cover
Contact Name
Dina Mariani
Contact Email
dinamariani@unimus.ac.id
Phone
+6285299398663
Journal Mail Official
mediaelektrika@unimus.ac.id
Editorial Address
Universitas Muhammadiyah Semarang FT-FMIPA Building, 7nd Floor. Department of Electrical Engineering Jl. Kedungmundu Raya No. 18, Kota Semarang, Prov. Jawa Tengah, Indonesia 50273 Phone: 085299398663 Email: mediaelektrika@unimus.ac.id
Location
Kota semarang,
Jawa tengah
INDONESIA
MEDIA ELEKTRIKA
ISSN : 19797451     EISSN : 2579972X     DOI : 10.26714/me.14.2.2021.62-75
Media Elektrika is an electrical engineering journal that gives concerns on sciences related to electrical engineering. It includes the following fields: Electrical power engineering Electronics Telecommunication Control Informatics and computer technology
Articles 207 Documents
EFEKTIFITAS PEMANFAATAN PASIR PANTAI KUKUP DAN SILANE SEBAGAI FILLER BAHAN ISOLASI RESIN EPOKSI UNTUK ISOLATOR LISTRIK Moh Toni Prasetyo; Aris Kiswanto
MEDIA ELEKTRIKA Vol 8, No 1 (2015): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (316.386 KB) | DOI: 10.26714/me.8.1.2015.%p

Abstract

Insulation materials that commonly used in air insulation, which, is operated at high voltage, are the porcelain, glass, and polymer materials. One of the insulating polymer materials that are used is epoxy resin because it has several advantages compared to that. However, this insulation material has a degradation of the surface due to environmental and cause insulation coated with dirt and chemicals in the long time. Material that was used in this research was epoxy resin polymer isolation using of comparison values (base material diglycidyl ether of bisphenol-A: hardener material metaphenylene diamine) were 1:1, with the increase of silane and high calcium coastal sand as filler by the value of 10%, 20%, 30%, 40%, and 50%.Research was done in laboratory according to standard IEC 587: 1984. In this study, the effect of variation in stoichiometry to the hydrophobic contact angle value, leakage current waveforms, and surface degradation caused by erosion and tracking processes and tracking time were analyzed.From the results of the research, it was obtained that the epoxy resin that was used in this research are categorized as hydrofobik and partially wetted. The increase concentration of silane dan Kukup coastal sand as filler caused the increase in contact angle which meant the increase in surface insulation resistance, so that leakage currents flew on the surface not easily and slow down the aging or the degradation decreasing on the surface of insulating material. Concentration value of filler that had the optimal performance of the tracking process and erosion was 40%.Keywords : angle of contact, epoxy resin, hidropobik, isolator, leaky current, materials filler
PENGOLAHAN CITRA PADA SINYAL EKG Jaenal Arifin; Norma Amalia
MEDIA ELEKTRIKA Vol 11, No 1 (2018): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (874.58 KB) | DOI: 10.26714/me.11.1.2018.%p

Abstract

Elektrokardiografi merupakan perangkat alat yang dapat merekam aktivitas sinyal jantung manusia. Hasil keluaran aktivitas sinyal jantung ditunjukan pada lembar kertas ekg. Pengolahan citra sinyal jantung manusia dapat dilakukan dengan lembar kertas ekg.Penelitian ini mengolah sinyal ekg dari hasil pengukuran yang telah dilakukan. Pada penelitian ini mengolah citra pada sinyal ekg.   Pengolahan citra pada sinyal ekg ini meliputi beberapa tahap. Tahap awal adalah melakukan pengukuran oleh subjek atau relawan, tahap selanjutnya mengambil citra sinyal ekg, tahap scanning, tahap pengubahan citra true color ke grayscale, tahap median filter, tahap penentuan nilai ambang dan tahap morphology citra pada sinyal ekg. Hasil penelitian menunjukkan bahwa citra sinyal ekg yang telah diolah tetap mempertahankan fitur sinyal ekg dan mempunyai informasi yang jelas (tidak distorsi atau cacat) pada gelombang sinyal ekg tersebut. Selanjutnya citra sinyal ekg tersebut dapatdiolah untuk tujuan tertentu. Bisa untuk tujuan penelitian atau tujuan analisa pola citra sinyal ekg. Keywords:Elektrokardiografi,Sinyal ekg, Citra Sinyal ekg.
Potensi Clean Development Mechanism pada Pembangkit Mikrohidro 120 KW - Gunawan; Didiek Eko Budi Santoso; M. Subchan
MEDIA ELEKTRIKA Vol 3, No 2 (2010): Electrical Engineering
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1389.873 KB) | DOI: 10.26714/me.3.2.2010.%p

Abstract

Polential of Micro Hydro Power in remote areas is the most realistic as the primary energy for electricity generation. Potential energy become a growing alternative for the region to diversify its electricity supply. The issue of global warming that encourages the use of renewable energy in an effort to prevent damage to the natural speed of following up a global agreement under the Kyoto Protocal. One program in the reduction of exhaust emissions is the Clean Development Mechanism (CDM). Through this concept all the activities of energy usage can be measured and calculated potential relation with the exhaust emissions.CDM potential measurement begins by defining the instrument to be used. MHP is the power output is a fixed value that is used as a reference that will measure the impact if generated by fossil energy utilization. This step is an approach that shows how the potential for greenhouse gas emissions that can be prevented if the electrical power needs supplied by renewable energy-based generation.The sample of study is MHP Cinta Mekar in Subang district indicates that this location was proposed as a viable small-scale projects under the CDM. MHP is able to produce electrical energy of 120 KW. CDm potential is calculated are the reduction of fossil energy consumption of 1.5 tons per day. In addition to equality of use of fossil fuels for electrical potential energy also has the potential to reduce environmental pollution by 1474.2 tons / year of CO2.Keyword : CDM, MHP, Energy, Pollution
ANALISA KONTRUKSI JARINGAN TEGANGAN MENENGAH 20 KV TANPA KAWAT TANAH TERHADAP SAMBARAN INDUKSI PETIR Studi Kasus Di PT PLN ( Persero ) Area Semarang Rayon Boja Feeder BSB 4 GI BSB Muhammad Nur Arif; Bambang Supradono; Agung Budi Santoso
MEDIA ELEKTRIKA Vol 5, No 2 (2012): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (163.563 KB) | DOI: 10.26714/me.5.2.2012.%p

Abstract

A bolt of lightning strikes the induction is on the ground near a transmission line resulting in a phenomenon that caused of trensient electromagnetic fields from the lightning channel. This phenomenon is happening at lightning conductor wire. This event raised over voltage and resulting wave propagating on both sides of the wire in the strike lasts. In calculating the induction stroke used Shielded Factor (FP) is defined as the quotient ofthe induced voltage and induced voltage ground wire without a ground wire. If there is no ground wire, the neutral wire effect on induced voltage on the wire the same phase as the influence of the ground wire to the voltage induced in the phase wire. Since the neutral high wire above the ground is lower than the high-wire phase, greater than shielded factor of the channel with the ground wire. There are times when the neutral wire was installed over the wire so that the phase factor will be smaller shielded. Construction is crucial lightning disturbances. From this analysis concluded that the results obtained from data disruption due to lightning feeder PMT 4 GI BSB obtained 3 times a distraction while the calculation results showed interference by 4 times with 24.4 km length of the network there is no significant difference. Any differences due to changes in network construction are not communicated as elevation neutral wire that will affect shielded factor.
ANALISA PENGARUH KUALITAS BATUBARA TERHADAP BIAYA PEMBANGKITAN (STUDI KASUS DI PLTU REMBANG) Agus Adhi Nugroho
MEDIA ELEKTRIKA Vol 7, No 1 (2014): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (268.193 KB) | DOI: 10.26714/me.7.1.2014.%p

Abstract

Coalisone of the sourcesof energythat are widely usedinpower generation. Indonesiancoal productionas much as254milliontons in 2009as much as75% is exported, while the remaining25% for domestic consumption. Since much ofhigh-gradecoal(coal highrange) wereexportedout of the countrymakes theplantsin Indonesiawereoperating usingwith alow qualitycoal. The results ofthe analysis carried outinPLTU RembangofSeptember-November 2013can be concludedthatthe lower thecalorific valueof coalisusedthe higher themass flow rateof coal, thesteammass flow rateisrelativelythe same. The higherthe load, the coalmass flow rateis also higher,the specificfuelconsumption(kg /kWh) was decrease,theheatratewas decrease. However,the thermalefficiencywas increase. When theload of180MWto 250MWmoreefficientuseof coalcomposition100% LRC. Ata loadof 200MWto 250MWmoreefficientuseof coalcomposition of25%MRCand75% LRC. From theaverage value ofthe price ofproduction, moreefficientuseof coalcomposition100% LRC, butwiththecompositioncan notachievethe highestload. When viewedfrom theaverage valuethatcanmeet thehighestload, themore efficientisbyusing thecoalcomposition of50% MRC and50% LRC. Keywords: PLTU Rembang, Heatrate, ThermalEfficiency.
ANALISA JARINGAN FTTH STO JOHAR KE MG SETOS BERDASARKAN TEKNOLOGI GPON DI PT. TELKOM AKSES DIGITAL LIFE REGIONAL IV JATENG DAN D.I.Y Mochamad Subchan Mauludin; Indah Rahmawati
MEDIA ELEKTRIKA Vol 10, No 1 (2017): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (477.904 KB) | DOI: 10.26714/me.10.1.2017.%p

Abstract

Serat optik merupakan media transmisi yang dapat menyalurkan informasi dengan kapasitas besar dan teknologinya disebut Jaringan Lokal Akses Fiber. FTTH (Fiber To The Home). Analisa jaringan FFTH berteknologi GPON dengan parameter daya transmisi di OpticalLine Terminal, daya receiver, redaman kabel serat optik, konektor, passive splitter, dan sambungan, jaringan FTTH  STO Johar ke MG Setos dilakukan dengan metode link power budget dan rise time budget. Pr sensitivitas uplink dan downlink  menunjukkan nilai rata-rata, yakni  13,71997dBm dan -13,55897 dBm sehingga margin daya yang didapatkan adalah 0,28003  dBm untuk uplink dan 0,44103  dBm untuk downlink. Sedangkan untuk rise time total sebesar 0,667 ns untuk  downlink. Hasil dari perhitungan dan skema FTTH STO Johar ke MG Setos sesuai denganstandar di PT. Telkom.Kata Kunci: FTTH, GPON, link power budget, rise time budget
KORELASI ANTARA MEDAN MAGNET DENGAN TINGKAT DISTORSI HARMONISA PADA MOTOR INDUKSI TIGA FASA Luqman Assaffat
MEDIA ELEKTRIKA Vol 2, No 2 (2009): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (725.323 KB) | DOI: 10.26714/me.2.2.2009.%p

Abstract

Motor induksi tiga fasa mempunyai rangkaian ekivalent yang sama dengan sebuah transformator, dimana keduanya mempunyai prinsip kerja yang sama yaitu dengan cara induksi magnet yang menghasilkansebuah tegangan. Sebagaimana halnya transformator, motor induksi tiga fasa digolongkan sebagai jenisbeban yang tak linier karena mempunyai sifat kejenuhan magnetisasi sebagai akibat dari penggunaan tipematerial magnetnya.Beban – beban yang tak linier akan menghasilkan suatu polutan daya listrik yang sering disebutdengan harmonisa. Harmonisa diukur dengan suatu tingkatan yang disebut Total Harmonics Distortion,THD, atau dalam istilah Bahasa Indonesia sering diartikan sebagai Tingkat Distorsi Harmonisa. Dari haltersebut dapat diduga bahwa harmonisa yang dihasilkan oleh motor induksi tiga fasa disebabkan olehbesarnya medan magnet yang terjadi. Sehingga perlu dilakukan suatu uji korelasi antara besarnya medanmagnet dengan tingkat distorsi harmonisa pada motor induksi tiga fasa.Hasil pengujian menunjukkan korelasi menunjukkan bahwa Tingkat Distorsi Harmonisa pada motorinduksi tiga fasa, baik THD teganan maupun THD arus, dipengaruhi oleh besarnya medan magnet yangterjadi.
PENGARUH JATUH TEGANGAN TERHADAP KERJA MOTOR INDUKSI TIGA FASA MENGGUNAKAN SIMULINK MATLAB Partaonan Harahap
MEDIA ELEKTRIKA Vol 9, No 2 (2016): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (572.642 KB) | DOI: 10.26714/me.9.2.2016.%p

Abstract

Pengaruh jatuh tegangan jala-jala dengan beban bervariasi terhadap daya input, arus input, kecepatan putar rotor, slip, daya output, rugi-rugi dan efisiensi motor induksi tiga fasa.Diperoleh dari simulasi jatuh tegangan sebesar 0%, 2%, 4%, 6%, 8% pada beban 4 N-m yang mengalami kenaikan adalah arus input dari 6,23-6,77 ampere, juga slip dari 3,273,33 %, dan yang mengalami penurunan adalah kecepatan putar rotor dari 1450,92-1450,01 rpm, daya output dari 4912,55-4263,93 watt dan effisiensi dari 88,99-87,53 %. Pada beban 5 N-m yang mengalami kenaikan adalah arus input dari 6,35-6,94 ampere, slip dari 3,36-3,43 %, dan yang mengalami penurunan adalah kecepatan putar rotor dari 1449,67-1448,52 rpm, daya output dari 4933,074329,55 watt dan effisiensi dari 89,04-87,71 %. Pada beban 6 N-m yang mengalami kenaikan adalah arus input dari 6,48-7,03 amper, slip dari 3,44-3,53 %, dan yang mengalami penurunan adalah kecepatan putar rotor dari 1448,46-1447,03 rpm, daya output dari 4964,58-4365,17 wattdan effisiensi dari 89,11-87,81 %.Kata Kunci: Jatuh tegangan jala-jala, Motor induksi tiga fasa rotor sangkar
DESAIN SISTEM INFORMASI PENGGAJIAN KARYAWAN BERBASIS WEB Mochamad Subchan Mauludin; Ana Durul Firdaus
MEDIA ELEKTRIKA Vol 12, No 1 (2019): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (545.754 KB) | DOI: 10.26714/me.12.1.2019.43-49

Abstract

Kinerja di sebuah instansi di pengaruhi oleh sistem penggajian dimana sistem ini menyajikan cara-cara penggajian pegawai secara tepat dan akurat. Sistem Informasi Penggajian memegang peranan yang sangant penting dalam hal keuangan dalam sebuah instansi karena sangat mempengaruhi kinerja karyawan dalam kesehariannya. Pembuatan sistem informasi penggajian ini menggunakan metode System Development Life Cycle, dengan menggunakan tiga tahapan yaitu tahap perencanaan, analisa dan desain, pengumpulan data menggunakan metode observasi dan wawancara. Sistem Penggajian terbukti mempermudah dan mempercepat proses pengolahan data penggajian, serta meminimalisir kesalahan.
REKONSTRUKSI “COLD END YOKE” SEBAGAI ALAT PENGGANTIAN ISOLATOR LINK PENDEK SUTET 500 kV Achmad Solichan; - Subronto
MEDIA ELEKTRIKA Vol 2, No 1 (2009): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (242.278 KB) | DOI: 10.26714/me.2.1.2009.%p

Abstract

Metode PDKB dalam pemeliharaan SUTET 500 kV memegang peranan yang sangat penting untuk menjaga keandalan dan kontinuitas sistem penyaluran sistem tenaga listrik. Metode PDKB mengalami kendala dalam pemeliharaan isolator link pendek karena peralatan Cold End Yoke keluaran manufactur tidak sesuai konstruksinya untuk kontruksi tower tension dengan aksesoris isolator link pendek. Untuk itu sangat perlu dilakukan rekonstruksi Cold End Yoke yang ada agar dapat difungsikan pada konstruksi tersebut. Hasil penelitian menunjukkan Cold End Yoke rekonstruksi dapat dipakai dan kuat menahan tegangan tarik sesuai kebutuhan SUTET 500 kV.

Page 7 of 21 | Total Record : 207