Article Per Year (5 Year)
p-Index From 2021 - 2026
1.518
P-Index
This Author published in this journals
All Journal Transmisi: Jurnal Ilmiah Teknik Elektro Media Teknika AL-JAZARI JURNAL ILMIAH TEKNIK MESIN TEKNOLOGI : Jurnal Ilmiah dan Teknologi Majamecha Jurnal Ilmiah Teknik Mesin Poros Automotive Experiences IRA Jurnal Teknik Mesin dan Aplikasinya (IRAJTMA) JESCEE- Journal of Emerging Supply Chain, Clean Energy, and Process Engineering International Journal of Mechanics, Energy Engineering and Applied Science (IJMEAS) Cylinder : Jurnal Ilmiah Teknik Mesin
Hadi Sutanto
Program Studi Magister Teknik Sistem Program Pascasarjana Fakultas Teknik Universitas Gadjah Mada Jalan Teknika Utara No.3 (Timur PAU UGM), Barek, Yogyakarta 55281
Aerospace Engineering Automotive Engineering Chemical Engineering, Chemistry & Bioengineering Civil Engineering, Building, Construction & Architecture Control & Systems Engineering Decision Sciences, Operations Research & Management Education Electrical & Electronics Engineering Energy Engineering Industrial & Manufacturing Engineering Materials Science & Nanotechnology Mathematics Mechanical Engineering Transportation

Published : 12 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 1 Documents
Search
Journal : media teknika

 1 
Analisis Tegangan Roda Gigi Miring pada Transmisi Kendaraan Roda Empat berdasarkan AGMA dan ANSYS Sutanto, Hadi
Media Teknika Vol 12, No 1 (2017)
Publisher : Sanata Dharma University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1549.212 KB) | DOI: 10.24071/mt.v12i1.943

Abstract

Two kinds of stresses in the gear teeth are root bending stress and tooth contact stress. These two stresses results in the failure of gear  teeth.  The root bending stress results in fatigue failure and contact stress results in pitting failure at the contact surface. The stress analysis used to minimize gear  failure in the  design of helical gear.  It is also optimize the  design of helical gear  on the transmission system of the truck motor vehicle, where the power transmission is required at heavy loads  with  smoother  and  noiseless operation.  In this  paper  bending  stress  and  contact  stress estimated  using analytical method while modeling of gears used the numerical solution. Method of beam strength  based on modified Lewis calculation used to predict the bending strength  of helical gears. Contact stress was estimated  using related method of AGMA contact stress. Stress modeling of helical gears is done by ANSYS 14.5, which is a finite element analysis package. The results are then compared with both AGMA and ANSYS procedures. The values of bending strength and contact stress determined using AGMA method found to be compatible with ANSYS simulation.
Co-Authors Ahmad Agus Setiawan Anthon de Fretes, Anthon de Fretes Archi Kun Cahyo Utomo Bachtiar, Marselinus Bachtiar, Marsellinus Basuki, Widodo Widjaja Budi Triyono Fathon'D, Ar Rasyid Ginting, Eliata Dumar Hafyyan, Iqbal Harianja, Valeska Harto Tanujaya Hudaya, Hoo Bram Natanael Istighfari, Nurrahman Kingkin, Diwangkoro Leman, Abdul Mutalib Marcellio, Ricco Novi Misgi Prabowo Adi Prakosa, Taji Harya Prasetyo, Dony Eko Rosehan Rosehan, Rosehan Sandra Octaviani setiawan, Dibyo Setiawan, Yosua Soewono, Arka Dwinanda Steven Darmawan, Steven Tarcisius Haryono, Tarcisius Tino Hermanto Umar, Siproni Wahju, Marsellinus Bachtiar Widiarto, Sandra Octaviani B. Widiyati, Khusnun Wijaya, Dikky Kusuma