Article Per Year (5 Year)
p-Index From 2021 - 2026
1.037
P-Index
This Author published in this journals
All Journal Journal of Mechanical Engineering Science and Technology Journal of Mechanical and Electrical Technology JES-TM Social and Community Service Automotive Innovations Journal
Faqih Fadillah
Unknown Affiliation
Automotive Engineering Computer Science & IT Control & Systems Engineering Decision Sciences, Operations Research & Management Education Electrical & Electronics Engineering Energy Engineering Industrial & Manufacturing Engineering Materials Science & Nanotechnology Mechanical Engineering Other

Published : 5 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 5 Documents
Search

 1 
Effect of Addition Titanium Dioxide Nanoparticle on Properties of Pineapple Leaf Fiber Mediated TEMPO Oxidation Oxidation Ramadhan, Rahmad Ikrom; Suryanto, Heru; Fikri, Ahmad Atif; Aminnudin, Aminnudin; Maulana, Jibril; Fadillah, Faqih; Mito, Mohamed T; Masera, Kemal
Journal of Mechanical Engineering Science and Technology (JMEST) Vol 8, No 1 (2024)
Publisher : Universitas Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17977/um0168i12024p082

Abstract

Indonesia is an agricultural country with the potential to grow many plants as natural fiber sources. In order to improve its properties, natural fiber needs to be treated by applying nanomaterial so that it can compete with the characteristics of synthetic fibers. The study aims to determine the influence of adding titanium dioxide (TiO2) nanoparticles on pineapple leaf fiber (PALF) characteristics. The PALF was collected from the Subang plantation (Indonesia). The chemical treatment was carried out with pre-treatment using an alkalization process for 3 hours, and the oxidation process was carried out with TEMPO. TiO2 nanoparticle grafting was carried out by adding a silane solution with a ratio of 1:10 with alcohol. The characteristics of PALF were observed using XRD, FTIR, SEM, and tensile tests. The results show that the crystallinity of the PALF increased after TEMPO treatment. PALF form Si-O-C bond identified at a wavelength of 1158 cm-1 after silane treatment. Ti – O – Si functional groups were identified in the 660 cm-1 – 670 cm-1 wavelength range. In the fiber surface, agglomerated TiO2 nanoparticles are formed and increase with increasing TiO2 nanoparticle concentration. The tensile stress of treated PALF is increased by 125%, with the highest tensile strength of 1279.18 MPa, obtained by TiO2 nanoparticle concentration of 1.0%.
Study on Effect of 3D Printing Parameters on Surface Roughness and Tensile Strength Using Analysis of Variance Fadillah, Faqih; Suryanto, Heru; Suprayitno, Suprayitno
Journal of Mechanical Engineering Science and Technology (JMEST) Vol 7, No 2 (2023)
Publisher : Universitas Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17977/um016v7i22023p096

Abstract

Fused deposition modeling of 3D printing is the process of making workpieces or parts by adding filaments to each layer. Some indicators of a high-quality product of 3D printing are the precisions dimensions, the surface roughness, and tensile strength. This research aims to find the parameters most affecting surface roughness and tensile strength. The research design used an experimental method with input parameters: (1) print speed (15-35 mm/s), (2) print temperature (200-210°C), (3) layer height (0.1 – 0.3 mm), (4) infill line directions (0-90°), and dependent variables were surface roughness and tensile strength. The data distribution used the L9 orthogonal array, and the statistic analysis used ANOVA. Material uses nanographite-reinforced polylactic acid (PLA) filament. The results indicate that print parameters that significantly affect surface roughness are layer height and infill line directions. The best surface roughness on the layer height parameter is 0.1 mm, and the infill line directions parameter is 90°. Based on ANOVA analysis, print speed, print temperature, and layer height do not significantly affect tensile strength, but infill line directions significantly affect tensile strength. The best tensile strength on infill line directions is 90°. The best average tensile strength with nanographite-reinforced PLA filament is 38.56 N/mm2, with 35 m/s print speed, 205 °C print temperature, 0.1 mm layer height, and 90° infill line direction parameter. The best average surface roughness with nanographite-reinforced PLA filament is 0.66 µm, with 35 m/s print speed, 205 °C print temperature, 0.1 mm layer height, and 90° infill line direction parameter.
Analisis Retak Pada Blade Impeller Dengan Pendekatan Static Structure Priyasudana, Danang; Fadillah, Faqih
Automotive Innovations Journal Vol. 1 No. 2 (2025): September
Publisher : Department of Automotive Engineering Technolgy

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Impeller merupakan komponen pompa yang memiliki peran yang sangat penting pada pompa. Desain impeller yang efisien sangat penting dan berguna untuk merancang suatu pompa . Banyak faktor yang berpengaruh terhadap desain impeler seperti sudut masuk dan sudut keluar impeler serta desain dan jumlah blade dari impeller, jika didesain dan diteliti secara eksperimental akan membutuhkan waktu yang lama dan biaya yang mahal. Oleh karena itu perlu, dilakukan simulasi untuk mengetahui kekuatan material blade impeller menggunakan ANSYS dengan pendekatan static structure, meliputi stress analysis, total deformation, dan stress intensity factor (SIF) pada blade impeller yang berbahan aluminium untuk manganalisis retak tang terjadi.Hasil simulasi menunjukkan Stress Analysis menggunakan pendekatan Von Misses menunjukkan tegangan maksimum sebesar 59661 MPa dan tegangan minimum sebesar 30.913 MPa. Selanjutnya total deformation pada blade impeller menunjukkan bahwa nilai maksimum sebesar 16.287 MPa dan minimum sebesar 0 MPa. Lokasi nilai maksimum merupakan daerah dengan potensi mengalami patah atau retak paling tinggi. Dan untuk Stress Intensity Factor (SIF) maksimum Mode II sebesar dan Mode III sebesar .
Implementation of a CNC E-Module Integrating Pancasila Values at Angkasa Aviation Vocational High School, Malang Fadillah, Faqih; Zakka Agustin, Rizkika; Rizky Septiawan, Diama; Dwi Putra, Agus
Journal of Social and Community Service Vol. 4 No. 3 (2025): November 2025
Publisher : Faculty of Engineering University of Pahlawan Tuanku Tambusai

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31004/jestmc.v4i3.374

Abstract

The high unemployment rate among Vocational High School (SMK) graduates indicates a gap between graduates’ competencies and labor market demands, particularly in machining engineering. Vocational education also tends to emphasize technical skills without sufficient reinforcement of character and moral values. This community service activity aims to implement a Computer Numerical Control (CNC) e-module integrated with Pancasila values to enhance technical competencies while fostering students’ character development. The methods include needs analysis, e-module design, learning implementation, and evaluation. The analysis of pretest and posttest results shows a significant improvement, demonstrating the effectiveness of the e-module in improving CNC competencies and internalizing Pancasila values.
Studi Eksperimental Pengaruh pH Pendingin Mesin terhadap Suhu Kerja dan Emisi Gas Buang pada Motor 4 Silinder Septiawan, Diama Rizky; Wijoyo, Wijoyo; Putra, Agus Dwi; Surjadi, Eko; Fadillah, Faqih
Metrotech (Journal of Mechanical and Electrical Technology) Vol 5 No 1: Januari 2026
Publisher : Fakultas Sains dan Teknologi, UNIRA Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.70609/metrotech.v5i1.8263

Abstract

Tujuan dari penelitian ini adalah untuk memperoleh pendingin yang mampu menahan suhu operasi mesin lebih lama (suhu operasi mesin rendah) dan mengurangi emisi mesin. Pendingin radiator adalah pendingin yang biasanya digunakan pada radiator. Komponen ini berfungsi untuk mengontrol suhu di dalam mesin kendaraan agar tidak berlebihan karena dapat menyebabkan mesin panas berlebih dan merusak mesin mobil. Penggunaan air biasa atau air mineral tidak dapat memaksimalkan kinerja pendingin dalam mendinginkan mesin. Dalam penelitian ini metode yang digunakan adalah metode eksperimental untuk menguji apakah variabel eksperimen efektif atau tidak. Variabel Independen, variasi jenis cairan pendingin, Variabel Dependen, suhu kerja mesin dan emisi knalpot, Variabel Kontrol, suhu ruangan saat pengumpulan data. Hasil penelitian menunjukkan bahwa suhu kerja tertinggi diperoleh dengan menggunakan air suling dengan tingkat keasaman (pH) 6,32, yaitu 89,5 oC dan suhu kerja mesin terendah. Hasil menunjukkan bahwa suhu kerja tertinggi diperoleh dengan menggunakan air suling dengan tingkat keasaman (pH) 6,32, yaitu 89,5 oC, dan suhu kerja mesin terendah adalah dengan menggunakan cairan pendingin jenis Water coolant (pH 8,04) 85 oC. Penggunaan Water coolant (pH 8,04) sebagai cairan pendingin dapat mengurangi emisi gas buang CO sebesar 0,13%, HC sebesar 6,8 ppm, dan NOx sebesar 3,1 ppm. Kesimpulan yang diperoleh adalah bahwa suhu kerja mesin terendah diperoleh dengan menggunakan cairan pendingin jenis Water coolant dan dapat mengurangi emisi gas buang CO, HC, dan NOx.
Co-Authors Ahmad Atif Fikri Aminnudin, Aminnudin Diama Rizky Septiawan Eko Surjadi Heru Suryanto Jibril Maulana Masera, Kemal Mito, Mohamed T PRIYASUDANA, DANANG Putra, Agus Dwi Ramadhan, Rahmad Ikrom Rizky Septiawan, Diama Suprayitno Suprayitno Wijoyo Wijoyo Zakka Agustin, Rizkika