Claim Missing Document
Check
Articles

Found 19 Documents
Search

APLIKASI NERACA AIR UNTUK MENENTUKAN BULAN BASAH DAN KERING DI KOTA PALEMBANG Sugiarto, Ari; Suharnoto, Yuli; Kurniawan, Allen
Jurnal Ilmiah Desain & Konstruksi Vol 19, No 1 (2020)
Publisher : Universitas Gunadarma

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35760/dk.2020.v19i1.3493

Abstract

Ketersediaan air di suatu wilayah dapat digambarkan dengan analisis neraca air. Prinsip analisis ini berdasarkan ketersediaan air hujan setelah dikurangi kehilangan air dari proses evapotranspirasi. Berdasarkan deskripsi tersebut, studi ini bertujuan untuk menentukan bulan basah dan kering di Kota Palembang menggunakan analisis neraca air dari data curah hujan dan evapotranspirasi. Studi ini menggunakan data selama 10 tahun terakhir (2010-2019) diperoleh dari dua stasiun Badan Meteorologi, Klimatologi, dan Geofisika (Kenten dan Sultan Mahmud Badaruddin II) di Kota Palembang. Proyeksi nilai evapotranspirasi menggunakan model Penman-Monteith. Tahapan analisis meliputi akumulasi dan polinomial orde 6, penurunan, dan pengurangan dari curah hujan dan evapotranspirasi. Hasil analisis data iklim dari stasiun Kenten menunjukkan rata-rata bulan basah dalam 10 tahun terakhir terjadi pada 1-166 dan 273-365 J-day, sedangkan bulan kering terjadi pada 167-272 J-day. Analisis data iklim dari Stasiun Sultan Mahmud Badaruddin II menunjukkan bulan basah terjadi pada 1-161 dan 284-365 J-day, sedangkan bulan kering tejadi pada 162-283 J-day. Analisis data dari stasiun Sultan Mahmud Badaruddin II menunjukkan waktu bulan basah yang lebih pendek dan bulan kering yang lebih panjang 15 hari dibanding Stasiun Kenten. Namun, kedua hasil dari stasiun tersebut menunjukkan bahwa bulan basah di Kota Palembang terjadi pada awal Januari hingga pertengahan Juni dan awal Oktober hingga akhir Desember, sedangkan bulan kering terjadi pada pertengahan Juni hingga awal Oktober.
Desain instalasi pengolah limbah WC komunal masyarakat pinggir sungai desa Lingkar Kampus Asep Sapei; M. Yanuar J. Purwanto; . Sutoyo; Allen Kurniawan
Jurnal Ilmu Pertanian Indonesia Vol. 16 No. 2 (2011): Jurnal Ilmu Pertanian Indonesia
Publisher : Institut Pertanian Bogor

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1642.518 KB)

Abstract

Cangkurawok Village is located in the outer of the Bogor Agricultural University area and does not have good sanitation facilities. Disposal of domestic wastewater directly discharges into drainage channels to river. Wastewater treatment plant design from toilets communal divides into three stages. The first stage is determining the location of toilets communal and excreta treatment plant. Location provided by the public is around 5 meters above the surface of the river water. The second stage is the determination of service areas. In this village consists of 70 heads of households as the basic criteria for determining the volume of septic tanks. The last step is determining the design of toilets communal and wastewater treatment unit. This stage requires t he unit options that fits on the selected sites, based on ease of maintenance and no need employ trained operators. Waste treatment facility consists septic tank and infiltration well planning. Septic tank volume is 26.5 m3 with the long dimension of 2.75 m, width of 5.5 m and height of 1.5 m plus 0.3 meters for free board. Septic tank serving four toilets communal is built above it, with the division of space for two men and two spaces for women. infi lt rat ion well constructed to absorb the waste liquid vertically through the soil pores. Layers of sand and gravel is spread throughout the wells to assist the flow pattern. Depth and diameter of infiltration well are 3 m and 1 rn, This wells should be placed lower than the drinking water sources and wells, with a minimum distance of 15 m.
MODEL ESTIMASI BIOKINETIKA UNTUK PROSES POST-DENITRIFIKASI AIR LIMBAH DOMESTIK PADA UNIT ANAEROBIC BAFFLED REACTOR Allen Kurniawan; Fatihaturrizky Amelia; Adhirajasa Wirayudhatama; Sulpa Yudha Prawira
JURNAL SUMBER DAYA AIR Vol 17, No 2 (2021)
Publisher : Bina Teknik Sumber Daya Air, Kementerian Pekerjaan Umum dan Perumahan Rakyat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32679/jsda.v17i2.701

Abstract

This study developed a combination of Continuous Stirred Tank Reactor (CSTR) for the acid fermentation and the Anaerobic Baffled Reactor (ABR) post-denitrification through high nitrite injection. Volatile Fatty Acids (VFAs) as a substrate for the post-denitrification process were optimally produced in the acid fermentation process. The aim of this study was to obtain the estimation of biokinetic values to predict the effluent wastewater quality in ABR post-denitrification process under unsteady state. The reactor was operated for HRT 7 days at temperature 25-28 ˚C and pH 6-7,2. The influent and effluent substrate concentration were monitored continuously for 160 days. Post-denitrification biokinetic from the Contois equation resulted in the value of hydrolysis rate (Kh) of 0.077 day-1, the substrate transport rate (k) of 4.364×10-6 Lmg-1day-1, maximum specific growth rate (μmax) of 0.559 day-1, half saturation constant (KS) of 0.209 mgL-1, microbial decay coefficient (b) of 0.0145 days-1; yield coefficient (Y) of 0.084 g-VSSg-COD-1. The validation of biokinetic parameters based on statistical analysis showed fairly precise results following the trend of experimental data to determine the substrate concentration in the effluent unit. Therefore, the biokinetic values can be applied in the design of ABR post-denitrification using primary sludge incorporation with high strength nitrate.Keywords:  Anaerobic baffled reactor, biokinetics, Contois, hydrolysis, post-denitrification.
Estimasi Nilai Hydraulic dan Solid Loading Rate Tipe Pengendapan Diskrit dan Flok Pada Proses Lumpur Aktif Untuk Pengolahan Limbah Cair Industri Kertas Fatihaturrizky Amelia; Owen Jacob Notonugroho; Satyanto Krido Saptomo; Allen Kurniawan
Jurnal Ilmu Lingkungan Vol 20, No 3 (2022): July 2022
Publisher : School of Postgraduate Studies, Diponegoro Univer

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/jil.20.3.445-456

Abstract

Beban limbah cair industri kertas meningkat seiring dengan peningkatan produksi kertas di Indonesia. Konsentrasi COD berkisar antara 8.300–45.384 mg/L O2 dan TSS sebesar 41.000 mg/L. Salah satu upaya untuk mengurangi beban COD dan TSS di dalam limbah cair industri kertas adalah dengan memanfaatkan proses lumpur aktif. Penelitian ini difokuskan pada pengaruh proses sedimentasi di dalam unit lumpur aktif untuk mereduksi COD dan TSS. Penelitian ini juga mencakup analisis dua tipe pengendapan, yaitu pengendapan partikel diskrit dan pengendapan flok. Tujuan utama penelitian ini untuk mengestimasi nilai hydraulic loading rate dan solid loading rate serta rekomendasi dimensi unit sedimentasi lumpur aktif. Penelitian ini meliputi kegiatan monitoring kinerja proses dengan tiga variasi waktu detensi (HRT). Beberapa variabel yang diperhatikan untuk mencapai tujuan penelitian ini, antara lain kecepatan pengendapan bebas (v), percepatan gravitasi (g), massa jenis partikel (ρs), massa jenis fluida (ρ), diameter partikel (d), dan koefisien penarikan atau drag coefficient (Cd). Pengukuran reduksi COD mengacu pada SNI 6989.2:2009 dan pengukuran reduksi TS mengacu pada SNI 06-6989.26-2005. Penelitian ini menunjukkan bahwa kecepatan pengendapan discrete particle settling tergantung pada karakteristik satuan partikel berdasarkan diameter partikel. Kecepatan pengendapan flocculant settling tergantung pada pengaruh interaksi partikel dalam pembentukan flok atau gumpalan beberapa entitas partikel. Jika ditinjau dari nilai umur lumpur (SLR), HRT 8 jam dan HRT 12 jam menunjukkan kondisi under loaded pada unit sedimentasi. Sementara itu, nilai HLR dan SLR pada HRT 6 jam telah memenuhi rentang kriteria desain lumpur aktif. Dengan demikian, desain terbaik untuk unit sedimentasi sekunder lumpur aktif, yaitu HRT 6 jam dengan HLR sebesar 42,16 m3/m2hari, SLR sebesar 102,45 kg/m2hari dan rata-rata reduksi padatan total mencapai 89,26%.ABSTRACTThe influence of paper production affect simultenously to the increase of pulp and paper wastewater in Indonesia. The COD concentration ranged from 8,300–45,384 mg/L O2 and TSS was 41,000 mg/L. Reducing COD and TSS concentrations in the paper industry wastewater is to utilize by using activated sludge processes. This research was focused on the effect of sedimentation process in activated sludge to reduce COD and TSS. This research also included the analysis of two types of deposition, namely discrete particle settling and floc settling. Main objective this research was directed at determining the value of the hydraulic loading rate and solid loading rate as well as recommendations for the dimensions of the activated sludge sedimentation unit. This research included monitoring of process performance with three variations of detention time (HRT). There were several variables that are considered to achieve the objectives of this study, including free deposition velocity (v), acceleration due to gravity (g), particle density (ρs), fluid density (ρ), particle diameter (d), and drag coefficient. coefficient (Cd). The COD and TS reduction measurement refered to SNI 6989.2:2009 and SNI 06-6989.26-2005, respectively. This study showed that the speed of discrete particle settling depends on the characteristics of the particle unit as seen from the particle diameter. The deposition rate of flocculant settling depends on the effect of particle interactions in the formation of flocs or agglomerates of several particle entities. When viewed from the SLR value obtained, the 8-hour HRT and 12-hour HRT indicated that the sedimentation unit was in an under-loaded condition. Meanwhile, the HLR and SLR values at HRT 6 hours complied the activated sludge design criteria. Thus, the best design for the activated sludge secondary sedimentation unit was HRT 6 hours with an HLR of 42,16 m3/m2day, an SLR of 102,45 kg/m2day and an average total solids reduction of 89,26%.
Hidrokarbon Aromatik Polisiklik pada Lahan Tercemar Limbah Minyak Bumi: Tinjauan Pertumbuhan Mikro-Organisme, Proses Metabolisme dan Biodegradasi Allen Kurniawan; Yanuar Chandra Wirasembada; Indah Mutiara Ningtyas Razaad; Adi Novriansyah; Mohamad Rafi; Agus Jatnika Effendi
Jurnal Ilmu Lingkungan Vol 16, No 1 (2018): April 2018
Publisher : School of Postgraduate Studies, Diponegoro Univer

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.4 KB) | DOI: 10.14710/jil.16.1.9-24

Abstract

ABSTRAKHidrokarbon Aromatik Polisiklik (HAP) berasal dari proses alamiah dan limbah antropogenik di lingkungan. HAP merupakan polutan di udara, tanah, dan padatan yang mengendap pada fase cair (sedimen) dan berkembang akibat pembakaran tidak lengkap material organik. Kajian ini berupa studi literatur mengenai informasi secara lebih detil tentang laju kenaikan HAP pada tanah, gambaran umum proses metabolisme, proses biodegradasi HAP melalui keterlibatan mikroorganisme, dan alternatif pengolahan sebagai media teknologi penunjang aktivitas proses degradasi. Proses degradasi HAP dan substrat hidrofobik digunakan untuk membatasi jumlah fase cair terlarut melalui sorbsi, kristalin, dan non-aqueous phase liquid (NAPL) sehingga HAP terlarut menjadi tidak tersedia. Laju peningkatan HAP di dalam tanah terbagi atas tiga fase, yaitu fase eksponensial, fase lanjutan dengan pertumbuhan pseudo-linear, dan fase pseudo-stasioner pada kondisi tidak ideal berdasarkan ciri akses bakteri tersedia dalam jumlah tidak terbatas, dan transportasi substrat adalah homogen. Pada media heterogen, seperti tanah, HAP diserap dalam partikel organik pada pori-pori dengan ukuran kecil sehingga bakteri tanah tidak dapat mengakses HAP. Pada kasus pencemaran dalam skala besar, HAP akan berbentuk semacam tar droplet sehingga membatasi bakteri untuk mendegradasi HAP. Selain bakteri, jenis organisme dan mikroorganisme spesifik pendegradasi HAP dapat ditemukan pada jamur (fungi), cyanobacteria, dan alga.Kata kunci: biodegradasi, hidrokarbon aromatik polisiklik, mikroorganisme, proses metabolisme.ABSTRACTPolycylic Aromatic Hydrocarbons (PAHs) are derived from natural processes and the anthropogenic wastes in the environment. PAHs are pollutants found in the air, soil, and sediments which are developed due to incomplete combustion of the organic materials. This review provides a more detail literature study regarding the microbial growth, the metabolic process, and PAHs microbial biodegradation processes overview. The process of PAHs and the hydrophobic substrate degradation is applied to limit the amount of dissolved aqueous phase through sorption, crystalline, and non-aqueous phase liquid (NAPL) so that the dissolved PAHs are no longer available. microbial growth on PAHs as the sole carbon source can be divided into three phases which are the exponential phase, the advance phase with pseudo-linear growth, and pseudo-stationery phase in a non-ideal condition based on the characteristic of the unlimited bacterial access and the homogenous substrate transport. In the heterogeneous medium, such as soil, PAHs are absorbed into the organic particles of small sized pores so that the PAHs become inaccessible for the soil bacteria. In large scale pollution, the PAHs are in the form of tar droplets which limit the access for soil bacteria to degrade the PAHs. Other than bacteria, the specific organisms and microorganisms to degrade PAHs are found in fungi, cyanobacteria, and algae.Keywords: biodegradation, growth rate, metabolic process, microbial, polycyclic aromatic hydrocarbons.Citation: Kurniawan A., Wirasembada, Y.C., Razaad, I.M.N., Novriansyah, A., Rafi, M., Effendi, A.J.(2018). Hidrokarbon Aromatik Polisiklik pada Lahan Tercemar Limbah Minyak Bumi: Tinjauan Pertumbuhan Mikro-Organisme, Proses Metabolisme dan Biodegradasi, Jurnal Ilmu Lingkungan, 16(1), 9-24, doi:10.14710/jil.16.1.9-24
Efek Kecepatan Pengendapan terhadap Perencanaan Unit Sedimentasi Primer pada Pengolahan Air Lindi Owen Jacob Notonugroho; Muhammad Faiz Kahendran; Aliyah Baida Wiwiyanti; Dzaki Nauval; Chusnul Arif Arif; Allen Kurniawan
Jurnal Teknik Sipil Institut Teknologi Padang Vol 9 No 2 (2022): Jurnal Teknik Sipil Institut Teknologi Padang
Publisher : ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (477.528 KB) | DOI: 10.21063/jts.2022.V902.03

Abstract

Produksi air lindi akibat tumpukan sampah akan mencemari lingkungan dan air tanah di bawahnya apabila tidak diolah dengan baik. Air lindi memiliki banyak padatan tersuspensi sehingga memerlukan koagulan sebagai pengikat antar partikel padatan. Penelitian ini merancang unit sedimentasi primer dengan mempertimbangkan kecepatan pengendapan ketika diberi koagulan. Berdasarkan hasil pengujian jar test diperoleh dosis optimum PAC 2500 mg/L karena memiliki nilai turbiditas dan COD terkecil berturut-turut sebesar 0.46 NTU dan 163 mg/L. Dosis koagulan terpilih selanjutnya dilakukan pengukuran hindered settling sehingga menghasilkan nilai ketinggian kritis 15,9 cm dan waktu kritis 76,7 menit. Proses pengendapan zona kompresi terjadi pada menit ke-183 ditandai dengan melandainya kurva. Desain unit sedimentasi primer berdasarkan karakteristik kecepatan pengendapan pada air lindi dapat mengadopsi persamaann Vesilind dan Yoshida-Dick. Nilai koefisien pengendapan dengan persamaan Vesilind dan Yoshida-Dick masing-masing sebesar 2 × 10-6  m3/gr  dan 9,82 × 10-3 m3/gr. Persamaan Vesilind menghasilkan nilai kecepatan pengendapan sebesar 0,009 cm/detik, sedangkan persamaan Yoshida dan Dick sebesar 0,01 cm/detik. Berdasarkan kurva hindered diperoleh nilai Hu sebesar 5,23 cm dan Tu sebesar 183,74 menit. Nilai Hu dan Tu dapat memperoleh nilai SOR sebesar 2,39 m3/m2. Debit aliran ditentukan sebesar 100 L/detik maka diperoleh nilai luas area permukaan sedimentasi sebesar 3614,74 m2 dan diameter unit sedimentasi diperoleh sebesar 66,67 m. Kedalaman total dan diameter unit sedimentasi primer diperoleh sebesar 4,59 m dan 66,67 m. Desain struktur unit sedimentasi terdiri atas struktur influen, orifice submerge EDI, dan struktur efluen agar debit influen yang memasuki unit sedimentasi tidak mengganggu proses pengendapan. Hubungan antara nilai pemodelan kecepatan pengendapan dengan desain unit sedimentasi diharapkan mampu mengoptimumkan proses pengendapan pada air lindi dengan menggunakan koagulan PAC.
Pengaruh Sudut Inklinasi Plate-Settler terhadap Kecepatan Vertikal Proses Sedimentasi pada Pengolahan Limbah Cair Kertas Fatihaturrizky Amelia; Oktavian Wahyu Pratama Ajie; Allifiya Salsabil Nugrohoputri; Nurwahid Dimas Saputro; Allen Kurniawan
Semesta Teknika Vol 25, No 2 (2022): NOVEMBER 2022
Publisher : Universitas Muhammadiyah Yogyakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.18196/st.v25i2.15223

Abstract

Pengolahan limbah cair industri kertas memberikan produk kontaminan yang berbahaya ketika dibuang ke lingkungan tanpa pengolahan. Beban kontaminan yang tinggi memberikan efek terhadap beratnya beban pengolahan limbah secara biologis. Kecepatan pengendapan merupakan salah satu komponen terpenting di dalam meningkatkan kinerja unit sedimentasi, antara lain melalui penggunaan plate-settler. Penelitian ini bertujuan menganalisis pengaruh penambahan plate-settler dalam berbagai variasi inklinasi. Metode penelitian ini dilakukan melalui pengamatan terhadap kecepatan jatuh partikel, dan estimasi kecepatan jatuh yang dipengaruhi oleh sudut inklinasi platesettler pada unit sedimentasi. Karakteristik limbah cair industri kertas menunjukkan kecenderungan membentuk flok dan memiliki kemampuan pengendapan yang tinggi yang ditunjukkan oleh penurunan lumpur sebesar 29,53 cm pada 2,5 menit pertama. Modifikasi mekanisme pengendapapan dapat menambahkan plate-settler untuk meningkatkan efisiensi reduksi partikel dengan sudut optimum sebesar 60o hingga 75o. Nilai ini menunjukkan sudut inklinasi plate-settler yang memengaruhi mekanisme penyisihan total padatan di dalam proses seimentasi, selain kecepatan vertikal partikel.
Estimation Of Disharge Coefficient On Weir Configuration Based On Flow Rate And Velocity Khusnita Azizah; Nurwahid Dimas Saputro; Budi Indra Setiawan; Allen Kurniawan
Applied Research on Civil Engineering and Environment (ARCEE) Vol. 4 No. 01 (2023)
Publisher : POLITEKNIK NEGERI JAKARTA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32722/arcee.v4i01.4874

Abstract

The development of water treatment and water resources considers the flow rate adjusted using a weir. Weir is designed with many hydraulic factors, including the coefficient of discharge (Cd). Characteristics of the value of Cd show a decreasing trend on triangular and rectangular weirs. The value of Cd varies based on the flow's characteristics and the channel's geometry. Estimation of the best Cd value in flow discharge engineering and sediment deposition is necessary to know the accuracy of weir geometry. Some plans in water treatment and water resource building sometimes assume a Cd value based on literature. This study aims to estimate the value of Cd based on variations in flow rate and was conducted on a laboratory scale with weir shape limitations in the form of triangles and rectangles. The water sample was discharged by a water pump into an open channel. The angle of the weir opening was determined for the rectangular and triangular weir of 90°. Flow monitoring included flow discharge through the use of a current meter. Water was recycled in each measurement with a total of 60 cycles. The Cd values in a triangular weir were greater than in a rectangular weir. The Cd values for the rectangular weir ranged from 0.068 to 0.089, while the Cd values for the triangular weir ranged from 0.557 to 0.598. This value indicated that the greater the flow rate, the lower the Cd value. Therefore, weir configuration of water discharged using a triangular weir was better than a rectangular weir at low flow rates, less than 0.05 m3/s.
KAJIAN PENGARUH PENGGUNAAN LUMPUR MINYAK TERHADAP KONSENTRASI TOTAL PARTIKULAT TERSUSPENSI (TSP) DAN SULFUR DIOKSIDA (SO2) DARI EMISI TANUR PUTAR INDUSTRI SEMEN (Assessment of Oil Sludge Utilization Influence on Total Suspended Particulate) Rofie Fatimah; Allen Kurniawan; Arief Sabdo Yuwono
Jurnal Manusia dan Lingkungan Vol 21, No 3 (2014): November
Publisher : Pusat Studi Lingkungan Hidup Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/jml.18552

Abstract

ABSTRAKIndustri semen merupakan industri padat energi dengan memanfaatkan bahan bakar fosil. Beberapa pabrik semen mencari sumber energi alternatif mengingat cadangan bahan bakar fosil terbatas dengan harga yang meningkat. Di sisi lain, pengelolaan limbah sangat dibutuhkan sebagai dampak dari aktivitas perindustrian. Co-processing merupakan salah satu upaya untuk mengatasi permasalahan tersebut dengan memanfaatkan limbah industri sebagai sumber energi baru. Salah satu limbah yang dapat dimanfaatkan adalah lumpur minyak. Atas dasar deskripsi tersebut, tujuan penelitian ini untuk membandingkan konsentrasi Total Partikulat Tersuspensi (TSP) dan sulfur dioksida (SO2) yang diemisikan dari tanur industri semen saat menggunakan bahan bakar utama (batu bara) dan batu bara yang digabung dengan lumpur minyak, membandingkan konsentrasi setiap kondisi dengan nilai baku mutu yang berlaku, serta mengkaji karakteristik lumpur minyak sebagai bahan bakar alternatif. Pengambilan contoh uji dilakukan di salah satu industri semen yang telah memanfaatkan bahan bakar alternatif dengan mengacu pada  standar internasional EN 13284-1 dan  ISO 7934. Konsentrasi rata-rata TSP dan SO2 saat penggunaan batu bara masing-masing diperoleh sebesar 31,48 dan 19,67 mg/Nm3, sementara saat penggunaan batu bara dan lumpur minyak masing-masing adalah 19,60 dan 12,21 mg/Nm3. Kedua konsentrasi berada di bawah ambang batas baku mutu emisi masing-masing. Dari hasil beberapa penelitian, kandungan terbesar lumpur minyak berupa senyawa-senyawa organik terutama hidrokarbon. Kandungan abu dalam lumpur minyak berkisar 1,88-18,51% dan kandungan sulfur berkisar 2,06-2,26% dari total persen berat, sehingga emisi TSP dan SO2 yang dihasilkan relatif rendah.ABSTRACTCement industry needs lots of energy, which fulfilled by fossil fuel. Therefore, finding alternative energy should be encouraged. On the other side, there is a need to manage the waste as the result of industrial activities. One of the alternatives is co-processing, which is a process to recover the energy and waste for industrial production process. One of the waste that has been used is oil sludge. The purposes of this research were to compare the concentration of Total Suspended Particulate (TSP) and Sulfur dioxide (SO2) when they use coal only and coal which added by oil sludge, to compare the concentrations with the standard limit, also to characterize the oil sludge. Samples were taken at one of the cement industries that have used alternative fuel  according to international standard EN 13284-1 and ISO 7934. The average concentration of TSP and SO2 which only used coal were 31.48 and 19.67 mg/Nm3 respectively, while the TSP and SO2 concentration that used coal and oil sludge were 19.6 and 12.21 mg/Nm3, respectively. The concentration of TSP and SO2 were below the standard limit. The major content of oil sludge are organic compounds, especially hydrocarbon. In the oil sludge, ash content ranged between 1.88-18.51% and sulfur content ranged between 2.06-2.26% of the total weight, so the TSP and SO2 emissions may be produced in low concentration.
BIODEGRADASI RESIDU TOTAL PETROLEUM HIDROKARBON DI BAWAH KONSENTRASI 1% (W/W) HASIL PROSES BIOREMEDIASI (Biodegradation of Total Petroleum Hydrocarbons Residues below 1% Concentration (W/W) Using Bioremediation Process) Allen Kurniawan; Agus Jatnika Effendi
Jurnal Manusia dan Lingkungan Vol 21, No 3 (2014): November
Publisher : Pusat Studi Lingkungan Hidup Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/jml.18555

Abstract

ABSTRAKSektor pertambangan minyak bumi dan gas cenderung menghasilkan limbah yang dipersepsikan sebagai salah satu sumber pencemaran lingkungan. Menurut Keputusan Menteri Lingkungan Hidup Nomor 128/2003, proses bioremediasi merupakan teknologi alternatif untuk meminimalisasi dan memulihkan lahan tercemar dengan melibatkan aktivitas mikroorganisme hingga persyaratan konsentrasi akhir limbah minyak bumi berupa Total Petroleum Hydrocarbons (TPH) kurang dari 1%. Pemilihan mikroorganisme indigenous pada konsentrasi substrat kecil diharapkan menghasilkan nilai saturasi substrat terkecil sehingga tingkat afinitas tertinggi dapat diperoleh. Tujuan penelitian ini mencari dan mengidentifikasi isolat mikroorganisme petrofilik dari contoh uji hasil proses bioremediasi pada konsentrasi TPH 1%, menentukan nilai parameter kinetika biodegradasi, dan mengaplikasikan mikroorganisme terpilih pada proses bioremediasi tipe landfarming. Tahap isolasi dan identifikasi bakteri indigenous menghasilkan isolat bakteri Pseudomonas putida AK.A dan Pseudomonas diminuta AK.B. Penentuan kinetika biodegradasi dilakukan pada setiap jenis isolat dan kultur tercampur. Nilai laju pertumbuhan spesifik (µ), laju pertumbuhan spesifik maksimum (µmax), konsentrasi setengah jenuh (KS), koefisien produksi sintesis sel (Y), laju utilisasi substrat spesifik (q), laju utilisasi substrat spesifik maksimum (qmax), dan koefisien kematian indigenous (kd) pada P. putida AK.A. berturut-turut sebesar 0,0679-0,0788/jam; 0,078/jam; 0,0152%; 0,1011; 0,6716-0,7794/jam; 0,76/jam; 0,0085/jam; P. diminuta AK.B sebesar 0,0754-0,0874/jam; 0,0873/jam; 0,0182%; 0,1246; 0,7458-0,8645/jam; 0,701/jam; 0,0058/jam; dan kultur tercampur sebesar 0,0825-0,0948/jam 0,0945/jam; 0,016%; 0,2257; 0,8160-0,9377/jam; 0,419/jam; 0,0035/jam. Kultur tercampur digunakan pada reaktor landfarming skala laboratorium. Berdasarkan hasil penelitian, isolat bakteri Pseudomonas dalam kultur tercampur dapat menurunkan konsentrasi TPH di bawah 1%, dengan efisiensi sebesar 87,4% dalam jangka waktu satu bulan.ABSTRACTThe mining sector of oil and gas are likely to generate waste wbich is perceived as a source of environmental pollution. According to “Keputusan Menteri Lingkungan Hidup No. 128/2003” (Environmental Ministry Decree), the process of bioremediation is an alternative technology to minimize and recover land which polluted by microorganism activities until the final requirements of petroleum waste concentration is less than 1%. Indigenous microorganisms elected on small substrate concentrations are expected to get the smallest saturation value of the substrate so the highest affinity level can be obtained. The purpose of the research sought and identified petrofilic microorganisms isolated by bioremediation process resulted of 1% Total Petroleum Hydrocarbons concentration, determined the value of biodegradation kinetic parameters, and applied the microorganisms selected on bioremediation process of landfarming. The isolation and identification of indigenous bacteria process produced Pseudomonas putida AK.A and Pseudomonas diminuta AK.B. Determination of biodegradation kinetics was performed on each isolate and mixed culture. The value of specific growth rate (μ), maximum specific growth rate (μmax), the concentration of half saturation (KS), the synthesis of cell production coefficient (Y), specific substrate utilization rate (q), maximum specific substrate utilization rate (qmax), and endogenous decay coefficient (kd) for P. putida AK.A are 0.0679-0.0788/hour; 0.078/hour; 0.0152%; 0.1011; 0.6716-0.7794/hour; 0.76/hour; 0.0085/hour; P. diminuta AK.B are 0.0754-0.0874/hour; 0.0873/hour; 0.0182%; 0.1246; 0.7458-0.8645/hour; 0.701/hour; 0.0058/hour; meanwhile for mix culture are 0.0825-0.0948/hour; 0.0945/hour; 0.016%; 0.2257; 0.8160-0.9377/hour; 0.419/hour; 0.0035/hour. The mixed culture bacteria was used on landfarming reactor. Based on the results, isolates of Pseudomonas bacteria in mixed cultures can reduce TPH concentrations below 1% at landfarming reactor.