMPOSISI TEMPURUNG KEMIRI DAN SERAT BAMBU Athif, Muh Asyraf
JFT : Jurnal Fisika dan Terapannya Vol 5 No 1 (2018): Juni
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v5i1.15930

Abstract

This research aims to find out the best composition of brake lining materials from the shell of candlelnut and bamboo fiber through hardness testing and wear and tear of brake lining materials. The method used is direct emphasis using the Universal Testing Machine and Oghosi tools using the High Speed Universal Wear Testing Machine (Type OAT-U) Oghosi tool. Brake lining materials consist of shell powder of candlenut and bamboo fiber and then added aluminum powder and polyester resin with percent of specific composition for each sample. The results of this study were the five samples having lower wear value than the market but only the sample 4 with the composition of 15% of the shell powder of candlenut, 30% bamboo fiber, 15% aluminum powder and 40% polyester resin recommended as alternative material of brake lining because of its hardness close to the hardness of the material of brake lining of the market is 13.5 BHN and its wear is 2,96 x 10-6 mm2 / kg.Key Words: Strong Test of Pressure, Wear of Brush, Bamboo Fiber, Shell Powder of Candlenut, Aluminium Powder, and Resin
PENGARUH KEHALUSAN SEMEN TERHADAP KUAT TEKAN MORTAR Afni, Nur; Sahara, Sahara; Hernawati, Hernawati
JFT : Jurnal Fisika dan Terapannya Vol 2 (2015): Desember
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v2i0.16894

Abstract

This study aims to determine the effect of fineness to compressive strength of cement mortar. Mechanical parameters measured are fineness and compressive strength. From these test results, lead to the conclusion that the overall mechanical properties of the cement and mortar for all treatments meet the Indonesian National Standard (SNI) in 2004, the highest level of refinement that is 410.8 kg/m2, while the lowest is 387 kg/m2. For the compressive strength at age 3 days produces the highest value is 181 kg/m2, while the lowest is 143 kg/m2, at the age of 7 days resulted in the highest value is 242 kg/m2, while the lowest is 204 kg/m2, at the age of 28 days produces the highest value is 350 kg/m2, while the lowest is 265 kg/m2. Concluding that the more finely granular cement eat the higher the compress strength.
RANCANG BANGUN INSINERATOR DUA TAHAP (SOLUSI MENGATASI POLUSI UDARA PADA PEMBAKARAN SAMPAH) Hermansyah, Hermansyah; Said L., Muh.; Hernawati, Hernawati
JFT : Jurnal Fisika dan Terapannya Vol 4 No 1 (2017): Juni
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v4i1.15686

Abstract

This study aims to determine the model design and the incinerators tool mechanism to tackle air pollution in burning waste. The filter used is water by spraying using a spray nozzle on the tube filter. Testing is done by testing and observing the work incinerator combustion in incinerators and burning freely. Observations for plastic waste with a mass of 1 kg burned freely color black smoke, combustion rate 2 kg/hours, the combustion efficiency of 67.5 %. Combustion in incinerators two-stage color white smoke, combustion rate of 1.7 kg / h, the combustion efficiency of 67.5 %. At burning incinerator is better than burning freely. Keywords: Insinerator, asap, water spray, air
UJI KUAT TEKAN, DAYA SERAP AIR DAN DENSITAS MATERIAL BATU BATA DENGAN PENAMBAHAN AGREGAT LIMBAH BOTOL KACA Ardi, Andi Wahyuni; Iswadi, Iswadi; Said L, Muh
JFT : Jurnal Fisika dan Terapannya Vol 3 (2016): Desember
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v3i0.16834

Abstract

This experiment aims to know the influence of the increment of glass bottle waste to the pressure power, the water absorptive power and the density of the brick material and to know the comparison of the increment of glass bottle waste composition value to the brick material which produces the pressure power, absorptive power and the density match with standard value. This experiment uses tool test like beam with a size long 11 cm, wide 11 cm, height 5 cm with some various of the aggregate of glass bottle composition 0 %, 10 %, 20 %, 30 %, and 40 %. Making brick with the combination of soil, sand, water and the combination of aggregate of blass bottle waste, in the drying process within 1-2 days then burning in the  oven with temperature 900 oC for 3,5 hours. And then the brick is tested 3 parameters are the pressure, the absorptive and the density. Based on the test result it was gotten each of the parametre tests are the minimum value of the pressure is 223,41 kg/cm2 and the maximum is 253,37 kg/cm2 (based ont the class category 200 to 250 based on  SII-0021-1978); the water absorptive value was gotten in minimum is  9,38 %  and the  maximum is 19,05 % (based on  standard SII 15–2094–2000) and the dencity value is 1,48 - 1,64 gr/cm3 (based on  standard).
STUDI KARAKTERISASI DAERAH RAWAN LONGSOR DI DESA MALIWOWO KECAMATAN ANGKONA KABUPATEN LUWU TIMUR BERDASARKAN UJI X-RAY DIFFRACTION (XRD) Nurlaela, Nurlaela; Said L, Muh.; Iswadi, Iswadi
JFT : Jurnal Fisika dan Terapannya Vol 5 No 2 (2018): Desember
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v5i2.16108

Abstract

Research has been conducted in Maliwowo village, Angkona sub-district, East Luwu district, which aims to determine the mineral content and crystal structure of the soil in Maliwowo village, Angkona sub-district, East Luwu district. The method used in this study is the sampling technique carried out with five different points with a depth of 90 cm each. The results of X-Ray Diffraction (XRD) analysis showed that the minerals contained in sample A were 54,5% ,ite kaolinite 24,2% and 21,3% merrilite with successive crystal structures, namely monoclinic, triclinic and trigonal. The sample point B is illite 43,7%, albite 39,8% and merillite 16,5% with successive monoclinic, triclinic and trigonal crystal structures. The sample point C illite 47,9%, kaolinite 28,6% and feldspar 23,5% with crystal structures mononlinic, triclinc and monoclinic respectively. The point D sample was 53.7% ,ite albite 33.9% and 12.4% feldspar with monoclinic, triclinic and monoclinic crystal structures. The sample point E illite 54.4%, feldspar 27.7% and merrilite 17.9% with successive crystalline structures namely monoclinic, triclinic and trigonal.
ANALISIS DOSIS PAPARAN RADIASI DI UNIT RADIOLOGI RS. BHAYANGKARA MAKASSAR Hasmawati, Hasmawati; Sahara, Sahara; Hernawati, Hernawati
JFT : Jurnal Fisika dan Terapannya Vol 3 (2016): Desember
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v3i1.15722

Abstract

This study aims to measure the wall thickness of material radiation shield by using calipers, stage of measuring the radiation dose produced the best x-rays in different directions by using Surveymeter at the distance measuring point on the wall with a height of 10 cm, 1m, 2m, the third stage is measuring the radiation dose x-rays in the vertical and horizontal measurement with the object and without an object with a fixed voltage 75 Kv with distance measurements from a source to a device 1 meter and 2 meters in space and outside space. And the last stage takes raw radiation doses received by workers of the head of the installation space radiology Bhayangkara Makassar. Based on the research results in the first phase of the thick walls of the radiology that is 15 cm+2 mm (Pb) each side and wooden doors 5 cm+2 mm (Pb) and glass Pb 2 cm+2 mm (Pb), rate of radiation exposure resulting air x-ray in many directions obtained radiation is greatest there is in the direction of the left side air that is 3600 μSv/h, the dose rate on the measurement of vertical and horizontal with a specified distance of radiation of the total of the door operator vertical measurement that is equal to 3400 μSv/h, the dose received by the operator of the largest radiation received by the third receiver that is equal to 0.1599 μSv / h and the measurement results outside the room is 0.00 μSv / h was not detected while the radiation received by the receiver the first small at 0.1546 μSv/h and the mean dose average received by the operator of 0.1 μSv/h this is in accordance with the SNI allowed for workers is 50 mSv/ h in the first year. Keywords : radiation dose , radiation workers , radiation shield
POLA SESAR SADDANG BERDASARKAN TINGKAT SEISMISITAS DAN FOKAL MEKANISME (Studi Kasus Januari 2010 - Juli 2020) Risnawati Risnawati; Ihsan Ihsan; Ayusari Wahyuni; Muh. Said L.
JFT : Jurnal Fisika dan Terapannya Vol 8 No 1 (2021): JUNI
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v8i1.19277

Abstract

The research of the Saddang fault pattern based on the level of seismicity and focal mechanism (a case study in January 2010- July 2020) aims to determine the level of seismicity in the Saddang fault area and the Saddang fault focal mechanism in the 2010-2020 earthquake. The data which were used were secondary data from the BMKG catalog from January 2010 - July 2020. The coordinating limit is 118.50 ° East Longitude 120.60 ° East Longitude and (-2.60 ° South Latitude) - (-5.70 ° South Latitude) there were 1425 earthquakes. This research used ArcGis application to measure seismicity distribution map and seiscomp3 to measure focal mechanism. Furthermore, the focal mechanism divides the region into three regions. The results which obtained from the seismicity map obtained a high level of seismicity with a shallow depth. Which was caused by the lack of factors from the active Saddang fault and Sulawesi who had four plate junctions. The results of the focal mechanism in each region had the whole type of shear fault or horizontal. Keywords: Earthquake, geology software ArcGis, software seisco
RENEWABLE ENERGY: PHOTOVOLTAICS, AN INTRODUCTION Iswadi, Iswadi
JFT : Jurnal Fisika dan Terapannya Vol 1 (2014): Desember
Publisher : Universitas Islam Negeri Alauddin Makassar

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24252/jft.v1i1.15754

Abstract

Energy is one of the most hot issue today.  Energy consumption has increasing every year around the world but the sources  not increasing significanly.  Most of the energy source come from coal and oil with decrease every year. However oil and charcoal tends to be distinctive near future since it not renewable. Besides, it is polluting, environmentally harmful and rather expensive. As consequence  it is important to explore another renewable energy resources. One good example is solar energy, with using sel phovoltaics technology. Photovoltaics technology have been presented with higher efficiency and low cost in production such as perovskite solar cell.

Page 6 of 19 | Total Record : 189