Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Bulletin of Electrical Engineering and Informatics

EEI
Website

Published by Universitas Ahmad Dahlan

ISSN : - EISSN : - DOI : -

Core Subject : Engineering,

Electrical & Electronics Engineering

Bulletin of Electrical Engineering and Informatics (Buletin Teknik Elektro dan Informatika) ISSN: 2089-3191, e-ISSN: 2302-9285 is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world. The journal publishes original papers in the field of electrical, computer and informatics engineering.

Arjuna Subject : -

Articles 2,901 Documents

52 53 54 55 56

Multiband antenna using stacked series array for Ka-Band application Rauful Nibir; Islam Md. Rafiqul; Mohamed Hadi Habaebi; Sarah Yasmin; Naimul Mukit; Sarah Rafiq; Abdinasir S. O
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

In this paper, a multiband stack series array antenna is designed in order to attain solutions for the future 28 GHz Ka-band application. Double layer substrate Technology is utilized to accomplish multiple resonant frequencies with higher data transfer capacities due to high bandwidth. The designed antenna is dependent on twofold layer consisting patches and resonators in different layers stacked together. The designed multiband antennas can resonate at single band of (28 GHz), dual band of (28 and 30 GHz) and triple band of (24.18, 26 and 28.453). The results achieved in the simulation are later fabricated and tested. The test result illustrates that the antennas have wide bandwidth, high gain and even higher efficiencies. All the proposed antenna configurations have demonstrated a decent possibility for 5G millimeter wave (mmwave) application.

Development of web-based surveillance system for Internet of Things (IoT) application Siti Noorjannah Ibrahim; A. H. Hasan Basri; Ani Liza Asnawi
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

With the advancement of wireless technology, our dependency on smart system has increases to a higher level than before. Without doubt, integration between different technologies becomes inevitable in order create affordable surveillance system. This paper presents the development of with web-based surveillance system with a dedicated Android-based mobile application using a Raspberry Pi and its supporting components i.e., Pi-Camera, PIR motion sensor, Ultrasonic sensor, web-based and mobile application. The designed system also utilizes Node-Red development tools as the platform to integrate all components of the system, MQTT as the communication protocol for data acquisition and ThingSpeak as the middleware. The proposed system can be implemented over the internet using any computer and mobile devices, at anywhere and anytime. The system can automatically stream live video viewed from the Android mobile application and the Raspberry Pi device can send an alert notification to users via email and SMS. The system can be one possible features in smart home system and is considered as an affordable solution, customizable and easy to implement in comparison with other commercial surveillance system products such as CCTV or IP Camera.

Investigation on the mass sensitivity of quartz crystal microbalance gas sensor using finite element simulation Aliza Aini Md Ralib; Nik Nursyahida Bt Nik Mohd Zamri; Ahmad Hafiz Faqruddin Hazadi; Rosminazuin Ab Rahim; Nor Farahidah Za’bah; Norazlina Saidin
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

The increasing global trends in healthcare priorities towards improving the effectiveness of diagnostic procedure by utilizing a non-invasive method which is breath analysis. This will benefit in increasing treatment efficiency and also reducing healthcare costs. Breath is a simple technique where the sample are easily obtained and can be provided immediately. The most popular method that had been used in hospital are urine and blood. Contradict with breath, urine and blood take too much time to analyse the disease and a painful process. The detection technique of breath analysis is done by using electroacoustic wave sensor from piezoelectric substrate. This acoustic wave sensor has been used to detect the changes in the frequency where it will be used to detect the disease. Breath analysis is a technique where it uses an electronic nose (E-nose) as a device. E-nose consist of Quartz Crystal Microbalance (QCM) sensor in order to differentiate odor in human breath. QCM is a sensitive weighing device which have a high efficiency. AT-cut quartz was chosen as the piezoelectric material and aluminum as the electrode. The objective of this paper is to design and simulate a QCM sensor for breath analysis application. Other than that, it also to determine the important key parameters that influence the performance of breath analysis which is sensitivity and resonant frequency. QCM sensor is being simulate by using COMSOL Multiphysics software. This is to evaluate the behavior of QCM sensor in terms of Eigen frequency analysis. The simulated QCM sensor with quartz radius of 166 um resonates at 8.871 MHz. The sensitivity of the sensor is 0.167 MHz/ng after exposed to acetone gas which act as the breath marker for detection of diseases in exhaled breath. Hence, the proposed design can be used as a non-invasive approach for early detection of disease through breath analysis.

Design and parametric evaluation of UWB antenna for array arrangement Faraz Ahmed Shaikh; Sheroz Khan; A H. M. Zahirul Alam; Dominique Baillargeat; Mohamed Hadi Habaebi; Mashkuri Bin Yaacob; Jawad Shah; Zeeshan Shahid
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

This paper has introduced the concept of UWB antenna in array arrangements. The four elements of Balance Antipodal Vivaldi Antenna (BAVA) has been used for planar and H-plane array configuration in this research. Each single element of BAVA Antenna is printed on the glass-reinforced epoxy laminate material (FR4) along an overall thickness of 1.57mm and εr=4.3 respectively. The optimized measurement of each particular element is 60.75mm x 66mm approximatel. Further the parametric evaluation of four BAVA elements in different planes has been observed in this paper. The placement of array elements has almost coverd entire UWB frequency range and appropriate reflection coefficient which is better than -10dB has been established in both combinations. According to simulation results, the array elements in planar arrangement presenting a suitable reflection and works well at 3.2GHz frequency while the arrangement in H-plane the array elements works well at 7GHz of frequency. In planar arrangement, the operating frequency of antenna elements is shifting as results of the distance among inter elements which increase in wavelength. In H-plane arrangement an antenna elements generate additional gain up to 10.2 dB with good radiation patterns as compared to the planar plane. The CSTMWS simulation software has been used for antenna structural design and parametric verification.

Recyclable waste separation system based on material classification using weight and size of waste Nur Shahida Midi; Muhammad Aizat Rahmad; Siti Hajar Yusoff; Sarah Yasmin Mohamad
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Insufficient landfills problem had increased the needs to decrease the waste and recycling them. However, despite the efforts done by the government and local authorities on promoting recycling culture by introducing new laws and regulations, the awareness and willingness among the community is still low. One of the possible reasons to this is lack of effort to categorize the waste into the designated category which are paper, glass, plastic and metal. In order to address this problem, it is important to design a system that will ease the process of categorizing the waste. This can be achieve by the automation of the said process. In this work, a system consist of an algorithm and hardware to automatically categorize recyclable waste is proposed. The proposed system are utilizing weight sensor and ultrasonic sensors in order to capture the characteristics of the waste item, which are weight and size so that it can be categorized into paper, glass, plastic and metal. Here, a sytem to automatically separate household waste item is presented by combining an algorithm with a set of hardware consist of minimal number of sensors, conveyer belt and servor motors.

Frequency dependency analysis for differential capacitive sensor Nurul Arfah Che Mustapha; A. H. M. Zahirul Alam; Sheroz Khan; Amelia Wong Azman
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

A differential capacitive sensing technique is discussed in this paper. The differential capacitive sensing circuit is making use of a single power supply. The design focus for this paper is on the excitation frequency dependency analysis to the circuit. Theory of the differential capacitive sensor under test is discussed and derivation is elaborated. Simulation results are shown and discussed. Next, results improvement has also been shown in this paper for comparison. Test was carried out using frequency from 40 kHz up to 400 kHz. Results have shown output voltage of Vout=0.07927 Cx+1.25205 and good linearity of R-squared value 0.99957 at 200 kHz. Potential application for this capacitive sensor is to be used for energy harvesting for its potential power supply.

MM-PNEMO: a mathematical model to assess handoff delay and packet loss Shayla Islam; Aisha Hassan Abdalla Hashim; Mohammad Kamrul Hasan; Md. Abdur Razzaque
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Wireless networks incorporate Mobile Nodes (MNs) that use wireless access networks to communicate. However, the communication among these MNs are not remained stable due to the poor network coverage during inter mobility. Moreover, the wireless nodes are typically small that results in resource-constrained. Thus, it is uphill to use algorithms having giant processing power or memory footprint. Accordingly, it is essential to check schemes consistently to evaluate the performance within the probable application scenario. To do so, numerical analysis could be a notable method to grasp the performance of mobility management schemes as well as the constraint of evolving mobility management solutions specifically for multi-interfaced MR in Proxy NEMO environment. This paper analyzes handoff performance by using a mathematical model of Multihoming-based scheme to support Mobility management in Proxy NEMO (MM-PNEMO) environment. Moreover, a comparative study has been made among the standard Network Mobility Basic Support Protocol (NEMO BSP), Proxy NEMO (PNEMO) and MM-PNEMO scheme respectively. The performance metrics estimated for these schemes are mainly handoff delay and packet loss. This paper also analysed the packet loss ratio and handoff gain as a function of cell radius, number of SMR and velocity respectively. It is apparent that, the MM-PNEMO scheme shows lower packet loss ratio (1%) compared to NEMO-BSP (11%) and P-NEMO (6%).

Parasitic consideration for differential capacitive sensor Nurul Arfah Che Mustapha; A. H. M. Zahirul Alam; Sheroz Khan; Amelia Wong Azman
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

Parasitic integration for a single supply differential capacitive sensing technique is presented in this paper. In real capacitive sensor measurement, parasitic impedance exists in its measurement. This paper objective is to study the effect of capacitive and resistive parasitic to the capacitive sensor circuit. The differential capacitive sensor circuit derivation theory is elaborated first. Then, comparison is made using simulation. Test was carried out using frequency from 40 kHz up to 400 kHz. Result is presented and have shown good linearity of 0.99984 at 300 kHz, R-squared value. This capacitive sensor is expected to be used for energy harvesting application.

Energy efficient smart street light for smart city using sensors and controller Aziera Abdullah; Siti Hajar Yusoff; Syasya Azra Zaini; Nur Shahida Midi; Sarah Yasmin Mohamad
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Smart street light is an intelligent control of street lights to optimize the problem of power consumption of the street, late in night. Conventional street lights are being replaced by Light Emitting Diode (LED) street lighting system, which reduces the power consumption. The focus of this project is to design a system of street lights controller to provide a reduction in power consumption. The prototype was designed by using Light Dependent Resistor (LDR), Infrared sensor (IR), battery and LED. The brightness of the lamps is being controlled in this project to reduce the power consumption. The dimming of the lamps depends on the speed of object motion detected such as pedestrians, cyclists and cars. The higher speed of moving object, the greater the level of intensity. For this idea, the innovation of street lights is not quite the same as conventional street lights that are controlled by timer switch or light sensor which automatically turns light on during sunset and off during sunrise. According to the study, motion detection devices may help to save up to 40% of energy per month.

Analysis of airborne dust effects on terrestrialmicrowave propagation in arid area Elfatih A. A. Elsheikh; Islam Md. Rafiqul; Mohamad Hadi Habaebi; Ahmad F. Ismail; Z. E. O. Elshaikh; F. M. Suliman; Jalel Chebil
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

Sand and dust storms are environmental phenomena ,during these storms optical visibility might be decreased, consequently, atmospheric attenuation is clearly noticed.Micro-wave (MW) and Milimeter-wave (mm) propagation is severely affected by dust and sand storms in considerable areas around the world. Suspended dust particles may directly cause attenuation and cross polarization to the Electromagnetic waves propagating through the storm. In this paper, a thorough investigation of dust storm characteristics based onmeasured optical visibility and relative humidity is presented. In addition,the dust storms effects of on Micro-wave and Millimeter-wave propagation have been studied based on data measured Received Signal levels (RSL)and dust storm characteristics synchronously. Analyticaldustattenuationmodels predictions are matched to the measured attenuationdata at 14 GHz and 21 GHz. It has been found that the measured attenuation is approximately ten times higher than the predicted attenuation for both frequencies.

Page 54 of 291 | Total Record : 2901

52 53 54 55 56

Filter by Year

2012 2025

Filter By Issues

All Issue Vol 14, No 6: December 2025 Vol 14, No 5: October 2025 Vol 14, No 4: August 2025 Vol 14, No 3: June 2025 Vol 14, No 2: April 2025 Vol 14, No 1: February 2025 Vol 13, No 6: December 2024 Vol 13, No 5: October 2024 Vol 13, No 4: August 2024 Vol 13, No 3: June 2024 Vol 13, No 2: April 2024 Vol 13, No 1: February 2024 Vol 12, No 6: December 2023 Vol 12, No 5: October 2023 Vol 12, No 4: August 2023 Vol 12, No 3: June 2023 Vol 12, No 2: April 2023 Vol 12, No 1: February 2023 Vol 11, No 6: December 2022 Vol 11, No 5: October 2022 Vol 11, No 4: August 2022 Vol 11, No 3: June 2022 Vol 11, No 2: April 2022 Vol 11, No 1: February 2022 Vol 10, No 6: December 2021 Vol 10, No 5: October 2021 Vol 10, No 4: August 2021 Vol 10, No 3: June 2021 Vol 10, No 2: April 2021 Vol 10, No 1: February 2021 Vol 9, No 6: December 2020 Vol 9, No 5: October 2020 Vol 9, No 4: August 2020 Vol 9, No 3: June 2020 Vol 9, No 2: April 2020 Vol 9, No 1: February 2020 Vol 8, No 4: December 2019 Vol 8, No 3: September 2019 Vol 8, No 2: June 2019 Vol 8, No 1: March 2019 Vol 7, No 4: December 2018 Vol 7, No 3: September 2018 Vol 7, No 2: June 2018 Vol 7, No 1: March 2018 Vol 6, No 4: December 2017 Vol 6, No 3: September 2017 Vol 6, No 2: June 2017 Vol 6, No 1: March 2017 Vol 5, No 4: December 2016 Vol 5, No 3: September 2016 Vol 5, No 2: June 2016 Vol 5, No 1: March 2016 Vol 4, No 4: December 2015 Vol 4, No 3: September 2015 Vol 4, No 2: June 2015 Vol 4, No 1: March 2015 Vol 3, No 4: December 2014 Vol 3, No 3: September 2014 Vol 3, No 2: June 2014 Vol 3, No 1: March 2014 Vol 2, No 4: December 2013 Vol 2, No 3: September 2013 Vol 2, No 2: June 2013 Vol 2, No 1: March 2013 Vol 1, No 4: December 2012 Vol 1, No 3: September 2012 Vol 1, No 2: June 2012 Vol 1, No 1: March 2012 List of Accepted Papers (with minor revisions) More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kota yogyakarta, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA