Claim Missing Document
Check
Articles

Performance Evaluation of 3-RRPaR Parallel Manipulator in Pick and place Operation Anrinal Anrinal; Randa Randa; Asmara Yanto
Jurnal Teknik Mesin Vol 15 No 1 (2025): Jurnal Teknik Mesin Vol.15 No.1 April 2025
Publisher : ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21063/jtm.2025.v15.i1.1-7

Abstract

This study evaluates the performance of a 3-RRPaR parallel manipulator designed to perform pick-and-place operations. The manipulator consists of three actuators driven by stepper motors, which are controlled through a G-code interface using Universal G-Code Sende.. Motion commands are input via a computer, enabling the robot to follow predefined trajectories. During testing, the manipulator was programmed to move within a circular workspace with a radius of 100 mm on the X and Y axes. The actual movement reached only 98 mm, resulting in a positioning error of approximately 2 mm. The observed inaccuracies are primarily attributed to structural inconsistencies between the upper and lower frames, unequal lengths of the passive links, and the use of a non-permanent clutch mechanism. These findings highlight the importance of mechanical precision and structural symmetry in enhancing the accuracy of parallel manipulator systems.
Structural Evaluation and Optimization of a Peanut Shelling Machine Frame Using Finite Element Analysis M. Ibnu Hakim; Anrinal Anrinal; Asmara Yanto
Jurnal Teknik Mesin Vol 15 No 2 (2025): Jurnal Teknik Mesin Vol.15 No.2 October 2025
Publisher : ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21063/jtm.2025.v15.i2.47-55

Abstract

This study investigates the structural integrity of a peanut shelling machine frame with a capacity of 60 kg/hour using Finite Element Analysis (FEA) in SolidWorks. Two configurations of ASTM A36 angle steel profiles—40×40×3 mm and 20×20×3 mm—were evaluated with a frame geometry of 906×600×900 mm. Operational loads were applied to three critical zones with aggregate weights of 82.6 kg, 5.3 kg, and 13.1 kg, respectively. The structural response was assessed through von Mises stress distribution, nodal displacement, and safety factor analysis. Results indicate that the 40×40×3 mm frame exhibits a maximum stress of 37.114 MPa, displacement of 0.2431 mm, and a safety factor of 6.7, while the 20×20×3 mm frame shows a maximum stress of 73.978 MPa, displacement of 0.4521 mm, and a safety factor of 3.4. Both designs satisfy structural safety requirements, maintaining stresses below the material yield strength of 250 MPa and safety factors above the minimum threshold of 2.0. Stress concentrations were predominantly observed at frame corners. While the smaller profile reduces material usage by 50%, it also decreases stiffness by 86%. The findings demonstrate that the 20×20×3 mm configuration is a cost-effective alternative for static loading conditions, whereas the 40×40×3 mm frame provides higher rigidity suitable for potential dynamic load scenarios.
Design and Structural Performance Evaluation of a CNC Plasma Cutting Machine Frame Asmara Yanto; Aga Pratama; Anrinal Anrinal; Putri Pratiwi
Jurnal Teknik Mesin Vol 15 No 1 (2025): Jurnal Teknik Mesin Vol.15 No.1 April 2025
Publisher : ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21063/jtm.2025.v15.i1.8-14

Abstract

Plasma cutting is a widely used process for cutting metal plates using a high-temperature electric arc. Conventional systems are manually operated, which limits cutting precision and efficiency. To address this, a CNC plasma cutting machine was designed with a focus on structural reliability. The machine frame was designed to support automated motion along X, Y, and Z axes, enabling precise plasma head movement. The overall machine dimensions are 3000 mm × 1500 mm × 1000 mm, with a work area of 2400 mm × 1200 mm. Structural components were modeled using CAD software and analyzed using the Finite Element Method (FEM) to evaluate deformation, stress distribution, and safety factors. The structural analysis revealed maximum displacements of 4.14 µm and 3.83 µm in the X and Y units, respectively. The highest von Mises stress was found to be 56.57 MPa on the X unit and 50.19 MPa on the Y unit. The minimum safety factors were 4.41 for the X unit and 2.36 for the Y unit, indicating a safe and robust structural design. The results confirm that the designed machine frame meets mechanical integrity requirements for automated plasma cutting operations. The low deformation and acceptable stress levels ensure cutting accuracy and operational reliability. This design may serve as a foundation for future improvements or implementation in manufacturing environments.