Garuda - Garba Rujukan Digital

All

Jurnal Optimasi Sistem Industri

JOSI
Website

Published by Universitas Andalas

ISSN : 20884842 EISSN : 24428795 DOI : -

Control & Systems Engineering Decision Sciences, Operations Research & Management Engineering Industrial & Manufacturing Engineering Mechanical Engineering

Jurnal Optimasi Sistem Industri (JOSI) is a peer-reviewed journal that is published periodically (April and October) by the Department of Industrial Engineering, Faculty of Engineering, Universitas Andalas, Padang.

Arjuna Subject : -

Articles 394 Documents

5 6 7 8 9

Perancangan Sistem Informasi Manajemen Rantai Pasok Minyak Sawit Mentah Berbasis GIS Ringgo Afrinando
Jurnal Optimasi Sistem Industri Vol. 11 No. 2 (2012): Published in 1st October 2012
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

This study discusses about information systems of CPO supply chain management in PTPN 6 Ophir. PTPN 6 management still use the conventional system (archival documents) in running their business. This information is not yet integrated with the map of plantation, so it will allow errors and inaccuracies in the planning, management and maintenance of oil palm plantations. Otherwise, the output from the production and processing of FFB to CPO and Palm Kernel also has not been well managed. So this would have difficulties in data storage on the the plantation and harvest information and to make decision for the FFB receiving division and distribution of CPO and Palm Kernel. Therefore needed a system that can control the activities in the oil palm plantation and processing by utilizing information technology system that integrates mapping and data information in a software that will facilitate decision making for planning and maintenance.The stages of the study consist of preliminary study, the selection method of problem solving, designing model system, database and software design and verification and validation of the model system. The study used primary data and secondary data. The primary data includes interviews about the company's business processes and the mechanisms of oil production. Secondary data includes administrative forms such as SPB, form the collection of FFB, weight measurement form and daily report sheet of factory. Model systems in the information system design used Object Oriented Analysis and Design method. This method will considers and designing systems with focusing the objects associated with the system. Verification results of the design has been done by using the method of Computerized Model Verification. This method to see whether the information system has been designed to run properly with the conceptual model of the system. Validation has been done by using Operational Validity. Validity Operational techniques used Black Box Test Method or directly test by the person that understand the issues in study.The results was Information System Software Design of CPO Supply Chain Management at PTPN 6 already integrates all data and information on the plantation, processing and marketing of CPO and palm kernel oil in a web-based application with support for spatial data processing in online mapping format. The system model can be seen through the business process diagram, use case diagram, class diagram and entity relationship diagram.Keywords: Information System,Supply Chain Management, Crude Palm Oil, GIS

Pengembangan Algoritma Manajemen Risiko Proyek Konstruksi Yetrina, Mutiara
Jurnal Optimasi Sistem Industri Vol. 17 No. 1 (2018): Published in April 2018
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

The success of a project is uncertain. There is a possibility that the project was successful or failed. Some of the risks that may occur in the project include the arrival of goods or the completion of work late from the time set, design changes due to obstacles in the field, as well as other risks. It is therefore necessary to study the project risks to identify potential problems that may occur and make decisions to reduce risks and increase the likelihood of success of the project. In order for risk management to be performed, the owner must know the steps in evaluating the project and the steps in the implementation of risk management. This study discusses the development of algorithms for project evaluation and risk management. The resulting algorithm is then implemented to the CC-II civil construction project at Indarung VI Project. The results of the implementation show that the project is not running in accordance with the plan. The dominant factors causing delays include BOQ miscalculation by consultants, inadequate and slow decision-making mechanisms, and details of workmanship changes.

Pengembangan Kualitas Pelayanan Produk Telekomunikasi Selular Diatas Kapal Menggunakan Metode Service Quality & Quality Function Deployment Maya Arlini Puspasari; Nia Kurniasih
Jurnal Optimasi Sistem Industri Vol. 12 No. 1 (2013): Published in 1st April 2013
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

The need for telecommunications, including the category of primary need for the people of Indonesia, one of the important aspects that need to be considered by the telecommunications company is a technological innovation that can cover all of Indonesia to outlying places, not only telecommunications on land even when in the middle of the ocean though. With Cellular Telecommunications Company cooperation to support the availability of telemetry, then develop into the greatest benefit is the availability of the Mobile phone network for the passengers on board, to continue to innovate and deliver the best to customers, the service providers must continue to improve quality. Research conducted using the SERVQUAL method to measure the quality of service based on the five dimensions of service quality by analyzing gaps that occurs due to a mismatch between customer expectations and perceptions of the quality of service received. In this study wants and expectations of consumers translated into House of Quality in Quality Function Deployment. Results of research propose using strategy value to get priority repairs according to the company's abilityKeywords: Product Telecommunication, SERVQUAL, Quality Function Deployment, Quality Improvement

Analisis Penerapan Lean Production Process untuk Mengurangi Lead Time Process Perawatan Engine (Studi Kasus PT.GMF AEROASIA) Wahyu Adrianto; Muhammad Kholil
Jurnal Optimasi Sistem Industri Vol. 14 No. 2 (2015): Published in 1st October 2015
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

Engine maintenance strives to always improve its service excellence with tools such as gate system where the system is expected to realize the lead time for 60days. In the implementation of the gate system is still not able to meet the expected target. During maintenance or overhaul the engine is still encountered waste or waste that causes the target cannot be met. Lean Manufacturing is an approach that aims to minimize waste that occurs in the process flow.Understanding the conditions of the process described in Value Stream Mapping for further elaborate activities that have the value-added and non-value added.Through seven waste concept, then be weighted to determine the most dominant type of waste.From the data processing is obtained that through the Value Stream Mapping is known gate 1 and gate 3 is the point that there are many wastes. Weighting and ranking of seven existing waste in the process of the activity obtained results in the form of a waste critical sequence of seven existing waste. Highest weights on the type of waste waiting with a weight of 0.38. Results of Root Cause Analysis in mind that the root cause of waste waiting for that data is maintained, the lack of attention to people development, There are still bugs in the system and miscommunication.

Inventory Control Model of Beef for Rendang Products Feby Gusti Dendra; Elita Amrina; Ahmad Syafruddin Indrapriyatna
Jurnal Optimasi Sistem Industri Vol. 22 No. 1 (2023): Published in May 2023
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

The definition and function of inventory management reveal the importance of modern industry in formulating policies that regulate the supply of raw materials, semi-finished products, and finished products. Unfortunately, most companies fail to consider the characteristics of their raw materials when determining inventory strategies. Raw materials that are perishable are those that consider their service life and storage time. Inventory management plays a crucial role in supply chain management, especially for perishable raw materials, such as food products. PT X, a food business in Padang, experienced difficulty in meeting the demand for rendang products due to a lack of raw materials. Therefore, this study aims to develop an inventory management model that takes into account the perishable raw materials' expiration time. The model development consists of three stages: model development design, inventory model formulation, and model testing. The proposed model resulted in a storage time interval of five days and an optimal order quantity of 34 kg of meat with a safety stock of 14 kg. Implementing this model led to lower total inventory costs for PT X than the actual conditions of the company. The total inventory cost obtained using this model is Rp279,797,822. This study emphasizes the importance of considering the characteristics of raw materials in determining inventory strategies to optimize inventory management effectively and efficiently. The study's findings can serve as a reference for other food businesses encountering similar inventory management challenges in the perishable food industry.

SEM Analysis of Contractor Performance in Accelerating Electrical Construction Project: Insights from Herzberg's Dual Factor Theory Virda Hersy Lutviana Saputri; Nasrulloh
Jurnal Optimasi Sistem Industri Vol. 23 No. 1 (2024): Published in July 2024
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

In the rapidly developing electrical construction industry, the success of organizations is directly linked to the performance of their business partners. This study focuses on Indonesia's state-owned electrical enterprises, where a notable decline in Key Performance Indicators (KPIs) has raised concerns, hypothesizing that deficiencies in contractor performance are a major barrier to the timely completion of electrical construction projects. At the core of this issue is the role of human resources, identified as a pivotal factor in contractor performance that directly impacts project completion. The aim of the research is to elucidate the complex dynamics between motivator and hygiene factors, which are fundamental to Herzberg's dual factor theory, and their impact on the performance of the contractor's employees. Using Structural Equation Modeling (SEM), the study analyzes data from questionnaires distributed to 250 industry professionals. The analysis provides key insights into how these factors significantly influence job satisfaction and, ultimately, employee performance. These insights play a critical role in strategically planning contractor management practices. By emphasizing the need to understand the key factors driving employee satisfaction and performance, the study lays a solid foundation for designing effective employment contracts and management strategies. The practical implications of this research are significant, offering a pathway for contractors to enhance employee satisfaction and performance. This ultimately leads to the delivery of high-quality electrical infrastructure projects efficiently and promptly, underlining the study's relevance and importance in the contemporary industrial landscape.

Optimizing Surface Finish and Dimensional Accuracy in 3D Printed Free-Form Objects Farid Wajdi; Mohd Sazli Saad
Jurnal Optimasi Sistem Industri Vol. 22 No. 2 (2023): Published in December 2023
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

3D printing of free-form objects presents inherent complexity due to their organic and intricate shapes. Designers engage with such objects, considering a range of factors including aesthetics, engineering viability, and ergonomic comfort. This research is focused on achieving the most effective printing parameters for a free-form object utilizing the Digital Light Processing (DLP) technique within a 3D printer. Within this study, a squeezed hexagonal tube-shaped CAD model was employed as an experimental subject, following the principles of the Response Surface Method (RSM). The research delved into the optimization of printing parameters, particularly layer thickness and exposure time, to enhance the dimensional accuracy and surface quality of the free-form model. Two levels were established for each factor: layer thickness was set at 0.06 mm (low) and 0.08 mm (high), while exposure time was tested at 6 s (low) and 8 s (high). The assessment of surface quality involved a qualitative evaluation employing a digital microscope to identify potential defects and imperfections in the print outcomes. The investigation culminated in the identification of the optimal printing parameters: a layer thickness of 0.0753 mm and an exposure time of 7.2143 seconds. This achievement not only enhances the understanding of 3D printing variables in the context of intricate free-form models but also contributes to the broader field of additive manufacturing parameter optimization.

Konsep Persediaan Minimum Maksimum Pengendalian Part Alat Berat Tambang PT Semen Padang Dio Putera Hasian
Jurnal Optimasi Sistem Industri Vol. 11 No. 1 (2012): Published in 1st April 2012
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

Bureau of mining heavy equipment maintenance at PT. Semen Padang have task in maintenance mine heavy equipment with preventive maintenance although breakdown maintenance. Part inventory is needed to make this activity work properly. If stockout happened will have the impact to PT.Semen Padang mining and production activity. To solve this problem, minimum-maximum inventory control policy is used to give an optimum value of inventory mine heavy equipment. This research is focused in filter and lubricant inventory because they have high demand rate. Data consumption filter and lubricant from January until December 2010 is used in this research. The service level that used is 95%. The result is quantity optimum inventory mine heavy equipment at filter and lubricant with application part inventory of mine heavy equipment. Because it can keep stockout although excess inventory.Keywords: stockout, optimum, inventory

Integrasi Quality Function Deployment (QFD) dan Conjoint Analysis untuk Mengetahui Preferensi Konsumen Desrina Yusi Irawati; Moses Laksono Singgih; Bambang Syarudin
Jurnal Optimasi Sistem Industri Vol. 13 No. 2 (2014): Published in 1st October 2014
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

The advantages of QFD is to translate customer need into a technical response. But QFD has some disadvantages related to the difficulties in distinguishing the difference of needs between consumers, difficulties to fulfill the needs of different consumer groups, and the exietence of conceptual gap between consumers and companies. The proposed method to overcome these disadvantages is conjoint analysis. The main advantage of conjoint analysis is the ability to get the optimal design combination for products or services based on consumers' preference. The result of conjoint analysis, estimation of perceived value, and integration of QFD can be used to know the preference market needs among consumers, identify the office desk, determine consumer segments and technical respons, and estimate the additional price of office desk attributes as an effort to the development of the office desk. In overall the best Office desk combination results based on consumers' preference of Office desk is the white color without additional drawers or supporting features, with table size is 120x60x75 cm and footstool. Segmentation based on preferences resulting in three clusters, namely size, color, and availability of drawer. The highest technical response to be the company's priority in meeting the needs of consumers is to make the proper hole connection. Based on the perceived value, the company is capable to predict that the additional prices of 1 drawer is Rp.1-Rp.500.000, the addition price of 2 drawers is Rp.800,000 - Rp.900.000, and the addition price of the foundation of the foot is Rp.50.000 - Rp.150.000, and the additional price of supporting features is Rp.150.000-Rp.250.000.Keywords: Quality Function Deployment (QFD), conjoint analysis, segmentation and perceived value.AbstrakKeunggulan QFD adalah menterjemahkan customer need menjadi respon teknis. Namun QFD mempunyai kekurangan terkait sulit membedakan antara beragam kebutuhan konsumen yang bertentangan, sulit memenuhi kebutuhan konsumen yang berbeda kelompok, dan kesenjangan konseptual antara konsumen dan perusahaan. Untuk melengkapi kekurangan QFD, diusulkan metode conjoint analysis. Keunggulan utama conjoint analysis mampu mendapatkan kombinasi desain yang optimal untuk produk yang melekat pada preferensi konsumen. Hasil integrasi QFD dan conjoint analysis serta estimasi perceived value dapat mengetahui preferensi konsumen meja kantor, mengidentifikasi segmen konsumen meja kantor, menentukan respon teknis, dan mengestimasi harga penambahan atribut meja kantor sebagai upaya pengembangan meja kantor. Secara keseluruhan hasil kombinasi meja kantor terbaik berdasarkan preferensi konsumen meja kantor adalah warna putih, tidak membutuhkan penambahan fitur laci, tidak membutuhkan penambahan fitur pendukung, ukuran meja 120x60x75 cm, dan terdapat tumpuan kaki. Berdasarkan segmentasi preferensi terbentuk tiga klaster, yaitu klaster warna, klaster ukuran, dan klaster ketersediaan laci. Secara keseluruhan respon teknis yang menjadi prioritas perusahaan untuk memenuhi kebutuhan konsumen adalah pembuatan lubang sambungan yang tepat. Berdasarkan hasil perceived value, perusahaan dapat memperkirakan harga penambahan 1 laci berkisar Rp.1 - Rp.500.000, penambahan 2 laci adalah Rp. 800.000 – Rp. 900.000, penambahan tumpuan kaki Rp. 50.000 – Rp. 150.000, dan penambahan fitur pendukung Rp. 150.000-Rp. 250.000.Kata kunci: Quality Function Deployment (QFD), conjoint analysis, segmentasi, dan perceived value

Intuitionistic Fuzzy AHP and WASPAS to Assess Service Quality in Online Transportation Annisa Kesy Garside; Rara Putri Ayuning Tyas; Rahmad Wisnu Wardana
Jurnal Optimasi Sistem Industri Vol. 22 No. 1 (2023): Published in May 2023
Publisher : The Industrial Engineering Department of Engineering Faculty at Universitas Andalas

Indonesia is currently entering a new normal era; this requires people to adapt to the clean-living habit in accordance with health standards in order to carry out normal activities. At the same time, online transportation services have reopened for activity. The service quality provided by online ride-hailing companies (i.e., ojek) such as Gojek, Grab, and Maxim must now consider matters relating to user safety. This study proposes Multi Criteria Decision Making (MCDM) as a method for assessing the service quality of online transportation service providers and uses the Pandemic-SERVQUAL 4.0 model. Pandemi-SERVQUAL 4.0 model adds two new criteria, namely "pandemic" and "industry 4.0". The addition of two new criteria that are more relevant to the current circumstances will increase the accuracy of the research. This study aims to propose the integration of Interval Valued Intuitionistic Fuzzy Analytical Hierarchy Process (IVIF-AHP) to determine the criteria weight and Interval Valued Intuitionistic Fuzzy Weighted Aggregated Sum-Product Assessment (IVIF-WASPAS) to assess the service quality of several online transportation service providers based on the obtained criteria weights. From the results of the service quality assessment using the integration of IVIF-AHP and IVIF-WASPAS, the ranking of online transportation service providers during the new normal era were Grab-car, Go-car, and Maxim-car.

Page 7 of 40 | Total Record : 394

5 6 7 8 9

Filter by Year

2010 2025

Filter By Issues

All Issue Vol. 24 No. 2 (2025): Published in December 2025 Vol. 24 No. 1 (2025): Published in June 2025 Vol. 23 No. 2 (2024): Published in January 2025 (published late, please read our note) Vol. 23 No. 1 (2024): Published in July 2024 Vol. 22 No. 2 (2023): Published in December 2023 Vol. 22 No. 1 (2023): Published in May 2023 Vol. 21 No. 2 (2022): Published in October 2022 Vol. 21 No. 2 (2022): Published in November 2022 Vol. 21 No. 1 (2022): Published in April 2022 Vol. 21 No. 1 (2022): Published in May 2022 Vol. 20 No. 2 (2021): Published in November 2021 Vol. 20 No. 2 (2021): Published in October 2021 Vol. 20 No. 1 (2021): Published in May 2021 Vol. 20 No. 1 (2021): Published in April 2021 Vol. 19 No. 2 (2020): Published in November 2020 Vol. 19 No. 2 (2020): Published in October 2020 Vol. 19 No. 1 (2020): Published in April 2020 Vol. 19 No. 1 (2020): Published in June 2020 Vol. 18 No. 2 (2019): Published in October 2019 Vol. 18 No. 2 (2019): Published October 2019 Vol. 18 No. 1 (2019): Published in May 2019 Vol. 18 No. 1 (2019): Published April 2019 Vol. 17 No. 2 (2018): Published in October 2018 Vol. 17 No. 1 (2018): Published in April 2018 Vol. 16 No. 2 (2017): Published in October 2017 Vol. 16 No. 1 (2017): Published in May 2017 Vol. 16 No. 1 (2017): The Improved JOSI is Published in May 2017 Vol. 15 No. 2 (2016): Published in November 2016 Vol. 15 No. 1 (2016): Published in March 2016 Vol. 14 No. 2 (2015): Published in 1st October 2015 Vol. 14 No. 2 (2015): Published in October 2015 Vol. 14 No. 1 (2015): Published in April 2015 Vol. 13 No. 2 (2014): Published in 1st October 2014 Vol. 13 No. 2 (2014): Published in October 2014 Vol. 13 No. 1 (2014): Published in April 2014 Vol. 12 No. 2 (2013): Published in 1st October 2013 Vol. 12 No. 1 (2013): Published in 1st April 2013 Vol. 12 No. 2 (2013): Published in October 2013 Vol. 12 No. 1 (2013): Published in April 2013 Vol. 11 No. 2 (2012): Published in 1st October 2012 Vol. 11 No. 1 (2012): Published in 1st April 2012 Vol. 11 No. 2 (2012): Published in October 2012 Vol. 11 No. 1 (2012): Published in April 2012 Vol. 10 No. 2 (2011): Published in 1st October 2011 Vol. 10 No. 1 (2011): Published in 1st April 2011 Vol. 10 No. 2 (2011): Published in October 2011 Vol. 10 No. 1 (2011): Published in April 2011 Vol. 9 No. 2 (2010): Published in 1st October 2010 Vol. 9 No. 1 (2010): Published in 1st April 2010 Vol. 9 No. 2 (2010): Published in October 2010 Vol. 9 No. 1 (2010): Published in April 2010 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Rika Ampuh Hadiguna

Contact Email
hadiguna@ft.unand.ac.id

Phone
-

Journal Mail Official
hadiguna@ft.unand.ac.id

Editorial Address
-

Location
Kota padang,

Sumatera barat

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Rika Ampuh Hadiguna

Contact Email hadiguna@ft.unand.ac.id

Phone -

Journal Mail Official hadiguna@ft.unand.ac.id

Editorial Address -

Location Kota padang, Sumatera barat INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Rika Ampuh Hadiguna

Contact Email
hadiguna@ft.unand.ac.id

Phone
-

Journal Mail Official
hadiguna@ft.unand.ac.id

Editorial Address
-

Location
Kota padang,

Sumatera barat

INDONESIA