Claim Missing Document
Check
Articles

Found 23 Documents
Search

FAKTOR-FAKTOR FISIS YANG MEMPENGARUHI AKUMULASI NITROGEN MONOKSIDA DAN NITROGEN DIOKSIDA DI UDARA PEKANBARU Riad Syech; Sugianto '; Anthika '
Komunikasi Fisika Indonesia Vol 10, No 7 (2013)
Publisher : Universitas Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (684.732 KB) | DOI: 10.31258/jkfi.10.7.516-523

Abstract

Telah dilakukan penelitian tentang faktor-faktor fisis yang mempengaruhui akumulasi Nitrogen monoksida dan Nitrogen dioksida di udara Pekanbaru pada stasiun Kulim, Sukajadi dan Tampan dengan menggunakan metodologi interpretasi data. Pengabilan data akumulasi NO dan NO2 konsentrasi NO dan NO2 dilakukan dengan menggunakan alat Nitrogen Oksida Analyzer seri APNA 360 di Laboratorium Udara Kota Pekanbaru. Data yang diamati adalah data harian dari bulan Januari tahun 2010 sampai dengan bulan Desember tahun 2012 . Hasil penelitian menunjukkan bahwa konsentrasi NO dan NO2 tidak pernah sama di setiap bulannya. Konsentrasi terendah NO terdapat di stasiun Kulim sebesar 2,43 μg/m3 pada tahun 2012 dan konsentrasi tertinggi terdapat di stasiun Sukajadi sebesar 55,51 μg/m3 pada tahun 2010. Konsentrasi terendah NO2 terdapat di stasiun Tampan sebesar 3,99 μg/m3 pada tahun 2010 dan konsentrasi tertinggi terdapat di stasiun Sukajadi sebesar 92,99 μg/m3 pada tahun 2010. Suhu, kelembaban udara dan kecepatan angin mempengaruhi besarnya konsentrasi NO dan NO2. Suhu udara yang tinggi, kelembaban udara yang rendah serta kecepatan angin yang tinggi menyebabkan konsentrasi NO dan NO2 rendah, sedangkan suhu udara yang rendah, kelembaban udara yang tinggi dan kecepatan angin yang rendah menyebabkan konsentrasi menjadi tinggi.
EFEK PENAMBAHAN PARTIKEL MAGNETIK Fe3O4 TERHADAP KEMAMPUAN SERAPAN KARBON AKTIF SERBUK GERGAJI KAYU PADA LOGAM BERAT BESI (Fe) Erman Taer; Sugianto '; Rika '
Komunikasi Fisika Indonesia Vol 12, No 11 (2015)
Publisher : Universitas Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (261.464 KB) | DOI: 10.31258/jkfi.12.11.752-758

Abstract

Telah dilakukan study tentang aplikasi karbon aktif magnetik dari serbuk gergaji kayu karet (SGKK) sebagai penyerap logam berat Fe. SGKK diaktivasi menggunakan larutan KOH sebagai aktivator kimia, kemudian SGKK dicampur dengan FeCl3 sebagai prekursor nanopartikel magnetik dan dikarbonisasi pada suhu 850 0 C dalam lingkungan gas Nitrogen (N2). Karakterisasi SEM, EDX, dan XRD bertujuan untuk melihat morfologi permukaan, komposisi kimia, serta strukstur sampel. Hasil pengujian SEM menunjukkan bahwa composite carbon dan nano-Fe3O4 telihat dengan kebera nano-Fe3O4 merata pada permukaan karbon. Pengujian EDX memastikan bahwa partikel yang terdapat pada permukaan karbon adalah unsur Fe3O4. Hasil Uji XRD menunjukkan bahwa logam Fe muncul dengan kehadiran puncak pada ș 360 . Sementara itu, uji kemampuan serapan karbon aktif dilakukan menggunakan SSA. Hasil uji SSA menunjukkan bahwa persentase serapan maksimum pada sampel air sumur bor, air sumur galian dan air sumur bor setelah dilakukan penyaringan berturut-turut adalah sebesar 97,94 %, 83,58 %, dan 56,18%.
PEMANFAATAN POTENSI TANDAN KOSONG KELAPASAWIT SEBAGAI KARBON AKTIF UNTUK PEMBERSIHAIR LIMBAH AKTIVITAS PENAMBANGAN EMAS Erman Taer; Widya Sinta Mustika; Sugianto '
Komunikasi Fisika Indonesia Vol 13, No 13 (2016)
Publisher : Universitas Riau

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (418.808 KB) | DOI: 10.31258/jkfi.13.13.852-858

Abstract

Pemanfaatan biomassa sebagai karbon aktif untuk aplikasi pembersih air limbah dapat dilakukan dengan kombinasi metode aktivasi dan karbonisasi. Karbon aktif dibuat dari tandan kosong kelapa sawit (TKKS) melalui beberapa tahap pengolahan tongkol menjadi pelet karbon, kemudian dilakukan proses karbonisasi pada suhu 800 0 C di lingkungan gas Nitrogen (N2). Aktivasi kimia menggunakan larutan KOH sebagai aktivator. Metode Scanning Electron Microscopy (SEM) digunakan untuk menganalisa struktur dan morfologi permukaan pelet karbon aktif TKKS. Sementara komposisi unsur kimia penyusun sampel yang dianalisa menggunakan Energy Dispersif X-Ray (EDX). Uji kemampuan serapan karbon aktif terhadap logam berat dilakukan menggunakan Spektrofotometer Serapan Atom (SSA). Dari spektrum EDX menunjukkan kehadiran unsur karbon (C) 79,79 %, sedangkan kontaminasi maksimum logam Fe 2,36 % dan Zn 0,61 %. Dari pengujian serapan logam berat berdasarkan SSA diperoleh hasil bahwa serapan optimum untuk Fe 78,52 % dan Zn 77,23 %, sehingga hasil penelitian menunjukkan bahwa pelet karbon aktif TKKS memiliki daya serap yang lebih tinggi terhadap logam berat besi (Fe).
PENENTUAN BESAR ENERGI LISTRIK AKI DENGAN MEMVARIASIKAN JUMLAH AIR SULING (H2O) DAN ASAM SULFAT (H 2SO4 ) Romadona '; Maksi Ginting; Sugianto '
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 1, No 2 (2014): Wisuda Oktober 2014
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

A research has been conducted to determine electrical energy  of accu   with variation of volume  of distilled water and sulfuric acid. In this study, an  electrolyte solution  of 400 ml  was prepared  for each accu  consisting of a mixture of distilled water and sulfuric acid with different compositions.  Measurements  of each sample  were  carried out at  the interval time of  15 minutes for 2 hours. The results showed that the  amount of  energy produced by  accu  with a standard electrolyte solution  expenses  factory for 2 hours  was 114.14   kilojoules. The amounts  of  energy  obtained  from the  variation of  the mixture composition  of the electrolyte solution  ratio  were  154.23  kilojoules, 156.73  kilojoules, and  141.61 kilojoules, respectively for a mixture of distilled water and sulfuric acid witha composition ratio  of  64% :  36%, 60% :  40%,  and  70% : 30%,  where  as  for a mixed electrolyte solution with  aquabides and  sulfuric acid,  resulted the energy of  164.18 kilojoules, 157.37 kilojoules, and  148.52 kilojoules, respectively for the mixture ratio of 64%  : 36%, 60%  : 40%,  and  70%  : 30%.  Conclusion,  the  largest energy   produced  was obtained  by the  accu with  electrolyte solution  containing a  mixture of  sulfuric  acid  and  aquabides with the composition ratio of 64% : 36%.
RANCANG BANGUN ALAT PENJERNIH AIR YANG TERCEMAR LOGAM BERAT Fe, Cu, Zn DALAM SKALA LABORATORIUMRANCANG BANGUN ALAT PENJERNIH AIR YANG TERCEMAR LOGAM BERAT Fe, Cu, Zn DALAM SKALA LABORATORIUM Andi Syahputra; Sugianto '; Riad Syech
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 2, No 1 (2015): Wisuda Februari 2015
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

A research on design and construction of purification equipment of water contaminated by heavy metals Fe, Cu, and Zn was carried out. The equipment was utilized to purify water sample of Siak River at a distance of 1m from the PT. RICRY of rubber industry in Pekanbaru. Analysis was performed by using Atomic Absorption Spectrophotometer (AAS). The analysis results showed that the concentration of Cu, Fe and Zn before filtration process sequentially were 0.3809 ppm, 0.0051 ppm, and -0.0012 ppm. After being filtered twice showed an absorption percentage for type I sieve (with carbon) on the heavy metals sequentially were Fe 75%, Zn 14.29% and Cu 10.78%. Sieve type II (without carbon) absorption percentage of each heavy metal were Fe 59.5%, Zn 7.75%, and Cu 0.0%, while the water discharge at the sieve type I (with carbon) obtained an average water discharge of 0.164 645 x 10-2 m3/s, and the sieve type II (without carbon) of 0.17838 x 10-2 m3/s. Based on the result the sieve type I with carbon has a better result for water purification treatment.
PERBANDINGAN KANDUNGAN LOGAM BERAT (Cu, Fe dan Zn) PADA AIR SUNGAI SIAK SEBELUM DAN SESUDAH PROSES PENJERNIHAN Rutmayanti Pandiangan; Sugianto '; Usman Malik
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 1, No 2 (2014): Wisuda Oktober 2014
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Comparison  of heavy metal  (Cu,  Fe  and  Zn)  content of Siak  river water  between before and after purification process has been done using an experimental method. The processstarted  by taking  sample of  the Siak River  water  at a distance of  1  meter  from  waste sewage system  of  rubber  manufacturing industry  PT.RICRY  Pekanbaru.  Concentration of pre-filtered  samples  was measured by  atomic absorption  spectrophotometer  (AAS), then each sample  was  filtered five times.  The result of pre-filtered samples characterized by  (AAS) of  Cu,  Fe  and  Zn  were  0.3809  ppm,  0.0051  ppm,  and  -0.0012 ppm.  The absorption percentage  of samples  characterized by  (AAS) for Fe, Zn and Cu were 12,02 %, 33,33 % and 72,54 %,  respetively (type I) and 33,15 %, 2,70 % and 80,39 % respetively for type II.  Based on the  obtained data,  it was concluded  that  the purity instrument  of  type I  was better  than  type II  for  water treatment.
KARAKTERISTIK SPEKTRUM KEBISINGAN KENDARAAN SAAT BERHENTI Dewi Muliana; Juandi '; Sugianto '
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 2, No 1 (2015): Wisuda Februari 2015
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The Characteristics of Noise Spectrum for Vechicle at Rest condition at Jalan Soekarno Hatta, Pekanbaru, Indonesia. The research methodology uses Digital Voice Recorder experimentally and a GoldWave Software computes by a recorder. The measurement of noiseis detected at rest vehicle in four position having densed noise. First position has high peak and amplitude at Jalan Tuanku Tambusai 1. The other positions have low peak and amplitude at Jalan Soekarno Hatta 1, Jalan Tuanku Tambusai 2 and Jalan Soekarno Hatta 2 respectively. Noise signal is then evaluated at frequency 20 Hz - 20,000 Hz for all position. The intensityat position I has -85.0584 dB until -29.4942 dB, position II has -47.7043 dB until -84.5914dB , position III has -74.7860 dB until -46.7704 dB and position IVhas -74.7860 dB until - 46.3035 dB. The average noise spectrum intensity of vehicle against frequency y=Ax+B, where y is avarege spectrum intensity and x is frequency. The details is at position I (y=- 0.002x-35.93), at position II (y=-0.001x-52.01), at position III (y=-0.000x-54.81) and at position IV (y=-0.001x-50.24). In conclution, the spectrum of vehicle stop condition has low intensity.
ANALISA DISPERSI MATERIAL SERAT KISI BRAGG MENGGUNAKAN METODE SOFTWARE OPTIGRATING Elisa Saadah; Saktioto '; Sugianto '
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 2, No 1 (2015): Wisuda Februari 2015
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The analysis of material dispersion on Fiber Bragg Grating (FBG) by using silica material for the core and cladding with germania-doped silica material has been determined. FBG is used for multi mode. Parameters that fluctuate in this study is the grating length of FBG while the value of the period, the modulation index and the amount of grating is keptconstant.   The method used is OptiGrating software, which is a software evaluating a transfer matrix to analyze the grating on the FBG. The results showed the higher value of long-grating given in FBG, the lower valley formed transmission coefficients. The pattern of the transmission coefficients of FBG found the difference between FBG dispersed material and no dispersed material. The dispersed material produced some FBGtransmission coefficients with a certain value where the bigger one has the pattern point value the lower the transmission coefficients is produced. The FBG with no  material dispersion results the constant of the transmission coefficients.
SISTEM PEMANAS AIR ENERGI SURYA MENGGUNAKAN KOLEKTOR PALUNG PARABOLA POSISI TIMUR-BARAT Martha Rianna; Maksi Ginting; Sugianto '
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 2, No 1 (2015): Wisuda Februari 2015
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Heating System of Solar Energy by using Parabolic Trough Collector of East West Position has been experimentally conducted. The collector is set at open air from the sun radiation and observed every 60 minutes from 9 AM until 3 PM for bright sunshine. After 14 days, the results show that the collector temperature has a minimum average of collector 40,290C and water tank 36,070C at 10 AM, whereas the highest average temperature is 51,260C and water tank 45,570C at 1 PM. The observation describes the highest temperature at collector tank occurs at 1 PM due to the highest radiation intesity to the collector reaching maximum value of 448 W/m2. Loss heat by conduction at lowest rate is 23,50 J/s at 10 AM whereas loss heat by conduction at highest rate 36,60 J/s at 1 PM. The average water volume is 39 liters for 6 hours daily from 9 AM until 3 PM. Overall, the higher radiation intensity from the sun to heat the collector, the higher water temperature observed in the collector tank.
PENENTUAN EFISIENSI KOLEKTOR PELAT DATAR DENGAN PENUTUP KACA PADA SISTEM PEMANAS AIR SURYA Zelviana '; Maksi Ginting; Sugianto '
Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam Vol 1, No 2 (2014): Wisuda Oktober 2014
Publisher : Jurnal Online Mahasiswa (JOM) Bidang Matematika dan Ilmu Pengetahuan Alam

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

A  research has been conducted to determine the efficiency of flat plate collector  with  its cover  made from  glass. Solar water heaters  were  made  and  comprised of five essential components, namely a  protective box,  a  plate absorbent,  an  insulator,  an  iron pipe, and a  transparent cover. In this study, the water  was flown  into the water tank, through  a  collector, and then  the  water  flowed  into a  tube  collectors.  The  collectors  used  in this  study  were  flat plate  collectors  with one and two layer lid.  The  data  was  collected  within 14 days,  starting from  9.00 am until  3.00 pm  WIB  with one hour time interval.  The average  efficiency  for  a single  layer collector  was  42.62 % to 62.14 % , and for the two layer collectors  was  51.69 % to 85.74 % . These results  showed that the loss of heat on a flat plate collector with two layer was smaller than those of a single layer collector.