cover
Contact Name
Abd Kholiq
Contact Email
kholiq@unesa.ac.id
Phone
+6285731570404
Journal Mail Official
jifi@unesa.ac.id
Editorial Address
Jurusan Fisika FMIPA Universitas Negeri Surabaya Kampus Ketintang Unesa, Gedung C3 Lantai 1 Jl Ketintang, Surabaya 60321, Indonesia
Location
Kota surabaya,
Jawa timur
INDONESIA
Inovasi Fisika Indonesia (IFI)
ISSN : 23024216     EISSN : 28301765     DOI : https://doi.org/10.26740/ifi
Jurnal Inovasi Fisika Indonesia(IFI) is a peer-reviewed journal, ISSN: 2302-4216, which is managed and published by the Department of Physics, Faculty of Mathematics and Natural Sciences (FMIPA) Universitas Negeri Surabaya (UNESA). This journal is accessible to all readers and covers developments and research in physics (Materials Physics, Earth Physics and Instrumentation Physics).
Articles 431 Documents
PENGARUH PENAMBAHAN Bi2O3 TERHADAP PENURUNAN FRAKSI BERAT DAN PARAMETER KISI FASA SEKUNDER Mg2TiO4 PADA KERAMIK (Mg0,7Zn0,3)TiO3 firda dwi pangestuti; Frida U. Ermawati
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p326-333

Abstract

Abstrak Keramik MgTiO3 merupakan material dielektrik yang berpotensi dalam aplikasi telekomunikasi gelombang mikro. Untuk meningkatkan sifat material dielektrik, dilakukan doping menggunakan ion dan liquid additive agent (LAA). Makalah ini melaporkan pengaruh penambahan bahan LAA berupa Bi₂O₃ terhadap penurunan fraksi berat dan parameter kisi fasa sekunder Mg₂TiO₄ pada keramik (Mg₀,₇Zn₀,₃)TiO₃ (disingkat MZT03) dengan dan tanpa Bi2O3 berdasarkan XRD. Serbuk MZT03 disintesis dengan metode pencampuran larutan, dikalsinasi pada 500  selama 4 jam. 4 %wt. Bi2O3 ditambahkan melalui ball milling. Sebagai pembanding, sebagian serbuk kristalin MZT03 tidak ditambahkan 4 %wt. Bi2O3. Kedua macam serbuk tersebut dikompaksi pada tekanan 9 MPa sehingga menghasilkan pelet. Kedua pelet disinter pada 1100  selama 4 jam untuk menghasilkan kedua keramik uji. Data struktur menunjukkan MgTiO₃ merupakan fasa utama pada kedua keramik serta Mg2TiO4 sebagai fasa sekunder, dengan %berat fasa Mg2TiO4 turun dari 11,55 % (tanpa Bi2O3) menjadi 5,02 % (dengan Bi2O3), hasil sebaliknya untuk fasa MgTiO3. Fakta tersebut menunjukkan bahwa Bi₂O₃ efektif menekan pembentukan fasa Mg2TiO4. Tidak hanya itu, Bi2O3 juga mampu menurunkan ukuran parameter kisi fasa Mg2TiO4, parameter a=b=c sebesar 7,542  10-2 nm (tanpa Bi2O3) turun menjadi 7,435  10-2 nm (dengan Bi2O3) penurunan ukuran parameter kisi menyebabkan turunnya volume sel satuan. Uji densitas bulk meningkat dari 3,2 g.cm-3 (tanpa Bi₂O₃) menjadi 3,7 g.cm-3 (dengan Bi₂O₃) yang mengindikasikan bahwa penambahan Bi2O3 dapat meningkatkan densifikasi keramik. Berdasarkan hasil uji dilatometri, keramik tanpa Bi₂O₃ mengalami penyusutan sebesar 14,17 % pada 1300 °C, sedangkan dengan Bi₂O₃ mencapai 18,05 % pada suhu yang lebih rendah yakni 1080 °C.   Abstract MgTiO3 ceramics are dielectric materials with great potential for microwave telecommunication applications. To improve dielectric properties, doping was carried out using ions and liquid additive agent (LAA). This study reports effect of adding Bi2O3 as LAA on reduction of weight fraction and lattice parameters of the secondary phase Mg2TiO4 in (Mg0.7Zn0.3)TiO3 ceramics (abbreviated as MZT03) with and without Bi2O3 based on structures analysis. MZT03 powder was synthesized using solution-mixing method and calcined at 500 °C for 4 hours. 4 % wt. Bi2O3 addition was introduced by ball milling, while part of the crystalline MZT03 powder without Bi₂O₃ served as comparison. Both powders were compacted under pressure of 9 MPa become pellets, which were then sintered at 1100 °C for 4 hours to obtain ceramic samples. Structural analysis revealed MgTiO₃ was main phase in both ceramics, while Mg₂TiO₄ appeared as secondary phase. The weight fraction of Mg₂TiO₄ decreased from 11.55 % (without Bi₂O₃) to 5.02 % (with Bi₂O₃), whereas the MgTiO₃ phase showed the opposite trend. This indicates Bi₂O₃ effectively suppresses the formation of the Mg₂TiO₄ phase. Furthermore, Bi₂O₃ reduced lattice parameter of Mg₂TiO₄ phase from a=b=c = 7.542 × 10⁻² nm (without Bi₂O₃) to 7.435 × 10-2 nm (with Bi₂O₃), leading to smaller unit cell volume. Bulk density increased from 3.2 g·cm⁻³ to 3.7 g·cm-3, indicating improved densification. Dilatometric analysis showed that shrinkage increased from 14.17% at 1300 °C to 18.05 % at lower temperature of 1080 °C, confirming that Bi₂O₃ lowers sintering temperature through liquid-phase formation that enhances densification.
FORMULASI DAN EVALUASI PASTA GIGI HERBAL BERBASIS EKSTRAK DAUN PEPPERMINT (Mentha piperita L) DAN EKSTRAK DAUN SIRIH MERAH (Piper crocatum) : Kata Kunci : Formulasi, Pasta Gigi Herbal, Daun Sirih Merah, Daun Mint Qurry Mahdania; Pratiwi; Fitriana; Lydia Rohmawati
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p334-339

Abstract

Abstrak Salah satu masalah pada kesehatan gigi yang paling umum dialami oleh masyarakat di seluruh dunia adalah karies gigi atau kerusakan gigi. Karies gigi muncul akibar proses demineralisasi jaringan gigi yang dipicu oleh bakteri penyebab karies, seperti Streptococcus mutans. Pencegahan karies gigi dapat dilakukan dengan penggunaan pasta gigi yang dioleskan dan digosokkan pada permukaan gigi. Agar penyikatan gigi lebih efektif, diperlukan penggunaan pasta gigi yang mengandung bahan antibakteri. Daun peppermint (Mentha piperita L.) dan daun sirih merah (Piper crocatum) merupakan bahan alami yang telah terbukti mampu menghambat pertumbuhan Streptococcus mutans. Penelitian ini bertujuan untuk mengetahui perbandingan efektivitas formulasi pasta gigi ekstrak daun mint (Mentha piperita L.) dan ekstrak daun sirih merah (Piper crocatum). Sediaan pasta gigi ekstrak daun mint dan daun sirih merah dibuat dengan 4 formula (F1, F2, F3, dan F4). Pengujan mutu fisik kimia sediaan pasta gigi ekstrak daun mint dan daun sirih merah dilakukan uji organoleptik, uji homogenitas, dan uji pH. Berdasarkan hasil yang diperoleh, formulasi pasta gigi yang menunjukkan efektivitas terbaik adalah formula F1 (tanpa penambahan ekstrak) dan F2 (dengan ekstrak daun mint).   Abstract One of the most common dental health problems experienced by people around the world is dental caries or tooth decay. Dental caries occurs due to the demineralization process of tooth tissue triggered by caries-causing bacteria, such as Streptococcus mutans. Dental caries prevention can be done by using toothpaste that is applied and rubbed on the surface of the teeth. In order for brushing to be more effective, it is necessary to use toothpaste containing antibacterial ingredients. Peppermint leaves (Mentha sp.) and red betel leaves (Piper crocatum) are natural ingredients that have been proven to inhibit the growth of Streptococcus mutans. This study aims to determine the comparison of the effectiveness of the formulation of toothpaste with mint leaf extract (Mentha sp.) and red betel leaf extract (Piper crocatum). Mint leaf and red betel leaf extract toothpaste preparations are made with 4 formulas (F1, F2, F3, and F4). Testing the physical and chemical quality of toothpaste preparations containing mint leaf extract and red betel leaf extract was carried out through organoleptic tests, homogeneity tests, and pH tests. Based on the results obtained, the toothpaste formulations that showed the best effectiveness were formulas F1 (without the addition of extract) and F2 (with mint leaf extract).
PENGARUH PENAMBAHAN REDUCE GRAPHENE OXIDE (RGO) DALAM KOMPOSIT FE3O4/RGO SEBAGAI PENYERAP GELOMBANG RADAR DALAM RENTANG X-BAND Triya_Susila_Dewi; Diah Hari Kusumawati; Fitriana; Yana Taryana
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p361-368

Abstract

Abstrak Radar berfungsi untuk mendeteksi dan melacak objek, namun keberhasilan deteksi tersebut juga menghadirkan resiko sehingga diperlukan material penyerap gelombang radar (Radar Absorbing Material/RAM) yang efektif guna meningkatkan kemampuan siluman (stealth). Komposit Fe₃O₄/rGO, yang mengkombinasikan sifat magnetik dan dielektrik, memiliki potensi besar sebagai RAM. Pada penelitian ini, Fe₃O₄ disintesis dari pasir besi menggunakan metode kopresipitasi, sedangkan arang tempurung kelapa diolah menjadi reduced graphene oxide (rGO) melalui metode Hummers termodifikasi. Penelitian ini mengevaluasi pengaruh variasi massa rGO sebesar 0,07 gram hingga 0,11 gram dalam komposit Fe₃O₄/rGO pada rentang frekuensi X-band. Hasil karakterisasi Raman pada rGO menunjukkan rasio ID/IG sebesar 0,99, menandakan keberhasilan reduksi. Analisis XRD mengonfirmasi bahwa struktur fasa rGO, Fe₃O₄, serta komposit Fe₃O₄/rGO menunjukkan bahwa hasil puncak-puncak kristal tersebut sesuai dengan bidang kristal dari sampel rGO, Fe₃O₄, serta komposit Fe₃O₄/rGO. Uji penyerapan gelombang radar menunjukkan bahwa penambahan rGO berpengaruh terhadap peningkatan kemampuan penyerapannya. Reflection loss (RL) meningkat dari -8,98 dB hingga -11,07 dB seiring penambahan rGO, dengan nilai optimum diperoleh pada penambahan 0,10g rGO pada frekuensi 10,3 GHz dengan persentase absorpsi sebesar 92,17% (RL < -10 dB). Hasil ini menunjukkan bahwa peningkatan kandungan rGO dalam komposit Fe₃O₄/rGO mampu memperbaiki performa material sebagai RAM pada rentang frekuensi X-band.   Abstract Radar functions to detect and track objects; however, successful detection also poses risks, making it necessary to develop effective radar absorbing materials (RAM) to enhance stealth capabilities. The Fe₃O₄/rGO composite, which combines magnetic and dielectric properties, has great potential as a RAM. In this study, Fe₃O₄ was synthesized from iron sand using the coprecipitation method, while coconut shell charcoal was processed into reduced graphene oxide (rGO) through a modified Hummers method. This research evaluates the effect of varying rGO mass from 0.07 to 0.11 grams in the Fe₃O₄/rGO composite within the X-band frequency range. Raman characterization of rGO showed an ID/IG ratio of 0.99, indicating successful reduction. XRD analysis confirmed that the crystal phase structures of rGO, Fe₃O₄, and the Fe₃O₄/rGO composite corresponded well to the crystalline planes of the respective samples. Radar wave absorption testing demonstrated that the addition of rGO influenced an increase in absorption capability. Reflection loss (RL) improved from -8.98 dB to -11.07 dB with increasing rGO content, with the optimum value obtained at 0.10 g rGO at 10.3 GHz frequency exhibiting an absorption percentage of 92.17% (RL < -10 dB). These results indicate that increasing the rGO content in the Fe₃O₄/rGO composite can enhance the material's performance as a RAM in the X-band frequency range.
ANALISIS PENGARUH VARIASI PANJANG KOPLING TERHADAP EFISIENSI TRANSFER CAHAYA PADA SENSOR FIBER OPTIK DIRECTIONAL COUPLER Waluyo, Febbrya Eka Dewi; Muhimmatul Khoiro; Dzulkiflih
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p349-360

Abstract

Abstrak Industri air minum dalam kemasan yang berkembang pesat memicu peningkatan permintaan akan kualitas air yang lebih baik. Namun, kontaminasi logam berat, terutama kadmium (Cd²⁺), berisiko membahayakan kesehatan manusia. Kadmium dapat merusak organ dan sistem tubuh, sehingga diperlukan metode deteksi yang efisien dan sensitif. Penelitian ini bertujuan mengembangkan sensor fiber optik berbasis Directional Coupler untuk mendeteksi kadmium dalam air minum. Sistem deteksi menggunakan Laser BF4R (660 nm) sebagai pemancar cahaya dan Sensor BF5R sebagai penerima. Variabel penelitian meliputi suhu larutan (25±0,5°C), panjang coupling (2,8 cm, 2,9 cm, dan 3,0 cm), konsentrasi larutan Cd (0,05 ppm, 0,10 ppm, dan 0,15 ppm), serta variasi konfigurasi nyala laser (ON-OFF, OFF-ON, ON-ON). Kalibrasi dilakukan dengan memeriksa perbandingan antara fiber optik dengan cladding dan tanpa core, memastikan kedua core fiber optik menempel dengan tepat. Teknik pengambilan data dilakukan dengan mengukur intensitas cahaya yang terkopel pada fiber optik. Hasil penelitian menunjukkan panjang coupling 3,0 cm memberikan intensitas output tertinggi pada konfigurasi laser ON-OFF, dengan sensitivitas yang optimal untuk deteksi kadmium. Pembahasan menunjukkan bahwa panjang coupling yang lebih besar meningkatkan perpindahan cahaya antar fiber, dengan mode ganjil memperkuat gelombang evanescent yang meningkatkan efisiensi transfer energi. Penelitian ini membuktikan bahwa metode Directional Coupler pada fiber optik dapat diterapkan secara efisien untuk deteksi logam berat dalam air secara real-time dan dengan biaya rendah.   Abstract The rapidly growing bottled drinking water industry has led to increased demand for higher water quality. However, contamination by heavy metals, particularly cadmium (Cd²⁺), poses significant health risks. Cadmium can damage organs and body systems, necessitating efficient and sensitive detection methods. This study aims to develop an optical fiber sensor based on the Directional Coupler method for detecting cadmium in drinking water. The detection system employs a BF4R laser (660 nm) as the light emitter and a BF5R sensor as the receiver. Research variables include solution temperature (25±0.5°C), coupling lengths (2.8 cm, 2.9 cm, and 3.0 cm), cadmium solution concentrations (0.05 ppm, 0.10 ppm, and 0.15 ppm), and laser activation configurations (ON-OFF, OFF-ON, ON-ON). Calibration was performed by comparing fiber optics with and without cladding, ensuring the precise alignment of the cores. Data collection was done by measuring the coupled light intensity on the optical fibers. Results showed that a coupling length of 3.0 cm provided the highest output intensity in the ON-OFF laser configuration, demonstrating optimal sensitivity for cadmium detection. The discussion revealed that longer coupling lengths enhance light transfer between fibers, with the odd mode strengthening the evanescent wave, thus increasing energy transfer efficiency. This research demonstrates that the Directional Coupler method in optical fibers can effectively detect heavy metals in water in real-time and at a low cost.
ANALISIS XRD DAN EDX TERHADAP KEBERADAAN FASA-FASA PADA KERAMIK (Mg0,8Zn0,2)TiO3 DENGAN DAN TANPA PENAMBAHAN V2O5 Maulidiya Fadilatul Latifa; Frida Ulfah Ermawati
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p340-348

Abstract

Abstrak Keramik dielektrik merupakan material penting untuk aplikasi telekomunikasi pada gelombang mikro. MgTiO3 menjadi salah satu material dielektrik yang berpotensi untuk aplikasi tersebut. Agar mendapatkan sifat material yang lebih baik dibandingkan dengan sifat material aslinya, maka salah satu cara yang dapat dilakukan ketika fabrikasi keramik dielektrik adalah dengan menambahkan dopan berupa ion atau liquid additive agent (LAA) yang memenuhi syarat tertentu. Makalah ini bertujuan untuk melaporkan analisis pembentukan fasa-fasa yang terbentuk pada keramik (Mg0,8Zn0,2)TiO3 (disingkat MZT02) dengan dan tanpa penambahan 4 %wt. V2O5 sebagai LAA berdasarkan uji XRD dan EDX. Serbuk MZT02 disintesis dengan metode liquid mixing, dikalsinasi pada suhu 500 °C selama 5 jam. Sebagian serbuk kristalin MZT02 ditambah 4 %wt. V2O5 menggunakan planetary ballmill. Serbuk kristalin dengan dan tanpa V2O5 dikompaksi secara konvensional pada tekanan 8 MPa selama 10 detik menjadi pelet silinder pejal berdiameter 8 mm. Sinter dilakukan pada suhu 1100 °C selama 4 jam sebelum dikarakterisasi. Analisis XRD menunjukkan fasa utama MgTiO3 disertai dengan fasa intermediat Mg2TiO4 pada kedua keramik uji tersebut. Pada keramik MZT02+V2O5, %molar fasa MgTiO3 meningkat sedangkan fasa Mg2TiO4 turun dibandingkan dengan %molar pada keramik MZT02. Data parameter kisi dan volume sel satuan naik pada keramik MZT02+V2O5. Analisis EDX mendeteksi unsur-unsur bahan awal  yang digunakan yaitu Mg, Ti, Zn, dan O pada kedua keramik uji dengan rasio mendekati rasio unsur-unsur pada fasa MgTiO3 dan Mg2TiO4. Dengan demikian, analisis fasa-fasa pada keramik uji berdasarkan uji XRD dan EDX saling mendukung satu sama lain.   Abstract Dielectric ceramics are important materials for telecommunication applications in microwaves. MgTiO3 is one of the dielectric materials that has the potential for these applications. In order to obtain better material properties compared to the original material properties, one method that can be done when fabricating dielectric ceramics is by adding dopants in the form of ions or liquid additive agents (LAA) that meet certain requirements. This study focused on analyzing the phase formation in (Mg0.8Zn0.2)TiO3 ceramics (referred to as MZT02) both without and with the addition of 4 wt.% V2O5 as a LAA based on XRD and EDX tests. MZT02 powder was synthesized by the liquid mixing method, calcined at 500 °C for 5 hours. Part of the crystalline MZT02 powder was added with 4 wt.% V2O5 using a planetary ball mill. Crystalline powders with and without V2O5 were conventionally compacted at 8 MPa for 10 seconds into 8 mm solid cylindrical pellets. Prior to characterization, the pellets were sintered at 1100 °C for 4h. XRD confirmed that MgTiO3 was the primary phase, with Mg2TiO4 appearing as a secondary phase in both ceramic samples. In MZT02+V2O5 ceramics, the molar % of MgTiO3 phase increased while the molar % of Mg2TiO4 phase decreased compared to the molar % of MZT02 ceramics. Lattice parameter data and unit cell volume increased in MZT02+V2O5 ceramics. EDX analysis detected the elements of the starting materials used, namely Mg, Ti, Zn, and O in both test ceramics with a ratio close to the elemental ratios of MgTiO3 and Mg2TiO4 phases. Thus, the phase analysis in the test ceramics based on XRD and EDX tests supports each other.
SINTESIS DAN KARAKTERISASI GRAPHENE OXIDE (GO) YANG DIMODIFIKASI DENGAN NANOPARTIKEL SILIKA BERBASIS LIMBAH CANGKANG SAWIT Paramundhita, Frizky Audis; Munasir; Evi Suaebah
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p369-376

Abstract

Abstrak Penelitian ini dilakukan dengan tujuan untuk menghasilkan dan mengkaji karakteristik nanokomposit graphene oxide (GO) yang telah dimodifikasi dengan nanopartikel silika (SiO₂), menggunakan limbah cangkang kelapa sawit sebagai sumber karbon. Tahapan awal meliputi pembuatan karbon aktif melalui proses aktivasi kimia menggunakan larutan NaOH, kemudian dilanjutkan dengan sintesis GO melalui metode Hummers yang telah dimodifikasi, serta sintesis komposit GO–SiO₂ dengan memanfaatkan prekursor TEOS (Tetraethyl Orthosilicate). Karakterisasi struktur material menggunakan X-Ray Diffraction (XRD) dan Fourier Transform Infrared Spectroscopy (FTIR). Berdasarkan hasil uji karakterisaasi, data XRD menunjukkan pergeseran sudut difraksi dari 2θ = 24,2° pada GO menjadi 23,8° pada GO-SiO₂, yang mengindikasikan peningkatan jarak antar bidang kristal dari 3,67 Å menjadi 3,73 Å, disertai dengan penurunan ukuran kristalit dari 3,7 nm menjadi 3,5 nm. Spektrum FTIR menunjukkan kehadiran gugus O–H, C=O, dan Si–O–Si, menguatkan terbentuknya struktur komposit. Analisis SEM memperlihatkan adanya nanopartikel silika yang menempel pada permukaan GO, sementara hasil EDX mengonfirmasi keberadaan unsur silikon sebesar 3,6% pada komposit GO–SiO₂, disertai peningkatan oksigen dan penurunan karbon yang menunjukkan keberhasilan proses modifikasi. Secara keseluruhan, hasil ini mengindikasikan bahwa limbah cangkang kelapa sawit memiliki prospek sebagai sumber material karbon yang berkelanjutan untuk pengembangan komposit GO–SiO₂ yang fungsional dan ramah lingkungan.   Abstract This study aims to produce and evaluate the characteristics of graphene oxide (GO) nanocomposites modified with silica nanoparticles (SiO₂) by utilizing palm shell waste as a carbon source. The initial stage includes the production of activated carbon through a chemical activation process using NaOH solution. Then continued with the synthesis of GO through the modified Hummers method, and the synthesis of GO–SiO₂ composites using Tetraethyl Orthosilicate (TEOS) as a precursor. Characterization of the material structure was carried out using X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). XRD analysis showed a shift in the diffraction angle from 2θ = 24.2° for GO to 23.8° for GO-SiO₂, which indicated an increase in the interlayer distance from 3.67 Å to 3.73 Å, accompanied by a decrease in the crystallite size from 3.7 nm to 3.5 nm. The FTIR spectrum shows the presence of O–H, C=O, and Si–O–Si groups, strengthening the formation of the composite structure. SEM analysis shows the presence of silica nanoparticles attached to the GO surface, while EDX results confirm the presence of silicon elements of 3.6% in the GO–SiO₂ composite, accompanied by an increase in oxygen and a decrease in carbon indicating the success of the modification process. Overall, these results indicate that palm kernel shell waste has the prospect of being a sustainable source of carbon material for the development of functional and environmentally friendly GO–SiO₂ composites.
STUDI AKURASI CENTROID MOMENT TENSOR (CMT) PADA SOFTWARE JOKO TINGKIR DI WILAYAH KEPULAUAN MALUKU DENGAN PENDEKATAN SUDUT KAGAN DAN STATISTIKA INFERENSIAL Wardani, Jihan Nurrahma; Muhammad Nurul Fahmi; Madlazim
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p377-388

Abstract

Abstrak Penentuan parameter mekanisme sumber gempa yang akurat sangat penting dalam kajian seismotektonik dan mitigasi bencana. Penelitian ini bertujuan untuk mengevaluasi keakuratan hasil inversi Centroid Moment Tensor (CMT) yang dihasilkan oleh perangkat lunak Joko Tingkir menggunakan pendekatan sudut Kagan dan analisis statistik inferensial, serta untuk mengkaji karakteristik sesar di wilayah Kepulauan Maluku. Penelitian dibatasi pada 25 kejadian gempa dengan magnitudo moment (Mw > 5) yang terjadi selama periode 2020 hingga 2024. Hasil perhitungan sudut Kagan menunjukkan bahwa seluruh data memiliki nilai dalam rentang 5° hingga 37°, berada jauh di bawah batas kritis 60° yang mengindikasikan tingkat kesesuaian tinggi antara Joko Tingkir dan katalog GCMT. Uji statistik parametrik menghasilkan nilai t untuk masing-masing parameter: strike (-0,431), dip (-0,164), rake (-0,991), latitude (-1,003), longitude (-0,205), dan depth (1,109), semuanya masih dalam rentang toleransi (±2,06). Nilai z-score untuk parameter Mw juga berada dalam batas wajar yaitu -1,883, tidak melampaui nilai kritis ±1,96. Dengan demikian, tidak ditemukan perbedaan signifikan secara statistik maupun visual antara kedua dataset. Selain itu, hasil inversi mengungkapkan bahwa wilayah Kepulauan Maluku didominasi oleh tiga tipe mekanisme patahan yaitu strike-slip, thrust, dan oblique reverse yang masing-masing berasosiasi dengan struktur aktif seperti Sesar Kawa, Banda Detachment, Snellius Ridge, dan Morotai Trough. Temuan ini mencerminkan dinamika tektonik yang kompleks akibat interaksi antara lempeng utama dan mikrolempeng di kawasan tersebut.   Abstract Accurate determination of earthquake focal mechanism parameters is crucial for seismotectonic analysis and disaster mitigation. This study aims to evaluate the accuracy of Centroid Moment Tensor (CMT) inversion results generated by the Joko Tingkir software using the Kagan angle approach and inferential statistical methods, as well as to examine fault characteristics in the Maluku Islands region. The research is restricted to 25 earthquake events with a moment magnitude (Mw > 5) that occurred between 2020 and 2024. Kagan angle calculations indicate that all data pairs have values ranging from 5° to 37°, well below the critical threshold of 60°, suggesting a high level of similarity between Joko Tingkir and the GCMT catalogue. Parametric statistical tests yielded t-values for each parameter as follows: strike (-0.431), dip (-0.164), rake (-0.991), latitude (-1.003), longitude (-0.205), and depth (1.109), all within the acceptable range of ±2.06. The Z-score for the Mw parameter was -1.883, also within the critical range of ±1.96. These results indicate no statistically or visually significant differences between the two datasets. Furthermore, the inversion results reveal that the Maluku region is dominated by three faulting types: strike-slip, thrust, and oblique reverse, each associated with major active structures such as the Kawa Fault, Banda Detachment, Snellius Ridge, and Morotai Trough. These findings reflect the region’s complex tectonic dynamics resulting from interactions between major tectonic plates and microplates.
RANCANG BANGUN ALAT DETEKSI DISLEKSIA BERBASIS ELEKTROENSEFALOGRAFI DAN MIKROKONTROLER Febrianto, Dharmayuda; Muhimmatul Khoiro
Inovasi Fisika Indonesia Vol. 15 No. 1 (2026): Inpress Vol 15 No 1
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v15n1.p1-13

Abstract

Abstrak Disleksia adalah gangguan neurobiologis yang memengaruhi kemampuan membaca, menulis, dan mengeja, yang berdampak pada sekitar 19,8% siswa sekolah dasar di Indonesia. Penelitian ini bertujuan untuk mengembangkan alat deteksi disleksia berbasis Elektroensefalografi (EEG) yang terintegrasi dengan mikrokontroler ESP32. Sistem ini dirancang untuk memproses sinyal EEG dari subjek normal dan disleksia untuk merekam data aktivitas listrik otak selama pengujian. Dalam penelitian ini, sistem deteksi terdiri dari elektroda EEG, penguat sinyal AD8232, dan mikrokontroler ESP32 yang mengirimkan data ke platform ThingSpeak untuk analisis lebih lanjut. Alat ini dikalibrasi menggunakan input Audio Function Generator (AFG) dan output osiloskop untuk memastikan kemampuan membaca sinyal frekuensi gelombang neuron (4 Hz, 20 Hz, 40 Hz). Proses pengambilan data dilakukan dengan menempatkan elektroda pada titik-titik tertentu di kepala subjek, diikuti dengan pencatatan aktivitas listrik otak saat subjek mengerjakan tugas tertentu. Data yang diperoleh kemudian diproses melalui filter bandpass untuk menyaring sinyal yang tidak relevan, sebelum diubah menjadi amplitudo frekuensi gelombang otak (theta, beta, gamma) yang digunakan untuk analisis. Hasil penelitian menunjukkan adanya perbedaan signifikan dalam amplitudo gelombang theta dan gamma antara subjek disleksia dan subjek normal, yang menandakan adanya gangguan dalam pemrosesan informasi kognitif pada subjek disleksia. Dengan demikian, sistem ini menawarkan solusi yang lebih efisien, portabel, dan terjangkau untuk deteksi dini disleksia. Alat ini berpotensi untuk memperluas aksesibilitas diagnosis dan intervensi yang lebih cepat dan tepat bagi anak-anak dengan disleksia, serta dapat menjadi dasar untuk pengembangan lebih lanjut dalam bidang ini.   Abstract Dyslexia is a neurobiological disorder that affects the ability to read, write, and spell, impacting approximately 19.8% of primary school students in Indonesia. This study aims to develop a dyslexia detection tool based on Electroencephalography (EEG), integrated with the ESP32 microcontroller. The system is designed to process EEG signals from both normal and dyslexic subjects to record brain electrical activity during testing. In this study, the detection system consists of EEG electrodes, the AD8232 signal amplifier, and the ESP32 microcontroller, which sends data to the ThingSpeak platform for further analysis. The tool was calibrated using an Audio Function Generator (AFG) input and oscilloscope output to ensure the ability to read neural wave frequency signals (4 Hz, 20 Hz, 40 Hz). Data acquisition was performed by positioning electrodes at specific points on the subject's head, followed by recording brain activity as the subject performed a task. The obtained data was then processed through bandpass filtering to remove irrelevant signals, before being converted into amplitude frequency data for theta, beta, and gamma waves used for analysis. The results show a significant difference in the amplitude of theta and gamma waves between dyslexic and normal subjects, indicating disruptions in cognitive information processing in dyslexic subjects. Therefore, this system offers a more efficient, portable, and affordable solution for early dyslexia detection. The tool has the potential to expand accessibility to diagnosis and enable faster, more accurate interventions for children with dyslexia, and can serve as a foundation for further development in this field.
ANALISIS NILAI REFLECTION LOSS DAN SIFAT LISTRIK PADA KOMPOSIT PANI/rGO/FE3O4 Laili Arin Ramadhani; Putri, Nugrahani Primary; Fitriana
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p389-395

Abstract

Abstrak Komposit berbasis Polianilin (PANI), reduced Graphene Oxide (rGO), dan Fe₃O₄ telah berhasil disintesis menggunakan metode polimerisasi in situ dengan memanfaatkan sumber bahan alam, yakni pasir besi Gunung Galunggung dan tempurung kelapa. Penelitian ini bertujuan untuk mengkaji potensi komposit tersebu sebagai material penyerap gelombang mikro. Karakterisasi dilakukan menggunakan Vector Network Analyzer (VNA) dan Electrochemical Impedance Spectroscopy (EIS). Hasil pengujian menunjukkan bahwa komposit mampu mencapai nilai reflection loss sebesar −40,48 dB pada frekuensi 10,1 GHz, nilai tersebut menandakan kemampuan penyerapan energi gelombang mikro hingga lebih dari 99%. Nilai permeabilitas 1,57 dan permitivitas 1,43 yang seimbang menunjukkan bahwa komposit ini memiliki pencocokan impedansi yang baik. Selain itu, nilai konduktivitas listrik yang diperoleh melalui pengujian EIS sebesar 1,19 × 10⁻³ S/cm turut mendukung mekanisme penyerapan gelombang tanpa menimbulkan pantulan berlebih. Temuan ini mengindikasikan bahwa komposit PANI/rGO/Fe₃O₄ kinerja yang sangat baik sebagai penyerap gelombang mikro, dengan struktur elektromagnetik dan sifat listrik yang saling mendukung untuk mengoptimalkan penyerapan energi gelombang.   Abstract Composites based on Polyaniline (PANI), reduced Graphene Oxide (rGO), and Fe₃O₄ have been successfully synthesized using the in situ polymerization method by utilizing the source of natural materials, namely Galunggung Mountain iron sand and coconut shell. This research aims to assess the potential of the composite as a microwave absorber. Characterization was conducted using Vector Network Analyzer (VNA) and Electrochemical Impedance Spectroscopy (EIS). The test results show that the composite is able to achieve a reflection loss value of -40.48 dB at a frequency of 10.1 GHz, this value indicates the ability to absorb microwave energy to more than 99%. The balanced permeability value of 1.57 and permittivity of 1.43 indicates that this composite has excellent impedance matching. In addition, the electrical conductivity value obtained through EIS testing of 1.19 × 10-³ S/cm also supports the wave absorption mechanism without causing excess reflections. These findings indicate that the PANI/rGO/Fe₃O₄ composite performs very well as a microwave absorber, with mutually supportive electromagnetic and electrical structures to optimize the energy absorption of waves.
PENCITRAAN RUPTURE GEMPABUMI BANGGAI SULAWESI TENGAH 12 APRIL 2019 MW 6.8 MENGGUNAKAN METODE MULTIPLE SIGNAL CLASSSIFICATION BACK-PROJECTION Rahma Dian Wulan Dari; Madlazim; Fahmi, Muhammad Nurul
Inovasi Fisika Indonesia Vol. 14 No. 3 (2025): Vol 14 No 3
Publisher : Prodi Fisika FMIPA Universitas Negeri Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26740/ifi.v14n3.p412-420

Abstract

Abstrak Sulawesi Tengah merupakan daerah dengan tingkat seismisitas yang tinggi. Gempa bumi berkekuatan besar sering terjadi baik di daratan atau di lautan. Pada tanggal 12 April 2019 telah terjadi gempa bumi berkekuatan Mw 6,8 mengguncang Banggai Sulawesi Tengah. Penelitian ini dilakukan dengan tujuan menganalisis karakteristik rupture gempa Banggai menggunakan metode Multiple Signal Classification Back Projection. Data yang digunakan dalam penelitian ini merupakan data sekunder yang didapatkan dari IRIS WILBER 3 berupa gelombang seismik dari stasiun array AU dengan jumlah 73 sinyal. Metode yang digunakan dalam penelitian ini dengan teknik pemrosesan array AU berformat .SAC dan data tersebut diolah menggunakan program MUSICBP. Hasil analisis citra rupture beresolusi tinggi mendeskripsikan rupture gempa merambat secara unilateral sepanjang ~40 km/s dari episenter, dengan kecepatan 1,6 km/s dan durasi sebesar 25 Sekon. Hasil dari pencitraan rupture menunjukkan gempa bumi yang terjadi di Banggai pada 12 April 2019 disebabkan oleh aktivitas sesar Peleng di Pulau Sulawesi Tengah dengan rupture merambat ke arah Timur Laut dengan mekanisme Strike-Slip. Hasil akurasi MUSICBP yang didapatkan untuk mengetahui karakteristik rupture cukup akurat, yaitu dengan memvalidasi melalui IRIS WILBER 3. Ada sedikit perbedaan arah dengan penelitian terdahulu, akan tetapi lokasi penyebab nya menuju sesar yang sama, yaitu sesar Peleng.   Abstract Central Sulawesi is a region with a high level of seismicity. Large-magnitude earthquakes frequently occur both on land and at sea. On April 12, 2019, an earthquake with a magnitude of Mw 6.8 struck Banggai, Central Sulawesi. This study aims to analyze the rupture characteristics of the Banggai earthquake using the Multiple Signal Classification Back Projection (MUSICBP) method. The data used in this study are secondary data obtained from IRIS WILBER 3, consisting of seismic waveforms recorded by the AU array station, totaling 73 signals. The method employed in this research involved processing the AU array data in .SAC format, which were analyzed using the MUSICBP program. The results of the high-resolution rupture imaging describe that the rupture propagated unilaterally along approximately 40 km from the epicenter, at a speed of 1.6 km/s, with a duration of about 25 seconds. The rupture imaging results indicate that the earthquake that occurred in Banggai on April 12, 2019, was caused by the activity of the Peleng Fault in Central Sulawesi, with the rupture propagating toward the northeast and exhibiting a strike-slip mechanism. The MUSICBP analysis result were obtained to understand the characteristics of the fracture, specifically through validation using IRIS Wilber 3. There were slight differences between the direction and previous studies, but the location of the cause was the same, Fault Peleng.