Claim Missing Document
Check
Articles

Found 10 Documents
Search

Analisa Laju Korosi Pada Plat Baja ASME SA-283 Pada Daerah Splash Zone Reza Putra; Muhammad Muhammad; Abdul Rahman; M. Rifai Adithia
Jurnal Mekanova: Mekanikal, Inovasi dan Teknologi Vol 6, No 2 (2020): Oktober
Publisher : universitas teuku umar

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (636.077 KB) | DOI: 10.35308/jmkn.v6i2.2960

Abstract

Research on the corrosion rate of ASME SA-283 alloy steel has been carried out in the coastal environment. Corrosion is a decrease in the quality of the material that occurs due to the environment, where the coast is a splash zone area which is rich in salt content as a trigger for corrosion. Alloy steel is a material that is used widely as part of the construction of dock buildings on the coast The study was carried out by giving coating defects to ASME SA-283 material and varying the salinity in the splash zone area, where the coating thickness ranged from 350 μm - 410 μm and salt splash testing was carried out for 15 days. The results of the salt splash test show the types of corrosion that occur, namely pitting corrosion and unifrom corrosion. The largest corrosion rate occurred in the area that experienced a coating defect of 1,705 mm / year. The effect of coating on the corrosion rate is very large and the effect of coating defects on corrosion growth is quite high because the coating that functions as a protective specimen has been lost. The aim of this study are expected to become a reference for coating protection data in preventing corrosion growth in coastal environments. Keywords— Coating Defects, Corrosion Rate, Splash zone, Salinity.
PENGARUH FAKTOR LINGKUNGAN TERHADAP POTENSI KOROSI PADA PIPA AIR BAWAH TANAH DI JALUR KRUENG PEUSANGAN HINGGA KRUENG GEUKUEH, ACEH UTARA Reza Putra; Muhammad Muhammad; Syifaul Huzni; Syahrizal Fonna
FLYWHEEL : Jurnal Teknik Mesin Untirta Volume IV Nomor 1, April 2018
Publisher : Universitas Sultan Ageng Tirtayasa

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (723.679 KB) | DOI: 10.36055/fwl.v1i1.3289

Abstract

Dalam dunia industri  penggunaan jaringan pipa merupakan salah satu elemen yang memegang peranan penting yaitu sebagai rantai produksi. Kegagalan yang biasa terjadi pada struktur pipa baja yang ditanam di dalam tanah biasanya terjadi karena serangan korosi. Penelitian ini dilakukan untuk melakukan evaluasi terhadap pipa baja penyalur air baku dari Krueng Peusangan hingga Krueng Geukuh, Aceh Utara dengan melakukan pengukuran nilai potensial, resisitivitas tanah dan PH tanah. Pengukuran potensial menggunakan metode Half Cell dengan elektroda referensi Cu/CuSO4 yang dilakukan pada testbox yang tersedia dilapangan, resisitivitas menggunakan metode Wenner  dan pengukuran pH langsung dilokasi penelitian. Hasil penelitian menunjukkan  lokasi Desa Reuleut merupakan lokasi yang memiliki nilai potensial -915 mV dengan nilai resistivitas tanah terendah yaitu 442.65 pada lokasi persawahan sehingga dapat berpotensi korosi tingkat ekstrim dengan kadar pH asam. Hasil keseluruhan menunjukkan bahwa pipa bawah tanah terproteksi dari serangan korosi dengan kondisi lingkungan tanah yang bervarasi. Pada lokasi Desa Pinto Makmur yang juga merupakan daerah persawahan, dimana memiliki nilai potensial sebasar -973 mV dengan kadar pH 6.5, mengisyaratkan kondisi lingkungan ini membutuhkan perhatian khusus untuk mencegah terjadinya reaksi korosi pada pipa bawah tanah.
PEMETAAN POTENSI KOROSI PADA JALUR PIPA BAWAH TANAH MENGGUNAKAN INTERPOLASI KRIGING Reza Putra; Muhammad Muhammad; Syifaul Huzni; Nurdin Ali
Prosiding Semnastek PROSIDING SEMNASTEK 2017
Publisher : Universitas Muhammadiyah Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Telah dilakukan penelitian untuk memetakan potensi korosi pada jalur pipa bawah tanah menggunakan metoda interpolasi Kriging. Lokasi penelitian terletak di Aceh Utara hingga Bireun, dengan garis lintang 5°11' N dan 5°15' N, dan bujur 96°48' E dan 97°03' E. Pengukuran resistivitas tanah menggunakan metoda Wenner, dengan variasi jarak 150cm, 300cm dan 450cm. Hasil pengukuran ini diinterpolasi dengan metoda Kriging untuk memperoleh pemetaan. Hasil penelitian menunjukkan distribusi nilai resistivitas beragam dengan kontur yang bervariasi berdasarkan kedalaman pengukuran. Secara keseluruhan lokasi penelitian berpotensi korosi ringan, korosi menengah  dan korosi berat.
Uji Mekanik Komposit Berpenguat Serat Pandan Duri dan Resin Polyester Dengan Variasi Komposisi Metoda Fraksi Berat Muhammad Muhammad; Reza Putra
Jurnal Teknologi Kimia Unimal Vol 6, No 2 (2017): Journal Teknologi Kimia Unimal - Nopember 2017
Publisher : LPPM Universitas Malikussaleh

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/jtku.v6i2.476

Abstract

Tujuan dari penelitian ini adalah untuk memperoleh nilai kekuatan tarik optimaldari komposit berpenguat serat pandan duri dan resin polyester melaluiperbandingan variasi komposisi metoda fraksi berat. Proses pembuatan spesimen uji dengan bahan serat pandan duri dan resin polyester sesuai dengan standar uji tarik ASTM D3039. Variasi perbadingan fraksi berat untuk resin dan seratadalah 30% : 70% ; 40% : 60% dan 50% : 50%. Hasil penelitian menunjukkan nilai kekuatan tarik maksimal adalah pada perbadingan komposisi komposit 40%berat resin polyester dan 60 % berat serat pandan duri, yaitu 0.45 Kg.f/mm2 dengan nilai beban maksimum rata yang mampu ditahan sebesar 43.87 Kg.f. Darihasil penelitian ini dapat disimpulkan komposit berpenguat serat pandan duridengan resin polyester telah memenuhi nilai standar minimum untuk sebuahmaterial baru fibreboard berdasarkan ISO 17064:2010.
ANALISA RESISTIVITAS TANAH TERHADAP PREDIKSI KOROSI PADA PIPA DISTRIBUSI AIR BERSIH DI KAMPUS UNIMAL BUKIT INDAH Reza Putra; Muhammad Muhammad; Abdul Rahman; Teuku Hafli; Nurul Islami
Malikussaleh Journal of Mechanical Science Technology Vol 6, No 1 (2022): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v6i1.8314

Abstract

This study aims to predict corrosion in water distribution pipes at the Bukit Indah Unimal campus. Corrosion is the damage to chemical elements in a metal that changes the original properties of the metal. There are four kinds of processes for corrosion, namely, one anode loses electrons, two cathodes accept electrons, three liquids and four metals connect the cathode and anode. The geoelectric resistivity method is used to determine the soil resistance properties of the subsurface layer. The wenner 4 pin method is a geoelectric data retrieval that is often used with the same pin spacing arrangement. Res2Dinv is software that is on a computer to generate 2-dimensional images from the resistivity data obtained and determine the layer below the surface. From the inverse results, the smallest error value can be obtained when iterating up to 4 times, namely Java Road 45.3%, Sulawesi Road 49.6%, Kalimantan Road 30.6%, Sumatra II Road 46.1%, Main Gate 41.1% Sumatra I 23.4%. Based on the data, the measurable results below the surface range from 0.05 m to 5 m.
ANALISA PENGARUH PERBANDINGAN FRAKSI BERAT PARTIKEL KAYU SEMARAM DAN PENGIKAT RESIN POLYESTER TERHADAP SIFAT MEKANIK KOMPOSIT Muhammad Muhammad; Reza Putra; Asnawi Asnawi; Edy Yusuf; Muhammad Sayuti
Malikussaleh Journal of Mechanical Science Technology Vol 6, No 1 (2022): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v6i1.8315

Abstract

Tujuan dari penelitian ini adalah untuk mengetahui kekuatan bending yang paling optimal dari komposit serbuk kayu dengan variasi fraksi berat serbuk 10% Serbuk Kayu + 90% Resin BQTN 157, 20% serbuk kayu+80% resin BQTN 157 dan 30% serbuk kayu+70% Resin BQTN 157. Untuk Proses pembuatan spesimen uji dengan bahan serbuk kayu dan resin polyester sesuai dengan standar ASTM D790. Komposisi 10%:90% dengan hasil rata-rata 37,814 Kgf untuk beban maksimum dan 0,376 Kgf/mm² untuk kekuatan tekan. Nilai kerapatan tertinggi pada material berkomposisi 10% serbuk kayu semaram dan 90% resin adalah  1,193 gr/cm3. Sedangkan untuk komposisi 20% serbuk kayu semaram dan 80% resin hasil yang didapat 1,046 gr/cm3. Dan untuk komposisi 30% serbuk kayu semaram dan 70% resin hasil yang didapat 1,095 gr/cm3. Proses pencampuran yang terbaik terjadi pada specimen dengan komposisi 10% serbuk kayu dan 90% resin. Jenis patahan yang terjadi berupa getas
ANALISA PENGARUH HOLDING TIME DAN TEMPERATUR PADA PACK CARBURIZING MENGGUNAKAN LIMBAH KULIT SINGKONG TERHADAP SIFAT FISIK DAN MEKANIK BAJA 1020 Fikri, Ali; Muhammad, Muhammad; Rahman, Abdul; Putra, Reza; Habibi, Muhammad
Malikussaleh Journal of Mechanical Science and Technology Vol 7, No 2 (2023): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v7i2.13647

Abstract

The purpose of this study to determine the effect holding time on increasing the surface hardness of AISI 1020 steel material and analyzing the physical and mechanical properties of the results pack carburizing cassava peel waste on AISI 1020 steel. Process pack carburizing in this study have variations temperature 875oC and 900oC withholding time 60 minutes, 80 minutes, 100 minutes and 120 minutes. The catalyst used in this study was a carbonate compound, namely 20% BaCo3 to accelerate the reaction of adding carbon. The research results show that pack carburizing from cassava peel waste carbon can increase the surface hardness of AISI 1020 steel or part of the mechanical properties of the material. Testing at a temperature of 875oC withholding time 60 minutes which is 10.7 HRC and is the lowest value in the study while the highest hardness value occurs at a temperature of 900OC withholding time 120 minutes is 48.2 HRC. Microstructure observation results (metallography) on the edges indicates the martensite phase. The more martensite phase, the higher the value of the surface hardness of the steel material in the same direction as the effect of the length of holding time(holding time)
Pengaruh Arah Serat Pada Lamina Komposit Berpenguat Serat Bambu Terhadap Kekuatan Tarik mumfazir, mumfazir; Nayan, Ahmad; Muhammad, Muhammad; Suryadi, Suryadi
Malikussaleh Journal of Mechanical Science and Technology Vol 8, No 2 (2024): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v8i2.17923

Abstract

Penelitian ini bertujuan untuk mengetahui pengaruh variasi ketebalan core PE foam terhadap kekuatan bending komposit sandwich serat bambu apus menggunakan resin epoxy. Pembuatan komposit sandwich dilakukan dengan metode Hand Lay Up. Pengujian uji bending dilakukan berdasarkan standar         (ASTM C 393). Hasil penelitian ini dari 3 variasi ketebalan core PE foam 20, 30 dan 40 mm tersebut yang memiliki kekuatan bending tertinggi pada ketebalan core PE foam 20 mm dengan nilai rata-rata sebesar 1,78 MPa, sedangkan nilai kekuatan bending terendah terdapat pada ketebalan core PE foam 40 mm dengan nilai rata-rata sebesar 0,89 MPa. Dapat disimpulkan bahwa dengan bertambahnya core PE foam maka kekuatan bendingnnya akan menurun, sedangkan core yang tidak tebal akan berbanding terbalik. Skin bagian atas akan rusak terlebih dahulu oleh beban tekan, sedangkan skin bagian bawah akan rusak oleh beban tarik komposit sandwich. Untuk Jenis patahan dari komposit sandwich serat bambu apus  dengan variasi ketebalan core PE foam 20, 30 dan 40 mm menggunakan resin epoxy mengalami jenis patahan pada spesimen ialah patahan face yield dan debonding.
Analisis Uji Tarik dan Bending Komposit Hybrid Serat Nanas dan Glasswool Dengan Matriks Polyester Hidayat, Rizki; Muhammad, Muhammad; Islami, Nurul; Putra, Reza; Rahman, Abdul
Malikussaleh Journal of Mechanical Science and Technology Vol 8, No 2 (2024): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v8i2.17436

Abstract

Salah satu serat yang dapat dimaanfaatkan sebagai bahan pengisi pada produk komposit yaitu serat nanas dan glasswool yang sangat mudah didapatkan serta ramah lingkugan. Tujuan penelitian ini adalah untuk menganalisis kekuatan tarik dan bending yang teringgi pada setiap variasinya. Spesimen uji dibuat menggunakan metode hand lay up dengan pengujian tarik menggunakan ASTM D638-02 dan bending ASTM D90. Hasil pengujian kekuatan tarik yang paling optimal terdapat pada fraksi volume (SN 40% : GW 20% ) dengan nilai rata-rata sebesar  = 37,11 MPa untuk kekuatan luluh sebesar 29,87 MPa dan regangan tarik sebesar  6,49 % pada variasi (SN 30% : 30% GW) nilai rata-rata sebesar  = 24,48 MPa untuk kekuatan luluh sebesar 18,38 MPa dan regangan sebesar  6,74%, variasi (SN 10% : GW 50%) rata-rata kekuatan tarik sebesar  =17,05 MPa dengan kekuatan luluh sebesar 13,89 MPa dan regangan meningkat sebesar  829%. Hasil pengujian bending tertinggi terdapat pada variasi (SN 40% : GW 20%) dengan rata-rata kekuatan bending sebesar 115,79 MPa untuk kekuatan luluh didapatkan sebesar 5,23 MPa untuk variasi (SN 30% :GW 30%) didapatkan kekuatan bending sebesar 90,19 MPa dengan kekuatan luluh 5,23 MPa dan variasi (SN 10% : 50% GW ) didapatkan kekuatan bending sebesar 68,13 MPa dengan kekuatan luluh 3,11 MPa. Pencampuran yang terbaik terjadi pada spesimen dengan komposisi 40% serat nanas dan 20% glasswool. Jenis patahan yang terjadi berupa getas.
Pengaruh Minyak Nabati Sebagai Pendingin Terhadap Temperatur dan Kekasaran Permukaan Baja ST 42 pada Proses Pembubutan Rangkuti, Mhd. Saleh; Aljufri, Aljufri; Rizki, Muhammad Nuzan; Rahman, Abdul; Muhammad, Muhammad
Malikussaleh Journal of Mechanical Science and Technology Vol 8, No 2 (2024): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v8i2.17669

Abstract

In the machining process, selecting the appropriate tool and coolant significantly affects the surface roughness of a product to be manufactured. The purpose of this research is to compare between soluble oil and vegetable oil as coolants in reducing roughness values and dissipating heat generated during the machining process of ST 42 steel. Carbide tools and vegetable oil coolants, namely cooking oil and castor oil, are used in this study, with soluble oil used as a reference. The machining process in this study employs conventional machining with a spindle speed of 1200 rpm, a cutting depth of 0.2 mm and 0.4 mm, and a cutting speed of 0.04 mm/minute. Temperature data collection during the machining process is carried out using a thermogun, and surface roughness testing is conducted using a Mitutoyo SJ-310 surface roughness tester. From the test results, the lowest roughness and temperature values are obtained at a cutting depth of 0.2 mm for all types of coolants used. The use of soluble oil yields the lowest average roughness and temperature values, which are 35.2 °C and 0.9 µm, respectively. Meanwhile, in the use of vegetable oil to minimize surface roughness, the lowest average value is found in cooking oil, which is 1.5 µm, and to minimize surface temperature during machining, castor oil coolant is the most effective, with a temperature of 40.1 °C.