cover
Contact Name
Brave A. Sugiarso
Contact Email
brave@unsrat.ac.id
Phone
+6282195447295
Journal Mail Official
ejournal.elektro@unsrat.ac.id
Editorial Address
https://ejournal.unsrat.ac.id/index.php/elekdankom/about/editorialTeam
Location
Kota manado,
Sulawesi utara
INDONESIA
Jurnal Teknik Elektro dan Komputer
ISSN : 23018402     EISSN : 2685368X     DOI : 10.35793
This e-journal is a publication and information forum for papers, theses, research, planning, and design concepts, as well as analysis from students, lecturers, or other writers. The scope of the articles published in this journal deal with a broad range of topics, including : Electronics engineering, Computer engineering, Computer science, Power engineering, Control engineering, Artificial Engineering
Articles 447 Documents
Analisis dan Perancangan Jaringan WiMAX di Fakultas Teknik UNSRAT Manado Antonie B. Uang; Arie S.M. Lumenta; Aneke P. R. Wowor
Jurnal Teknik Elektro dan Komputer Vol. 2 No. 4 (2013): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v2i4.2929

Abstract

Abstract - WiMAX (Worldwide Interoperability for Microwave Access) is a wireless network communication technology to make easy the information interchange especially about the internet or information in human life. The characteristic development of modern society which has high mobility, demands for flexible and economic service, in anywhere and anytime. Accordingly, computer network with WiMAX, formally called IEEE 802.16, which is much better and efficient than any other network technology, is very needed in Technique Faculty of Sam Ratulangi University. The computer network designed with WiMAX in Technique Faculty through BWA to connect the sector A and sector B, compares the WiFi network that only reaches 30 metres radius and its ability  in sending data only 11 Mbps which sets between 2,4 GHz and 5 GHz. WiMAX network can reach approximately 40 – 50 kilometres radius with ability in sending data up to 75 Mbps in low frequency and with its bandwith between 2 – 6 GHz either in Line of Sight (LoS) or Non Line of Sight (NLoS). This thesis analizes the Bit Rate, Receive Signal Level, Free Space Zone, radiaton energy and device requirement of WiMAX in Technique Faculty of Sam Ratulangi University. Keyword: Frequency, Network, Standard IEEE 802.16, WiFi, WiMAX Abstrak - WiMAX (Worldwide Interoperability for Microwave Access) merupakan teknologi komunikasi jaringan Wireless yang dapat memudahkan dalam pertukaran informasi terutama kebutuhan internet atau informasi dalam kehidupan manusia. Perkembangan karakteristik masyarakat modern  yang memiliki mobilitas tinggi, menuntut layanan yang lebih fleksibel serta ekonomis dimanapun dan kapanpun. Untuk itu, perlu adanya jaringan komputer yang baik dan efisien di kampus Fakultas Teknik Universitas Sam Ratulangi Manado dengan jaringan WiMAX Secara resmi disebut standart IEEE 802.16. Perancangan jaringan komputer menggunakan WiMAX di Fakultas Teknik melalui BWA untuk menghubungkan sektor A ke Sektor B,  menganalisis perbandingan jaringan WiFi yang hanya menjangkau sekitar radius 30 meter, dan kemampuan menghantarkan data hanya 11 Mbps yang diatur dalam frekuensi 2,4 GHz dan 5 GHz. Jaringan WiMAX memiliki jangkauan radius 40-50 kilometer, kemampuan menghantarkan data sampai dengan 75 Mbps yang berada di frekuensi cukup rendah dan lebar 2-6 GHz  dalam kondisi  Line of Sight (LoS) maupun Non Line of Sight (NLoS). Analisis dalam skripsi ini mencakup analisa Bit Rate, Receive Signal Level, Free Space Zone, daya pancar, dan kebutuhan perangkat WiMAX di area Fakultas Teknik UNSRAT. Kata Kunci : Frekuensi, Jaringan, Standart IEEE 802.16, WiFi, WiMAX
RANCANG BANGUN APLIKASI SISTEM PENDETEKSI KEKERUHAN AIR MENGGUNAKAN MIKROKONTROLER AVR ATMEGA 8535 Lusia E. Manik; Meicsy E.I. Najoan; Arthur M. Rumagit; Brave A. Sugiarso
Jurnal Teknik Elektro dan Komputer Vol. 2 No. 5 (2013): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v2i5.3362

Abstract

Abstract  - Water is a source of the life, not only for human but also for other living things. Clean water is one of a fine resource and it can be used for human consumptions or doing many activities on daily basis. Nowdays the availability of clean water is limited. Based on that, we have designed a tool can measure the frayed of the water with LDR (Light Dependent Resistor) censor which can detect water from level of LED (Light Emitting Diode) which can get through the water, so it will detect the frayed of the water. The process and control unction are doing by ATMega 8535. The output from this tool is a voltage and frayed water, which will be proceed with VB (Visual Basic) Program and visualised at PC (Personal Computer). On the 20 cm height water with 5 litre volume, it can get clean water is on 0.17 Volt, medium frayed water is on 0.17 till 0.18 Volt, and frayed water is on 5 Volt. Keywords: ATMega 8535, LED, Censor LDR, PC, VB   Abstrak - Air merupakan sumber kehidupan, tidak hanya bagi manusia, makhluk hidup yang lain juga sangat membutuhkan sir. Air bersih merupakan salah satu jenis sumber daya yang baik dan dimanfaatkan oleh manusia untuk dikonsumsi atau melakukan aktivitas sehari-hari. Saat ini ketersediaan air bersih sudah terbatas. Untuk itu, maka dirancanglah suatu alat yang dapat mengukur suatu kekeruhan air dengan menggunakan sensor LDR (Light Dependent Resistor), dimana sensor ini dapat mendeteksi air dari tingkat cahaya LED (Light Emitting Diode) yang menembus air tersebut, maka akan terdeteksi kekeruhan air. Pemprosesan dan pengendalinya dilakukan oleh ATMega 8535. Keluaran dari alat ini adalah tegangan dan kekeruhan air, yang diolah dengan pemograman VB (Visual Basic) dan ditampilkan di PC (Personal Computer). Pada ketinggian air 20 cm dengan volume 5 Liter, diperoleh air jernih bernilai tegangan 0.17 Volt, air setengah keruh 0.17 Volt sampai 0.18 Volt, sedang air keruh 5 Volt. Kata kunci: ATMega 8535, LED, Sensor LDR, PC, VB
Rancang Bangun Robot Pengantar Makanan Line follower Daisy A.N. Janis; David Pang; Janny O Wuwung
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3727

Abstract

Abstract-- The development of industrial technology and automation encourages people to meet their needs quickly. So that the robotic technology is developed to assist and ease human’s work in the future. Food delivery-line follower robot is a robot that is created​​ to replace the role of a waiter in a restaurant. This robot has the ability to deliver foods automatically. This reasearch using 4 pairs of LED and photodiode, a motor driver used to control 2 DC motors, 2 relay drivers to control DC motor for laying the food, ISD17240 module to produce sounds and the ATMEGA 16 microcontroller as the brain of this robot. The C Code Vision AVR is used as the Programming Language. This research produce a robot that can deliver foods up to two destination table by following a track of black line. Time needed to get to the second table is longer than to the first table because of the track length differences. Thus, this Food Delivery-Line Follower robot can function properly. Keywords: DI-Smart AVR, food delivery Robot, line follower, Microcontroller ATMega 16 Abstrak-- Perkembangan teknologi dan otomasi industri mendorong manusia untuk memenuhi kebutuhannya dengan cepat. Sehingga dikembangkan teknologi robotika untuk membantu dan meringankan pekerjaan manusia di masa depan. Robot pengantar makanan line follower merupakan robot yang diciptakan untuk menggantikan peran seorang pelayan di restoran. Robot ini memiliki kemampuan untuk mengantarkan makanan secara otomatis. Penelitian ini menggunakan 4 pasang led dan photodiode, driver motor untuk mengendalikan 2 buah motor DC, 2 buah driver relay untuk mengendalikan motor DC untuk peletakan makanan, modul ISD17240 untuk menghasilkan suara dan mikrokontroler ATMEGA 16 sebagai otak pada sistem robot ini. Bahasa pemrograman yang digunakan adalah bahasa C Code vision AVR. Penelitian ini menghasilkan robot yang dapat mengantarkan makanan menuju 2 meja tujuan dengan mengikuti lintasan berupa garis berwarna hitam. Waktu yang ditempuh untuk menuju ke meja kedua lebih lama dibandingkan menuju ke meja pertama karena perbedaan panjang lintasan. Dengan demikian secara keseluruhan sistem pada robot pengantar makanan ini dapat berfungsi dengan baik. Kata Kunci : DI-Smart AVR, Line follower, Mikrokontroler ATMega 16, Robot pengantar makanan.
Perancangan dan Implementasi Sistem Pelayanan Berbasis Teknologi Informasi Komunikasi di Gereja Mawar Sharon Manado Jeine E. Sarite; Arie S.M. Lumenta; Brave A. Sugiarso
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3764

Abstract

Abstrack - Such rapid technological developments both in the field of computers or other, inevitably requires us to master the technology. Such rapid development of computers over the years also requires us to understand the technology. In the management of praise and worship team schedule still using manual systems ranging from recording the name, manage schedules so that there are many errors see the reality of the church in need of a new system, the authors make the program processing schedules and admin can set the schedule online via the internet. Where the program is easy to use, helps the admin to manage the schedule and would like to introduce information technology advances to the church. This application combines the computer network systems and web-based database.r Keywords : Database, Computer, Information and Communication Technologies (ICT), online schedule . Abstrak  - Perkembangan teknologi yang demikian cepat baik dibidang komputer maupun dibidang lainnya, mau tidak mau mengharuskan kita agar menguasai teknologi tersebut. Perkembangan komputer yang demikian pesat dari tahun ke tahun juga mengharuskan kita agar memahami teknologi tersebut. Dalam pengelolaan jadwal tim praise and worship masih menggunakan sistem manual mulai dari pencatatan nama, mengelolah jadwal sehingga terjadi banyak kesalahan  melihat kenyataannya gereja membutuhkan sistem yang baru, penulis membuat program pengolahan jadwal dan admin bisa mengatur jadwal secara online melalui internet. Dimana program tersebut digunakan dengan mudah, membantu admin untuk mengelolah jadwal serta ingin memperkenalkan kemajuan teknologi informatika kepada jemaat. Program aplikasi ini memadukan antara jaringan komputer dengan sistem basis data dan berbasis web. Kata Kunci     :    Basis data, Jadwal online, Komputer, Teknologi informasi dan komunikasi (TIK).
Pengendali Saklar Listrik Melalui Ponsel Pintar Android Vidy Masinambow; Meicsy E.I Najoan; Arie S.M. Lumenta
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3772

Abstract

Abstract—With the development of technology such as smart phones that are already widely owned as well as the development of network technology can be used to overcome the problem of electricity consumtion. Electrical switches can be replaced by using the equipment controlled through a relay and network-based mikrokontler equipment so that it can connect to the smart phones which is mounted control program will be used to resolve the issue.Presence wifi shield equipment that can communicate with the microcontroller through serial communication so that information in the form of commands on / off switch that is sent from a smart phone with wireless connection to the equipment shield is a choice of solutions to address the replacement power switch.From the experimental results with the use of such technology, the Android-based smart phones that installed the control program can turn off the power switch or turn on electrical appliances from a considerable distance (as far as wifi connection is available).   Keywords: Android Smartphone, Electrical Switches,Microcontroller, Relays,  Wifi Shield Abstrak- Dengan perkembangan teknologi seperti ponsel pintar yang sudah banyak dimiliki orang serta perkembangan teknologi jaringan dapat digunakan untuk mengatasi masalah penghemataan listrik. Saklar listrik dapat diganti dengan menggunakan peralatan relay dan dikendalikan melalui peralatan mikrokontroler berbasis jaringan sehingga dapat terhubung ke ponsel pintar yang sudah terpasang program pengendali akan digunakan untuk mengatasi masalah tersebut. Adanya peralatan WifiShield yang dapat berkomunikasi dengan mikrokontroler melalui komunikasi serial sehingga informasi berupa perintah on/off saklar yang dikirim dari ponsel pintar dengan koneksi wirelesske peralatan wifishieldmerupakan pilihan solusi untuk mengatasi pengganti saklar listrik. Dari hasil percobaan denganmenggunakan teknologi tersebut, ponsel pinter berbasis androidyang terpasang program pengendali saklar listrik dapat mematikan atau menghidupkan peralatan listrik dari jarak yang cukup jauh (sejauh koneksi wifi yang tersedia). Kata kunci: Mikrokontroler, Ponsel Pintar Android,Relay, Saklar Listrik, WifiShield.
Rancang Bangun Sistem Keamanan Motor Dengan Pengenalan Sidik Jari Joyner R. Oroh; Elia Kendekallo; Sherwin R. U. A. Sompie; Janny O. Wuwung
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3773

Abstract

Abstrak - Perkembangan ilmu pengetahuan dan teknologi semakin meningkat terutama di bidang elektronika, banyak keuntungan yang dapat diperoleh dari perkembangan elektronika tersebut akan tetapi makin berkembangnya teknologi, makin banyak pula tindak kriminal, diantaranya pencurian motor. Dari permasalahan ini, dibuat system keamanan motor melalui pengenalan sidik jari. Sistem yang dibuat menggunakan sensor sidik jari Sm630 sebagai input untuk mendeteksi sidik jari dari pengguna sepeda motor. System ini juga didukung oleh kit arduino uno dengan mikrokontroler ATmega328 sebagai otak untuk mengolah data dari sensor sidik jari ke LCD, sepeda motor dan alarm. Dari pembuatan system ini, dapat disimpulkan bahwa, Hanya akan ada lima pengguna yang dapat mengakses sepeda motor dan system akan menghidupkan alarm saat ada sidik jari yang tidak sesuai menempel pada sensor karena sensor hanya akan berkomunikasi dengan sidik jari yang tersimpan dalam database sensor.   Kata kunci:     Arduino, ATmega 328, keamanan, sidik jari   Abstract - Developments in science and technology is increasing , especially in the field of electronics , many benefits can be gained from the development of the electronics but the growing technology the more criminal offenses, including theft of a motor. Of this problem, made motorcycle security system through fingerprint recognition. The system is made using a fingerprint sensor Sm630 as input to detect fingerprints of motorcycle users. This system is also supported by the kit with Arduino uno ATmega328 microcontroller as the brain to process the data from the fingerprint sensor to the LCD,  motorcycle and alarms. Of making this system, it can be concluded that, there will be only five users can access and motorcycle alarm system will turn on when there is no corresponding fingerprint sensor because the sensor attaches to will only communicate with fingerprint sensors are stored in the database .   Key words:     Arduino,ATmega 328,  finger print, security
E-tourism Kota Tobelo Kabupaten Halmahera Utara Stefan F. Pangalila; Arie S.M. Lumenta; Nancy J. Tuturoong
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3774

Abstract

Abstract - One very big in the presentation of information today is the need for the media information that is often used by the general public, companies, and state agencies. Crate Tobelo town which is a tourist spot that is not yet fully known to outsiders about the beauty of the tourist spot. Web programming has grown rapidly with many advantages that can be accessed diberbagi no such place. E-tourism Tobelo City North Halmahera using extreme programming as a methodology that includes plenning, design, coding, release. The results of this study lead to the conclusion. With the E-tourism Tobelo City North Halmahera then the tourists can be easier to search for information about KotaTobelo. The tourists get to know the culture in City Tobelo. The tourists are easier to get to know and know the language Tobelo City. Keywords :E-tourism, extreme programming, information, travel. Abstrak - Salah satu yang sangat besar dalam penyajian informasi sekarang ini adalah kebutuhan akan media informasi yang sering dipakai oleh masyarakat umum, perusahaan, dan instansi-instansi negara. Sepeti Kota Tobelo yang merupakan tempat wisata yang belum sepenuhnya dikenal pihak luar mengenai keindahan tempat wisatanya. Pemrograman web telah berkembang dengan pesat dengan banyak kelebihan yang ada seperti bisa diakses diberbagi tempat. E-tourism Kota Tobelo Kabupaten Halmahera Utara menggunakan extreme programming sebagai metodologi yang mencakup plenning, design, coding, rilis. Hasil dari penelitian ini memberikan kesimpulan. Dengan adanya E-tourism Kota Tobelo Kabupaten Halmahera Utara maka para wisatawan  dapat lebih mudah untuk mencari informasi tentang KotaTobelo. Para wisatawan lebih mengenal kebudayaan yang ada di Kota Tobelo. Para wisatawan lebih mudah untuk lebih mengenal dan mengetahui bahasa Kota Tobelo. Kata kunci :E-tourism, extreme programming,informasi, wisata.
Identifikasi Manfaat dan Analisa Investasi Pada Perusahaan Software House (Studi Kasus PT. XYZ) Karen V. L. Kapoyos; Jimmy R. Robot; Brave A. Sugiarso
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3780

Abstract

Abstract - The development of technology is now affecting every human activity, makes the job so much easier. Investment feasibility analysis is one way to simplify the calculation of the business to determine the feasibility of running a business, whether it's new or temporary will be implemented. Investment feasibility analysis in this paper uses investment criteria of Net Present Value (NPV), Payback Period (PP), and Internal Rate of Return (IRR). But before doing the calculation, we have to analyze the data that used to be used in the calculation of the investment. From the calculation, the value obtained in accordance with the criteria used and the requirements specified in each of the criteria : Net Present Value (NPV) is positive or >0 Rp.11,585,527,903, Payback Period (PP) gained 9.8 standard in 5 years <5 years, the Internal Rate of Return (IRR) of >40% is 209%. Thus, concluded the business is acceptable. Keywords : Feasibility Analysis, Internal Rate of Return, Investment, Net Present Value, Payback Period. Abstrak - Perkembangan teknologi saat ini sudah mempengaruhi setiap aktifitas manusia, membuat pekerjaan jadi lebih mudah. Analisa kelayakan investasi adalah salah satu cara mempermudah perhitungan bisnis untuk mengetahui kelayakan dalam menjalankan suatu bisnis, apakah itu baru akan atau sementara dilaksanakan. Analisa kelayakan investasi dalam tulisan ini menggunakan kriteria investasi Net Present Value (NPV), Payback Periode (PP), dan Internal Rate of Return (IRR). Namun sebelum melakukan perhitungan, kita harus menganalisis data yang digunakan untuk bisa dipakai dalam perhitungan  investasi. Dari hasil perhitungan, diperoleh nilai sesuai dengan kriteria yang digunakan dan dengan syarat yang ditentukan pada masing-masing kriteria, yaitu: Net Present Value (NPV) bernilai positif atau >0 Rp. 11.585.527.903, Payback Periode (PP) standart 5 tahun diperoleh 9,8 bulan <5 tahun, Internal Rate of Return (IRR) >40% yaitu 209%. Dengan demikian, disimpulkan bisnis dapat diterima. Kata kunci : Analisa Kelayakan, Internal Rate of Return, Investasi, Net Present Value, Payback Periode.
Perancangan Kendali Lampu Berbasis Android Immanuel Warangkiran; Sumenge T.G. Kaunang; Arie S.M. Lumenta; Arthur M. Rumagit
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.3827

Abstract

Abstract Smartphone with android operation system are getting more available in the markets with quite low price. Android operation system it self  has open source operation system which can be modified. This boosts the interest of creating software to fill in the needs of the people in everyday life. The aim of this last project is to create and implimate to control lamps that can be switch on or off from a smartphone based on android by using wireless LAN and to make android as multifunction cellular, not only as telecomunication device but as a device that can control any hardware. Based on the final experiment the system work well. The application lamps control can be applied in the operation system android, and can be controlled to switch on or switch off the hard drives in this case three lamps. The communication between the hard drives lamps and the smartphone android worked well. The range of the application system can control the hard drives lamps, it depends on the specification of the wireless tools between the receiver and the sender. Keywords: Android, Lamp, Smartphone, Wireless LAN. Abstrak Smartphone dengan sistem operasi Android semakin banyak tersedia di pasaran dengan harga yang semakin terjangkau. Sistem operasi Android sendiri bersifat sistem operasi open source yang dapat dimodifikasi sesuai dengan keperluan. Hal ini menumbuhkan minat untuk dapat membuat perangkat lunak yang bermanfaat dalam memenuhi kebutuhan manusia sehari-hari. Dalam Tugas Akhir ini bertujuan merancang dan mengimplementasikan, yaitu mengontrol lampu, mengaktifkan dan menonaktifkannya lewat smartphone berbasis android dengan memanfaatkan Wireless LAN dan menjadikan android sebagai perangkat selular yang multifungsi, di samping alat komunikasi tapi juga sebagai perangkat yang dikomunikasikan untuk mengendalikan sebuah perangkat keras. Berdasarkan hasil pengujian yang dilakukan, sistem dapat bekerja dengan baik sesuai dengan tujuan. Program aplikasi Lampu Control yang dibuat dapat dijalankan di sistem operasi Android, dan dapat mengaktifkan dan menonaktifkan perangkat driver lampu, dimana memakai 3 buah lampu. komunikasi data antara perangkat driver lampu dengan smartphone android berjalan dengan baik, Jarak jangkau sistem aplikasi kendali dapat mengontrol perangkat driver lampu tergantung spesifikasi perangkat wireless yang digunakan baik dari sisi penerima dan pengirim. Kata kunci:  Android, Lampu, Smartphone, Wireless LAN.
Perancangan PC Cluster Untuk Render Animasi 3D Brian W.K. Malubaya; Arthur M. Rumagit; Arie S.M. Lumenta; Brave A. Sugiarso
Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer
Publisher : Universitas Sam Ratulangi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35793/jtek.v3i1.4049

Abstract

Abstract Technology is very important role in human life from day to day. Technology has become part of human beings themselves that they cannot be separated. In its scope computerized, processor the data quickly and accurately is needed as a function of time. PC cluster is one of the answers from the statements upstairs. This cluster system allows some computers work together that are connected by a network of local so that resolving the issue can be shortened especially for completion of problem solving a large scale. Rendering is a process of transformation into a picture, models of geometry this process eat quite a long time. To address the problem of pc clusters implemented in this case. Cluster used for rendering called renderfarm by the force arising yadra as middleware. By doing so can be detected the time difference rendering use single computer and pc clusters. Having performed testing then he got that rendering use of pc clusters with 5 slaves faster 60% than single computer. By doing so, we need the further research for subsequent development. keywords:  cluster, render, renderfarm, yadra. Abstrak Teknologi sangat penting perannya dalam kehidupan manusia dari hari ke hari. Teknologi telah menjadi bagian dari manusia itu sendiri yang tak dapat dipisahkan. Dalam ruang lingkup komputerisasi, pemroses data yang cepat dan akurat sangat dibutuhkan seiring berjalannya waktu. PC cluster adalah salah satu jawaban dari pernyataan diatas. Sistem cluster ini memungkinkan beberapa komputer bekerja secara bersama yang dihubungkan oleh jaringan lokal sehingga penyelesaian masalah dapat dipersingkat terutama untuk penyelesaian masalah skala besar. Rendering adalah suatu proses pengubahan model geometri menjadi sebuah gambar, proses ini memakan waktu yang cukup lama. Untuk mengatasi masalah tersebut PC cluster diimplementasikan dalam kasus ini. Cluster yang digunakan untuk render disebut Renderfarm denga yadra sebagai middleware. Dengan begitu dapat diketahui perbedaan waktu render menggunakan single computer dan PC cluster. Setelah dilakukan pengujian maka didapatkan bahwa rendering menggunakan PC cluster 5 slave lebih cepat sekitar 60% dibandingkan dengan single computer. Dengan begitu maka perlu adanya penelitian lebih lanjut untuk pengembangan selanjutnya.   kata kunci:  cluster, render, renderfarm, yadra.

Page 9 of 45 | Total Record : 447


Filter by Year

2012 2024


Filter By Issues
All Issue Vol. 13 No. 02 (2024): Jurnal Teknik Elektro dan Komputer Vol. 13 No. 01 (2024): Jurnal Teknik Elektro dan Komputer Vol. 13 No. 3 (2024): Jurnal Teknik Elektro dan Komputer Vol. 12 No. 3 (2023): Jurnal Teknik Elektro dan Komputer Vol. 12 No. 2 (2023): Jurnal Teknik Elektro dan Komputer Vol. 12 No. 1 (2023): Jurnal Teknik Elektro dan Komputer Vol. 11 No. 3 (2022): Jurnal Teknik Elektro dan Komputer Vol. 11 No. 2 (2022): Jurnal Teknik Elektro dan Komputer Vol. 11 No. 1 (2022): Jurnal Teknik Elektro dan Komputer Vol. 10 No. 3 (2021): Jurnal Teknik Elektro dan Komputer Vol. 10 No. 2 (2021): Jurnal Teknik Elektro dan Komputer Vol. 10 No. 1 (2021): Jurnal Teknik Elektro dan Komputer Vol. 9 No. 3 (2020): Jurnal Teknik Elektro dan Komputer Vol. 9 No. 2 (2020): Jurnal Teknik Elektro dan Komputer Vol. 9 No. 1 (2020): Jurnal Teknik Elektro dan Komputer Vol. 8 No. 3 (2019): Jurnal Teknik Elektro dan Komputer Vol. 8 No. 2 (2019): Jurnal Teknik Elektro dan Komputer Vol. 8 No. 1 (2019): Jurnal Teknik Elektro dan Komputer Vol. 7 No. 3 (2018): Jurnal Teknik Elektro dan Komputer Vol. 7 No. 2 (2018): Jurnal Teknik Elektro dan Komputer Vol. 7 No. 1 (2018): Jurnal Teknik Elektro dan Komputer Vol. 6 No. 4 (2017): Jurnal Teknik Elektro dan Komputer Vol. 6 No. 3 (2017): Jurnal Teknik Elektro dan Komputer Vol. 6 No. 2 (2017): Jurnal Teknik Elektro dan Komputer Vol. 6 No. 1 (2017): Jurnal Teknik Elektro dan Komputer Vol. 5 No. 4 (2016): Jurnal Teknik Elektro dan Komputer Vol. 5 No. 3 (2016): Jurnal Teknik Elektro dan Komputer Vol. 5 No. 2 (2016): Jurnal Teknik Elektro dan Komputer Vol. 5 No. 1 (2016): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 7 (2015): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 6 (2015): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 5 (2015): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 4 (2015): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 3 (2015): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 2 (2015): Jurnal Teknik Elektro dan Komputer Vol. 4 No. 1 (2015): Jurnal Teknik Elektro dan Komputer Vol. 3 No. 5 (2014): Jurnal Teknik Elektro dan Komputer Vol. 3 No. 4 (2014): Jurnal Teknik Elektro dan Komputer Vol. 3 No. 3 (2014): Jurnal Teknik Elektro dan Komputer Vol. 3 No. 2 (2014): Jurnal Teknik Elektro dan Komputer Vol. 3 No. 1 (2014): Jurnal Teknik Elektro dan Komputer Vol. 2 No. 5 (2013): Jurnal Teknik Elektro dan Komputer Vol. 2 No. 4 (2013): Jurnal Teknik Elektro dan Komputer Vol. 2 No. 3 (2013): Jurnal Teknik Elektro dan Komputer Vol. 2 No. 2 (2013): Jurnal Teknik Elektro dan Komputer Vol. 2 No. 1 (2013): Jurnal Teknik Elektro dan Komputer Vol. 1 No. 4 (2012): Jurnal Teknik Elektro dan Komputer Vol. 1 No. 3 (2012): Jurnal Teknik Elektro dan Komputer Vol. 1 No. 2 (2012): Jurnal Teknik Elektro dan Komputer Vol. 1 No. 1 (2012): Jurnal Teknik Elektro dan Komputer More Issue