cover
Contact Name
Nyoman Pasek Nugraha
Contact Email
paseknugraha@gmail.com
Phone
+6281999131789
Journal Mail Official
paseknugraha@gmail.com
Editorial Address
Jl. Udayana, Kampus Tengah, Singaraja-Bali
Location
Kota denpasar,
Bali
INDONESIA
Jurnal Pendidikan Teknik Mesin Undiksha
ISSN : 26141876     EISSN : 26141884     DOI : http://dx.doi.org/10.23887/jjtm.v7i1.18616
Jurnal Pendidikan Teknik Mesin, adalah jurnal ilmiah yang diterbitkan oleh Jurusan Pendidikan Teknik Mesin, Fakultas Teknik dan Kejuruan, Universitas Pendidikan Ganesha. Jurnal ini bertujuan untuk mewadahi artikel-artikel hasil penelitian dan hasil pengabdian masyarakat dibidang pendidikan dan pembelajaran teknik. Pada akhirnya Jurnal ini dapat memberikan deskripsi tentang perkembangan ilmu pengetahuan dan teknologi di bidang pendidikan teknik mesin bagi masyarakat akademik. Jurnal ini terbit 3 kali setahun.
Arjuna Subject : Umum - Umum
Articles 343 Documents
Perbandingan Kecepatan Angkat Dongkrak Botol Menggunakan Variasi Viskositas Fluida Hidrolik: Comparison of Bottle Jack Lifting Speed Using Hydraulic Fluid Viscosity Variations Putra Ragil Hidayatulloh; Wirawan Sumbodo
Jurnal Pendidikan Teknik Mesin Undiksha Vol. 15 No. 1 (2027)
Publisher : Universitas Pendidikan Ganesha

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23887/jptm.v15i1.120153

Abstract

Viscosity is an important physical property of hydraulic fluids that affects their ability to transmit pressure, provide lubrication, act as an internal insulator, and determine the efficiency and performance of the hydraulic system. This study aims to evaluate the impact of changes in hydraulic fluid viscosity on the load-transfer speed of a two-ton manual bottle jack under conditions where no additional load is applied. This study was conducted using a purely experimental laboratory method, with a quantitative approach based on comparison. The fluids used consisted of Pertamina Turalik with viscosities of ISO VG 32, ISO VG 46, and ISO VG 68. All tests were carried out with a pumping rhythm maintained consistently with a metronome for 11 seconds, and each variation was tested 3 times. The results showed that increasing fluid viscosity increased piston lifting speed. ISO VG 68 fluid provided the highest average lifting speed of 3.86 mm per second, followed by ISO VG 46 fluid with an average speed of 3.68 mm per second, and ISO VG 32 fluid achieved an average speed of 3.62 mm per second. These findings indicate that in manual bottle jack systems that have low flow rates, fluids with higher viscosity can improve internal sealing capabilities, thereby reducing fluid leakage, increasing pump volumetric efficiency, and accelerating the cylinder chamber filling process. Therefore, the use of ISO VG 68 hydraulic fluid provides optimal piston lifting results under no-load test conditions. This optimization also supports SDG 9 targets regarding technological efficiency and infrastructure innovation.
t Karakteristik Dimensi Hasil Pengecatan Kain Menggunakan Mesin CNC Airbrush: Pengaruh Diameter Nozzle, Tekanan Udara, dan Jarak Nozzle I Nyoman Dwiky Dartawan Putra Nugraha; I Gusti Ngurah Nitya Santhiarsa; I Made Gatot Karohika
Jurnal Pendidikan Teknik Mesin Undiksha Vol. 15 No. 1 (2027)
Publisher : Universitas Pendidikan Ganesha

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23887/jptm.v15i1.120387

Abstract

The movement of a CNC airbrush machine can be programmed with high precision however, the dimensional accuracy of the resulting pattern is still influenced by several factors. This study examined the effects of nozzle diameter, air pressure, and nozzle distance on fabric painting results and identified the parameter combination with the lowest dimensional error. A full factorial experiment with three factors at three levels was used. The tested nozzle diameters were 0.2, 0.3, and 0.5 mm; air pressures were 20, 25, and 30 psi; and nozzle distances were 0.5, 1.0, and 1.5 cm. Each combination was repeated three times, producing 81 observations. A 30 mm × 30 mm square was painted on prima cotton fabric. Pattern length, width, and line width were measured from calibrated images using ImageJ and analysed using three-way factorial analysis of variance. Mean pattern length and width weres 30.686 mm and 30.519 mm, while mean line width and dimensional error were 2.201 mm and 0.767 mm. All three factors had significant effects. Nozzle distance had the strongest effect on line width, whereas nozzle diameter was the dominant factor for dimensional error. The combination of a 0.2 mm nozzle, 25 psi pressure, and 0.5 cm distance produced the lowest error of 0.073 mm, equivalent to 99.76% accuracy. These results provide an initial operating reference for precise contours and small fabric patterns. Keywords: air pressure; CNC airbrush; factorial ANOVA; nozzle diameter; nozzle distance
The Efektivitas Simulator CNC Android Growth Mindset Terhadap Hasil Belajar Kognitif Siswa SMK : Effectiveness of Android CNC Simulator Using a Growth Mindset Approach on Student Learning Outcomes in Vocational Schools Naufal Ega Firjatullah; Marsono; Kusminartin; Muh. Taufik Efendi
Jurnal Pendidikan Teknik Mesin Undiksha Vol. 15 No. 1 (2027)
Publisher : Universitas Pendidikan Ganesha

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23887/jptm.v15i1.121455

Abstract

Limited access to CNC machines for hands-on practice is a common obstacle that hampers students' mastery of NC/CNC Machining Techniques in vocational high schools. This study examines whether an Android-based instructional tool, the CNC Simulator, can help overcome this constraint and strengthen students' cognitive learning outcomes. A quantitative Quasi-Experimental design was applied, comparing pre-test and post-test scores of a treatment group against a comparison group. Data were collected from Grade XI students at a state vocational school in Malang Regency, selected through purposive sampling and divided into an experimental group and a control group, each comprising 18 students. An independent-samples t-test produced a t-value of 3.29, exceeding the critical t-value of 2.032 at a 0.05 significance level with 34 degrees of freedom, indicating a significant difference between groups. The normalized gain (N-Gain) for the experimental group reached 0.528, well above the 0.30 threshold used to classify a treatment as effective. Together, these results confirm that the CNC Simulator outperforms conventional instruction in raising students' learning outcomes. Based on these findings, productive-subject teachers are encouraged to adopt the CNC Simulator as a supplementary medium when machine facilities are scarce, while also nurturing a growth mindset among learners. Future studies are recommended to pair this simulator with other innovative instructional models and to assess its influence beyond the cognitive domain, extending into students' psychomotor competencies.